PXI Carriers
-
Product
PXI CAN Interface Module
CAN Interface
PXI CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate, Low-Speed/Fault Tolerant, and/or Single Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from FIBEX and DBC files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
PXI Load Resistor Module 10 Ohm to 2.56k
40-292-012
Load Resistor Module
A simple solution for applications requiring a programmable load resistor with up to 15W power handling. It is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
PXI 8 Slot BRIC 132x8 2-pole (6 sub-cards)
40-562A-122-132X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2 Amp MUX, Single 8-Channel 8-Pole
40-635-004
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-244-HI
Programmable Resistor Module
The 40-230-244-HI (PXI) and 42-230-244-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 8-Slot BRIC Matrix, 528x4 2-Pole (12 sub-cards)
40-562B-122-528X4
Matrix Switch Module
The 40-562B-122-528X4 is a high density BRIC8 matrix module with a size of 528x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Single 2 x 2 Insert/Bypass Switch FC/APC
40-860-012
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI 12-Slot BRIC Matrix, 88x4 1-Pole (2 sub-cards)
40-562B-321-88X4
Matrix Switch Module
The 40-562B-321-88X4 is a high density BRIC12 matrix module with a size of 88x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 2A Multiplexer, 4-Bank, 4-Channel, 8-Pole
40-614C-009
Multiplexer Module
This 4-bank, 4-channel, 8 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI Dual 8x4 1-Pole 5A Power Matrix
40-549-003
Matrix Switch Module
The 40-549 is a single pole power matrix module, suitable for switching inductive/capacitive loads up to 5A with 110VDC/250VAC hot switching and 400VDC/250VAC cold switching. It is available in single 16x4, single 8x8, dual 8x4 or single 8x4 configurations. Connections are made via a front panel 25 way D-type male connector.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 1.81kΩ
40-251-022
Programmable Resistor Module
The 40-251-022 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Single 4 Channel Fibre Optic Mux FC/APC
40-850-014
Fiber Optic Switch
The 40-850-014 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Monitored Multiplexer, Dual 64-Channel, 1-Pole
40-619-302
Multiplexer Module
The 40-619-302 is a high density PXI 2 A multiplexer module in dual 64-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC - Single
-
Product
PXI 8 Slot BRIC 110x16 2-pole (10 sub-cards)
40-562A-122-110X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI BRIC4 FIBO Matrix Dual 80x4 3pin brkout
40-592A-004
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI 4 Slot BRIC 66x16 2-pole (6 sub-cards)
40-562A-022-66X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI High-Density Multiplexer: 128-ch, 1-Wire, 100Vrms/1A, Reed Relays
M9102A
Multiplexer Module
The M9102A, a high-density, 128-channel multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time. This 1-wire multiplexer features high speed, long-life reed relays capable of switching up to 100Vrms, with up to 10W of power. Connection options include the durable connector block or the standard cable connections.
-
Product
PXI BRIC8 HD FIBO Matrix 186x8 2pin brkout
40-592-121-186X8-2P
Matrix Switch Module
The 40-592 FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC™ format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short-circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-01
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
PXI 8 Slot BRIC 220x8 2A 1-Pole Matrix
40-567-105
Matrix Switch Module
The 40-567 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-567 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXIe-8430, 8-Port, RS232 PXI Serial Interface Module
781472-01
Serial Interface
8-Port, RS232 PXI Serial Interface Module—The PXIe‑8430/8 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXI 8 Slot BRIC 174x6 2A 1-Pole Matrix
40-596-103
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 2 Slot BRIC 22x16 1-Pole (2 sub-cards)
40-562A-221-22X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
PXI 4 Slot BRIC 225x4 2A 1-Pole Matrix
40-568-003
Matrix Switch Module
The 40-568 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Digital I/O Module
Digital I/O Module
PXI Digital I/O Modules offer up to 96 channels of digital I/O, with compatibility for a variety of voltage and isolation levels. Some models include programmable input filters to eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter. PXI Digital I/O Modules are ideal for a range of applications, from manufacturing test and industrial control to advanced aerospace and laboratory research.
-
Product
PXI Multiplexer Dual 32 Ch 1 Pole
40-630-022-D/32/1
Multiplexer Module
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole, 4-pole and 1-pole screened.
-
Product
PXI Multiplexer, Dual 32-Channel, 1-Pole
40-630A-022-D/32/1
Multiplexer Module
The 40-630A-022-D/32/1 is a dual 32-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
CPCI Or PXI Communication Interface Board
MS 1706
-
*Memory and IO Read Write Cycles*External Interrupts*32 bit Data Bus*30 bit Address Bus*Control Signals for external interface*Four RS232 PORTS with full handshake signals*Four RS232/RS422 PORTS without handshake signals*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
PXI 2 Amp Multiplexer, Quad 4-Channel, 2-Pole
40-635A-109
Multiplexer Module
The 40-635A-109 is a quad 4-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 2-Slot BRIC Matrix, 66x8 1-Pole (3 Sub-cards)
40-562B-221-66X8
Matrix Switch Module
The 40-562B-221-66X8 is a high density BRIC2 matrix module with a size of 66x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
