Monitors
Continually examine for quality.
-
Product
Multipoint Gas Sampling System
MultiGard™ 5000
-
The economical, efficient MultiGard 5000 Gas Sampling System uses auto-standardization and flexible sample point order to analyze gas from up to 32 locations. Maintenance and calibration are made easy because all the work is performed at a single location, while also ensuring personnel don't have to enter the monitored area.
-
Product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
-
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
Product
Linear regulated power supply with thyristor pre-regulation
NTN
-
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
Product
Raman Spectrometers
-
The extensive Raman spectrometer family from Anton Paar offers the right instrument for what you want to do: Identify unknown substances, verify samples in quality assurance, analyze the chemical composition of samples, or monitor their changes.
-
Product
Tri-phase High Power Programmable AC Power Source
APS50000
-
Advanced direct digital frequency sythesizer(DDS) waveform generation technology, high frequency stability, good continutyMeasurement precision is high, suitable for current half-sinusoid and its similar waveforms with DC component measurementProvide embedded intelligent PC monitoring systemAdjustable output voltage from 0 to 150V, 0 to 300V, step distance 0.1VOutput frequency 45-120Hz(40-500Hz optional), step distance 0.1 HzOutput current limiting functionWith 9 sets of memory, you can store commonly used parameters for easy invocation when using themWith RS232C communication interface 【IEEE488.0(GPIB)optional】, instruction execution times is less than 10mSProtechtion mode: over voltage, over current, overload, short circuit,current limit, ectProvide RMS voltage, RMS current, active power, frequency, power factor, ectFor 100% load removal, voltage stabilizing reaction time within 20ms, strong overload capacity, instantaneouscurrent can with stand 3 times of rated current
-
Product
Current Sensing
-
voltage-output, current-sensing amplifier family that integrates an internal shunt resistor to enable high-accuracy current measurements at common-mode voltages that can vary from 0 V to 36 V, independent of the supply voltage. The device is a bidirectional, low- or high-side current-shunt monitor that allows an external reference to be used to measure current flowing in both directions through the internal current-sensing resistor sensor. The integration of the precision current-sensing resistor provides calibration equivalent measurement accuracy with ultra-low temperature drift performance and ensures an optimized Kelvin layout for the sensing resistor is always obtained.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Express Module
PCIe-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
12.1" 1024 X 768 & 800 X 600, VGA/DVI Interface, Ultra Slim Open Frame Touch Monitor
IDS-3112
-
12.1" 1024 x 768 XGA, 800 x 600 SVGA panel with LED backlight for 20% power saving and environmental protection. -20°C~+60°C wide operating temperature support, 5-wires resistive touchscreen solution.
-
Product
PXI Vector Signal Analyzer
-
PXI Vector Signal Analyzers feature a wide frequency range, real-time signal analysis, and advanced signal processing. PXI Vector Signal Analyzers can perform measurements for a broad range of wireless technologies such as GSM, EDGE, WCDMA, LTE-Advance Pro, 5G, Wireless LAN, and Bluetooth. Select models also feature a LabVIEW-programmable FPGA that you can customize for advanced measurement applications. PXI Vector Signal Analyzers are ideal for microwave test, wireless test, RADAR test, spectral monitoring, software-defined radio (SDR), radio monitoring, interference detection, signal intelligence, and other applications.
-
Product
PCI Smart Bus Extenders
PCIEXT-64 - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
Product
SMART III RF Moisture Sensor
-
Results are continuous, instantaneous and non-destructive. Used among diverse applications including gypsum, powdered and granular materials, agriculture and wood products. Monitor required to complete system. (Sold Separately): SMART III RF LED Screen OR Touch Screen
-
Product
15.6" Touch Computer
UTC-315K
-
15.6" Touch Computer with Intel® N97/ Core™ i3-N305 Processors. Low power and fanless system design. Built in Intel® Atom N97/ Core™ i3-N305 processors. 15.6" monitor with 16:9 widescreen display. Front panel IP65 compliant. Supports both landscape and portrait screen orientations.
-
Product
Bus Controller
CPCI-1553-1
-
Single or dual UTMC 1553 Summit Controller, Bus controller, Remote terminal, Bus monitor modes.
-
Product
LED Driver Aging Rack
LEDRACK-100W192P
-
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
Product
Load Cell Tester
-
Xiamen Elane Electronics Company, Ltd
Large six-digit LED display < Easy to use and small in size < Accuracy of 0.005%FS/10ppm < 2 channels CH0 : -12mV/V~+12mV/V, with resolution 0.1uV/V CH1 : -1.6mV/V~+4.8mV/V, with resolution 0.01uV/V < Four user selectable output units (N, kgf, lbf and mv/V) < Peak Hold function to capture and holding the peak value for the immediate or later reference < Clear key to clear the peak value < Presence of tare key and foot switch to zero the display (tare function) < Great for monitoring and testing load cell characteristics (repeatability, linearity, creeping, temperature drift, etc
-
Product
Software
-
From embedded low-level essentials like built-in-test and operating system board support packages, to advanced middleware for board and system health monitoring, image processing and autonomy support, Abaco's ever-growing software suite gives developers what they need to implement their application solutions.
