Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
Product
AC Calibration Standard
1U647-001
-
The 1U647-001 is a low cost calibration standard used to determine if a 1U632-100 or a 1U663-100 DMU requires factory calibration. Its portability makes it ideal for field-testing. The standard generates signals that simulate the aircraft’s resolvers, rotary variable transformers (RVTs), and linear variable displacement transformers (LVDTs). The unit also generates a pulse width modulated (PWM) signal, and routes the output of an ARINC 429 source to the different DMU input channels. The calibration standard connects directly to the DMU and replaces the output signals of an active extender card. Discrete switch settings simplify testing. The unit is housed in a rugged aluminum case.
-
Product
Isolated Digital Input/Output Cards
PCI-IIRO-8 and PCI-IIRO-16
-
The PCI-IIRO-8 and PCI-IIRO-16 are low-cost, half-size cards that provide isolated input and output for PCI-Bus computers. The cards have eight or sixteen optically-isolated digital inputs for AC or DC control signals and eight or sixteen electro-mechanical relay outputs. PCI-IIRO-8 occupies four consecutive eight-bit registers in I/O space. PCI-IIRO-16 occupies eight consecutive eight-bit registers in I/O space.
-
Product
BERT Measurement Solutions
-
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 18GHz, 50Ω, SMA, Terminated, Remote Mount
40-785C-422-TE
Multiplexer Module
The 40-785C-422-TE (PXI) and 42-785C-422-TE (PXIe) are dual SP4T 18GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PCI High Density Matrix, Single 22x4 2-Pole
50-510A-022
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
InfiniiMax III+ Series Probe Amplifier, 4 GHz
N2830A
Amplifier
The N2830A Series InfiniiMax III+ probing system is the next generation of InfiniiMax probing, greatly expanding the measurement capability and usability of a probe capable of measuring all components of a differential signal. The built-in InfiniiMode technology allows customers to switch differential, single-ended, and common mode without adjusting probe tip connections.
-
Product
Oxygen Sensor
KS60051
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Signal Switching
SMP/SMIP Series
-
VTI's SMIP™ signal switching series revolutionized the automated signal switching marketplace by providing a level of modularity, density, and performance for the VXIbus platform that was unprecedented.
-
Product
Sound Source And Power Amplifier
-
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
-
Product
Pulse Generation Measurement Board
MS 1806
-
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
AVoIP Products - 4K @60Hz
-
AVoIP encoders and decoders for HDMI, audio, R232, IR, and USB signals as well as a controller for controlling and managing JPEG 2000 OP streams within an ethernet environment.
-
Product
Test FMC Mezzanine Module
TFMC900
-
The TFMC900 is an FMC (FPGA Mezzanine Card) Mezzanine Module designed to test ANSI/VITA 57.1 FMC Carriers during development or series production. Additionally, it offers the possibility to realise various I/O solutions for connected FMC Carriers. Interconnection of the High Pin Count FMC Connector signals can be verified by JTAG and by functional tests. A loop-back of the 10 multi-gigabit transceiver interfaces allows interconnection checks for the high-speed serial interfaces.
-
Product
Function Generators
-
Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM . 16bit digital arbitrary wave (TTL level) DARB. 16th Harmonic Generation Function. Protocol output: I2C, SPI, UART (TTL level). 8 Inch high-resolution TFT color LCD,WVGA(800×480). Standard interface: USB Host, USB Device, LAN, 10MHz clock source input/output. Frequency sweep and burst output. Easy-to-use multi-functional knob and numeric keypad
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 3 GHz, 50 Ω, N-Type, Terminated, Remote Mount, Failsafe
42-785C-561-TE
Multiplexer Module
The 40-785C-561-TE (PXI) and 42-785C-561-TE (PXIe) are single failsafe SP6T 3 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
3 GHz, 4 Channel Programmable Delay Line
QPADL3
-
The QPADL3 is a programmable delay line instrument with 4 independent channels designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 3 GHz.
-
Product
PSG RF Analog Signal Generator, 100 kHz to 9 GHz
E8663D
Signal Generator
Tackle demanding radar & satcom measurements with metrology-grade performance, including high output power & superior level accuracyUse as an ideal reference in phase noise test systems or for analog-to-digital converter testing with the lowest phase noise in a commercial sourceCharacterize devices & circuits by adding AM, FM, M & pulse modulation to your signalImprove existing test system performance: E8663D is built on the outstanding legacy of the 8663A & is fully code compatible
-
Product
Multifunction Instrument for Education and Training
LabXplorer
-
LabXplorer turns your desktop, laptop, tablet or smart phone into a powerful, multifunction test and measurement instrument for a wide range of applications. Instruments, whatever you need, are at your fingertips. LabXplorer provides multimeter, oscilloscope, spectrum analyzer, logic analyzer, programmable analog and digital signal generator, impedance analyzer and also measures characteristics of passive electronic components and semiconductor devices.
