Waveguides
guide the propagation of electromagnetic, light or sound waves.
See Also: Millimeter Waveguides, Optical Waveguides
-
Product
Waveguide Power Sensor
R8486D
-
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 26.5 GHz to 40 GHz Diode power sensing element
-
Product
Waveguide Harmonic Mixer, 40 to 60 GHz
11970U
-
The Keysight 11970U waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.
-
Product
Fail Safe Waveguide Switches
-
Waveguide switches enable very rapid switching between two RF channels. Fail Safe Waveguide Switches return to the de-energized position when the power is disconnected and requires a small holding current in the energized position. All models have low VSWR and high power handling capacity. They withstand the full power rating of the waveguide and most models can be pressurized to 0.2 MPa (2 ATO) for high peak power applications.
-
-
Product
60 GHz Development System
PEM009
-
The Pasternack / Vubiq 60 GHz development system provides rapid evaluation of Pasternack’s 60 GHz waveguide modules for quick prototyping for millimeter wave wireless system development. This high speed wireless 60 GHz developer kit is created from a partnership between Pasternack and Vubiq (pronounced “View-bik”), an industry expert in designing 60 GHz RF systems. Our 60 GHz wireless development systems make it easy to design new products and applications in the emerging unlicensed millimeter wave ISM V band.
-
Product
Frequency Extension Heads for Vector Network Analyzers
FEV
-
These frequency extension modules connect to your existing test ports and leverage the inherent microwave network analyzer’s performance and features to display full port S-parameters: Two measurement architecture available: 1-path/2-port and fully reversing 2 port. Waveguide calibration kits are available as separate accessories.
-
Product
Fixed Attenuator (Waveguide)
-
Fixed waveguide attenuator in a variety of freuqencies, power levels and attenation values.
-
Product
Waveguide Twists
-
Waveguide twists and bent types of waveguides are used extensively in electromagnetic devices. Twist waveguides are used to change the polarity of the fields. Waveguide twist VSWR is as low. Both 45° and 90° waveguide twists are available. The 45° versions being available in both right hand and left hand twist configurations.View more Twist Waveguides
-
Product
Solid State Power Amplifier Module
SSPA
-
Macom Technology Solutions Holdings Inc.
MACOM’s Solid State Power Amplifier (SSPA) and waveguide module product portfolio leverages our world class MMIC technology and system design expertise for high performance Industrial, Aerospace, Defense, and Communications applications. Our SSPA modules feature up to 16 power-combined MMICs in a single module and we can power-combine multiple modules up to 100GHz featuring either coaxial or waveguide interfaces.
-
Product
Double Ridged Waveguide Horn
DRH18–E
-
Frequency range: 1 GHz -18 GHz VSWR (max / AVG): < 3:1 / 1.35:1Impedance: 50 O (Ohm)Connector: SMA female / N femalePower (CW / Peak): 50 W / 100 W
-
-
Product
Double Ridged Waveguide Horn
DRH370
-
Frequency range: 370 MHz - 6 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 350W / 500 W
-
Product
Variable Attenuator
VAXE
-
The VAXE Variable Attenuators are waveguide components for tunable signal leveling or reflection compensation in waveguide networks. The Attenuators consist of waveguide section with a resistive film evaporated on the mica surface. The Attenuators has 0 ÷30 dB minimum attenuation range. The VAXE Attenuators are available in four waveguide bands between 33 GHz and 170 GHz.
-
Product
Flexible Waveguide
-
Flexible waveguide sections to connect waveguide comopoents and enable different mechancial placements
-
Product
Millimeter-Wave Noise Source, Q-band, 33 To 50 GHz
Q347B
-
The Q347B waveguide noise source (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices...
-
Product
Double Ridged Waveguide Horn
DRH10
-
Frequency range: 740 MHz - 10.5 GHz VSWR (MAX): < 1.8:1Impedance: 50 O (Ohm)Connector: N femalePower (CW / Peak): 150 W / 250 W
-
Product
Coaxial Waveguide Adapter, APC-7, 8.2 to 12.4 GHz
X281C
-
The Keysight X281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
RF Coaxial Probes & Probe Positioner
-
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
Product
Spot-Focusing Lens Antennas
-
The antenna employs a low loss lens to offer excellent aperture efficiency at 105.96 GHz. The lens antenna is equipped with a standard WR-10 waveguide and UG-387/U-M flange as its input port. It supports linear polarized waveforms.
-
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
Waveguide Duplexer
-
RF Lambda’s waveguide duplexers are used to combine two frequencies onto a common waveguide. They offer high isolation and low insertion and come in a variety of frequencies. Hermetically sealed options are available upon request.
-
Product
Double Ridged Waveguide Horn
QRH400
-
Frequency range: 400 MHz - 6 GHz VSWR (max): < 2.3 :1Impedance: 50 O (Ohm)Connector: 2xN female Power (CW / Peak): 350 W / 350 W
-
Product
Waveguide Harmonic Mixer (smart mixer), 50 to 75 GHz
M1971V
-
Keysight M1971V 50 to 75 GHz waveguide harmonic mixer is an un-preselected mixer that provides a complete solution for wideband millimeter-wave signal analysis of more than 2 GHz with X-Series signal analyzers. Embedded smart features help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
Product
Waveguide To Coax Adaptors
-
The transitions from waveguide to coaxial line (SMA connector type) are offered up to 110 GHz.
-
Product
Waveguide Bend
DWG8-WR-2C36.5-2561
-
Waveguide E-Plan Bend, Frequency 325~500GHz, VSWR 1.3:1, FUGP Flange
-
Product
Double Ridged Waveguide Horn
QRH300
-
Frequency range: 300 MHz - 4.5 GHz VSWR (max): < 2.2 :1Impedance: 50 O (Ohm)Connector: 2xN female Power (CW / Peak): 400 W / 750 W
-
Product
60 GHz Noise Figure Test Set
-
The Noisecom 60 GHz Noise Figure test set has 4 separate systems designed to perform Y-factor noise figure measurements using a high performance Spectrum Analyzer or a dedicated receiver. Each system contains a highly stable V-band noise source, isolator(s), optional waveguide to coaxial transitions and an optional pre-amplifier for use with a spectrum analyzer. The two standard calibration tables have ENR data points at 1 GHz intervals.* System ENR is measured before the DUT connector and at the final output stage allowing for pre-test calibration of the system.
-
Product
Double Ridged Waveguide Horn
H-A50
-
Frequency range: 33 GHz - 50 GHz VSWR (max): < 1.35 :1Impedance: 50 O (Ohm)Connector: 2.4 female Power (CW / Peak): 10 W / 20 W
-
Product
E-Band Signal Analysis Reference Solution
-
The E-band signal analysis reference solution provides an effective measurement solution for today’s wideband signals as well as emerging communications standards. With the M1971E waveguide harmonic mixer, which provides a 55 to 90 GHz input; Keysight oscilloscopes, which provide excellent signal integrity; and the powerful 89600 VSA software, you have a high-quality wideband measurement solution. A simple user interface also provides integrated mixer setup, correction and LO optimization, allowing for accurate measurements.