-
Product
Continuous Emission Monitoring Systems
-
TML has more than 50 years' experience designing, manufacturing, and supporting continuous emission monitoring systems (CEMS). We have a team of experienced CEMS air quality experts that will thoroughly review your process and operating permit and recommend the most cost effective and reliable solution for monitoring the gases of interest. TML's continuous emission monitoring systems are based on rugged, reliable equipment manufactured to exact standards. The result is products and systems with some of the highest mean time between failure rates in the industry. Whether it's a standard or custom solution, we stand behind our products 110%, guarantee CEMS certification, at least 95% uptime, replacement parts, and 24 x 7 support. We offer a total CEMS solution including data acquisition software for recordkeeping and reporting, lower cost of ownership, superior product reliability and designed for simple and easy maintenance.
-
Product
7" Flat-Fronted Touch IP67 Monitor
IDP31-070W
-
7" flat-fronted touch IP67 monitor. Support wide operating temperatures, flat surface, and rugged glass fronted for a contemporary outlook and IK08.
-
Product
Purpose Built Network Packet Brokers
-
Garland Technology’s Purpose Built Network Packet Brokers (NPBs) are devices that provide access to network traffic from multiple links, helping to centralize and improve efficiencies by sharing packets between the monitoring and security appliances. Additional NPB features include filtering, aggregating, regenerating, and load balancing.
-
Product
Software
-
Interact with multiple networks, perform diagnostics, node/ECU simulation, data acquisition, automated testing, memory edit or calibration, and vehicle network bus monitoring.
-
Product
PATTERN GENERATOR
PG-68
-
The model PG-68 pattern generator generates a wide variety of test signals and patterns for testing, servicing, and adjustment of television, computer monitors, and video equipment.
-
Product
Task Sequencing and Automated Process Control
T-Zero
-
Command and Control Technologies Inc.
T-Zero is a unique process control program that facilitates automated design and execution of command, control, test, and monitoring activities. It features visualization of the operations process itself coupled with automated coordination of group activities. The software provides a visual, role-based interactive timeline built on the real-time data processing power of the Command and Control Toolkit™ (CCTK). T-Zero is the perfect automation solution for labor -intensive procedural activities: improving process organization, repeatability, and freeing operations staff from tedious task details to focus on strategic operational objectives.
-
Product
Static Measurement
-
Fraser Anti-Static Techniques Ltd
Accurate and versatile static measurement tools to investigate, monitor and maintain safety and productivity.
-
Product
Temperature Sensors and Temperature Controls
-
KOBOLD manufactures a variety of instruments for temperature monitoring and temperature measurement, such as temperature switches, including thermal reed temperature switches and temperature switches for liquids, temperature gauges, temperature transmitters, temperature sensors and temperature probes.
-
Product
Digital Pressure Gage
DPGW
-
The Series DPGW is the only economic digital pressure gage for liquids with the ability to select engineering units on the market. With its 1% accuracy and digital push-button zero, the DPGW is the perfect choice for digitally monitoring the pressures of air and compatible liquids and gases.
-
Product
Electrical SCADA Monitoring
-
Model-driven SCADA & Monitoring provides an intuitive real-time visualization and analyses platform via intelligent graphical user interface, one-line diagram, geospatial view, and digital dashboards.
-
Product
Resets And Voltage Detectors
-
ST’s reset and voltage detector ICs provide basic voltage monitoring (low-voltage detect POR-LVD function) and reset timing for power-on resets. These devices offer:
-
Product
High Range UV Fluorescence SO2 Analyzer
Model N100H
-
Teledyne Advanced Pollution Instrumentation
The Model N100H instrument uses the proven UV fluorescence principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of high range SO2 gas. The instrument includes interferent rejection, providing a simple and precise solution for a broad range of continuous emission monitoring systems (CEMS) and stack testing applications.
-
Product
Slow Speed Switch
SS110
-
Features• Works with remote/external pulse frequency output sensor (NPN, PNP)• Setpoint ranges: 0.01-0.99 & 0.1-9.9 rpm• SPDT relay output• Monitors speeds down to 100 min. per rev• Dial-in calibration does not require power• Built-in start delay• DIN rail mounting simplifies installation• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options
-
Product
Off-Line Base Test Platforms
-
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