-
Product
IP VIDEO MARGIN TESTER
IPMT-3
-
The IPMT-3 is a precision attenuator used to test IP video systems to insure that you have an adequate digital signal margin. Digital signal margin is the amount of signal level above the digital cliff that you have in your system to prevent a picture failure from occurring. IP cameras will give you a perfect picture until the network cable loss reaches beyond the minimum allowable signal level and then you suddenly get no picture at all. This effect is called the digital cliff, because like walking off of a cliff, everything is great till you take the last step off the edge and then all is lost.
-
Product
6 Channel Function Generator / Flow Simulator
DP-cPCI-2601
-
DP-cPCI-2601 is a 6 Channel 2MS/s Waveform Generator with high frequency performance, versatility and compact size in an economical cPCI bus format. Signal output in the range of 10 mHz to 5 KHz with 14 bit vertical resolution makes this single slot, 6U-sized cPCI card a powerful solution to meet most demanding test stimulus.DP-cPCI-2601 uses Direct Digital Synthesis (DDS) technique to generate stable and accurate output waveforms down to 0.01 Hz resolution. DP-cPCI-2601 offers Sine, Square, Ramp, Triangle, Pulse as built-in wave shapes and user defined arbitrary waveform.DP-cPCI-2601 can frequency sweep any of its function outputs. User can sweep upwards using linear sweeps.
-
Product
Digitizers
2745 Family
-
The 2745 Digitizer is a 64-channel digital signal processor for radiation detectors available in VME64 (V2745), VME64X (VX2745), and Desktop (DT2745) form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others. The 2745 can perform pulse height measurements (PHA), constant fraction timing (CFD), charge integration (QDC) and pulse shape discrimination (PSD) independently for each of the 64 channels.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 2-Bank 6GHz SMA
60-802-002
Multiplexer Module
The 60-802-002 is a 4-channel, 2-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers.
-
Product
High Performance Data Acquisition
PMC-AD8
-
The PMC-AD8 module provides a high performance dataacquisition subsystem. There are (8) eight 200 KSPSADC’s for maximum performance. The Local DSP can beused to simply move data samples to the PMCbus or canprovide processing functions such as limit checking, FFT’s,digital filtering, etc. Software can be downloaded to theDSP via the PMC interface. Instrumentation amplifiersprovide over-voltage protection and gain on a per channelbasis. The PMC-AD8 can also accept external scan andtrigger signals from a front panel connector.
-
Product
Sensor Amplifier
UVM-SB
-
This is the relay amplifier box for the multi-point type UV monitors. Received UV light intensity is converted to electric signal for transmission. This allows distance between the light receiving inlet and the controller to 10 meters maximum.
-
Product
PXI MUX 2 Bank, 32 Channel Screened 1 Pole
40-610-021-S-2/32/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Automation
ZETLAB Formula
-
ZETLAB Formula is a program used for mathematical operations with signals, signal filtration, and parameters measurements, producing signals with various shapes. ZETLAB Formula is a virtual measuring tool allowing to perform arithmetical and logical operations and filtration of constant data flows received from ADC and DAC modules and virtual channels in real-time mode. In the post-processing mode, it is possible to perform various operations with the files created by means of “Signals recording” program.
-
Product
LXI Microwave Multiplexer, SP6T, 13-Bank, 26.5GHz, 50Ω, SMA, Terminated
60-800-313
Multiplexer Module
Our 60-800-313 is a 13 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Calibration And Verification Instruments
-
The system of automatic calibration and verification consists of a computer of the operator's workplace and a control controller with a calibrator connected to it and a verified device. The device under test can have 4 to 16 working channels with a complicated circuit for connecting different types of signals: voltage, current, thermocouples, thermoresistance. The system allows a change in the set of operating ranges during calibration and calibration. The software development system used the LabVIEW development environment with the Real-Time module.
-
Product
NIST Calibration for D400A-AT
D400A-AT-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 50GHz, 50Ω, SMA-2.4
40-785C-452-TE
Multiplexer Module
The 40-785C-452-TE (PXI) and 42-785C-452-TE (PXIe) are dual SP4T 50GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Emergency/Panic Button
ENVIROMUX-EBS
-
Sends activation signal when button is pressed. For normally closed or normally open circuit connections. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft (305 m). Dimensions WxDxH: 1.7x2.9x4.6 in (43x74x117 mm). Regulatory approvals: RoHS.
