Filter Results By:
Products
Applications
Manufacturers
Hall Effect
a measurable transverse voltage which occurs when current flows through a conductor in a magnetic field.
-
product
Hall Effect Probes
Magnetic Instrumentation manufactures Hall Effect Probes in a wide range of styles and sizes. Probes are supplied with magnetic, electrical, temperature stability and calibration data for each measurement range.
-
product
Hall Effect Thickness Gage
Magna-Mike 8600
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
product
Hall Effect Measurement Equipment
HEM
The physical quantity of Hall Coefficient, Hall Mobility and Carrier Density etc. can be investigated by measuring at room temperature voltage occurred perpendicularly to the both magnetic field and constant-current when flowing constant-current perpendicularly to magnetic field from current source while applying magnetic field to sample set at the center of magnetic field of magnet.
-
product
Rotary Hall Effect Sensor
The output of the Rotary Hall-effect sensor is a voltage which changes in direct proportion to the shaft angle. The sensor is non-contact, using Hall elements to determine the angle of a magnet. The magnet is either mounted in a shaft integral to the sensor or can be mounted externally to the sensor.
-
product
Hall Effect Proximity Switches/Sensors
ChenYang Technologies GmbH & Co. KG
A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.
-
product
Hall Effect Systems
The MeasureReady™ measurement controller is a revolutionary, all-in-one Hall analysis instrument that delivers significantly higher levels of precision, speed, and convenience to researchers involved in the study of electronic materials.
-
product
Hall Effect Gear Tooth Sensors and Custom-Made Target Wheels
ChenYang Technologies GmbH & Co. KG
ChenYang Technologies GmbH & Co. KG supplies various kinds of Hall Effect Gear Tooth sensors (CYGTS101DC, CYGTS99, CYGTS211, CYGTS212, CYGTS99-198 etc.) for speed measurement with applications to machines, equipments, motorcycles, automobile industry and instruments etc. We are specialised in design, development and production of Hall-effect sensors and can offer also custom Hall sensors for your special applications.
-
product
Hall Effect Measurement system
HMS-5500
Variable temp : 80K ~ 350K (model# : AMP55T ) - HMS-5500 can be compatibly used with both low temp magnet kit (model# :AMP55T) and high temp magnet kit (model#: AHT55T5, upto 500dC) - Below image is to show model# HMS-5500 + AMP55T, for low temp.
-
product
Hall Effect Portable Gauss-Meters
300 Series
Integrity Design and Reseach Corp.
Typical Applications include Measurements of the Earth's field vectors, Air shipment inspection, Mapping and recording field perturbations, Magnet classification, Analysis of magnetic circuitry and components, Magnetic Resonance Imaging (MRI) and Measuring residual fields.
-
product
Hall Effect DC Current Sensor
CYHCT-L20K
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-L20K is based on open loop principle and designed with a high galvanic isolationbetween primary conductor and secondary circuit. It can be used for measurement of DC current, DCpulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
product
Closed Loop Hall Effect Current Sensors/Transducers
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor
-
product
Hall Effect Measurement system
HMS-5300
Variable temp : 80K ~ 350K (model#: AMP55T ) - HMS-5300 can be compatibly used with both low temp magnet kit (model# : AMP55T) and high temp magnet kit (model# : AHT55T3, upto 300dC). - Below image is to show model# HMS-5300 + AMP55T, for low temp.
-
product
Current Probe With Hall Effect Technology
CP 35
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
product
Hall Effect Sensor
907 XP (Explosion Proof)
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
product
Hall Effect DC Current Sensor
CYHCT-WS3
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
product
Hall Effect Sensors
The Mors Smitt transducers are used to measure high currents in rolling stock and trackside applications. High currents are converted linearly to low power signals.
-
product
Hall Effect Sensor Elements/ICs
ChenYang Technologies GmbH & Co. KG
is a sophisticated Hall Effect Gear Tooth IC featuring an on-chip 12-bit A/DConverter and logic that acts as a digital sample and hold circuit. A separate 6-bit D/A converterprovides a fixed hysteresis. The sensor does not have a chopper delay. It uses a single Hall platewhich is immune to rotary alignment problems.
-
product
Super high temperature hall effect measurement system
Super high temperature hall effect measurement system that is useful to flow gas into chamber with sample. - Newly developed furnace that makes it possible to increase over 800 and use for measuring hall effect. - Gas flow control system in order to flow various gas. - Sample holder for high temperature. (keep the good contact on 800) - High Temperature control system (DC power) On condition of specific temperature with gas flow , new semiconductor materials have been developed to see electrical property's change.
-
product
Hall Effect Sensors
906
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Bi-directional option 906B
-
product
Hall Effect Measurement system
HMS-3300
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
product
Hall Effect Sensors
A new range of sensors based on closed loop hall effect technology, for measuring and monitoring of e.g. secondary transformer overload or shortcircuit detection, DC link from ground fault and overload, motor overload.
-
product
Gaussmeter
DX-101
DX-101 Gaussmeter is based on the Hall effect magnetic field strength of the latest developments in instrumentation, the design of desktop-type Gauss meter. Maximum range 330.0mT and 3000mT two tranches, the minimum basic error of 1.0%. Test probe connectors is imported, stable and reliable connection.
-
product
Hall Effect Speed Sensors
SPECTEC Innovative Sensor Solutions
SPECTEC zero speed Hall effect gear tooth sensors are used in industrial applications to determine shaft or gear speed or direction by detecting fluctuations in the magnetic field. The Hall effect technology fulfills a wide array of applications due to a Hall effect sensor's ability to detect zero speed and the quadrature sensor's ability to detect direction change. The Hall effect gear tooth sensor's digital output is easily read by computers, motion control devices, position monitors and digital to analog converters. Intrinsically Safe zero speed sensors are available for various applications.
-
product
Current Probe For Non-Intrusive Measurement Of AC, DC, And Waveform Currents
CP 305
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
product
CAN Sensor/ Interface
Current
Reach Technologies’ CAN Current Sensors sense and digitize conductor current for collection via CAN. The module is ideal for conveniently adding current data to a distributed CAN network. The CAN Current Sensor is configurable via J1939 or CANopen stacks, and are available in Hall Effect and shunt variants.
-
product
Speed Sensors
Series 18
Features • Square-wave pulse frequency output • NPN or PNP output options • Single channel or bi-directional options • 5-24 VDC powered • Hall Effect or Magnetoresistive sensing options • Standard and wide temperature options • Rugged M18x1 stainless steel sensor housing (all models) • Four housing options • All sensors are epoxy filled and sealed against liquids and dusts • Works with Electro-Sensors magnetic pulser discs/wraps
-
product
Non Contacting Rotary Position Sensors
We offer a comprehensive range of Hall Effect Non Contacting Position Sensors, from the World leading suppliers. Our range includes both Non contacting and Non touching Rotary Position Sensors.
-
product
Closed Loop Hall AC/DC Current Sensor
CYHCS-D8
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current in the carrying conductor.
-
product
Rotary Position Sensors For Motorsport
Variohm offer a range of Rotary Position Sensors For Motorsport including rotary potentiometers and hall effect sensors. They are suitable for use in Morotsport application such as pedal, steering and gearbox applications.
