Adapters
Interfaces that facilitate interconnect between two dissimilar elements.
-
Product
Test Fixture Adapters for In-Circuit Test Fixtures
-
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
Product
Adapter, 2.4 mm (m) to 3.5 mm (m), DC to 26.5 GHz
11901A
-
The Keysight 11901A is a 2.4 mm male to 3.5 mm male metrology-grade adapter with dc to 26.5 GHz operation.
-
Product
Adapter/Stainless Steel
WADP-24F35F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
NI-6581B, 100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO
783887-01
-
100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO—The NI-6581B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581B can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
QFP-to-PGA EIAJ 208-Position, 0.0197 [0.50] Pitch Adaptor
96-208M50
-
QFP to PGA Adapter for EIAJ 208 Position, .0197 [.50] Pitch. Reduce costs by using less expensive QFP packages to replace PGA footprints in existing designs. Pins are mechanically fastened and soldered to board using Aries patented process, creating a reliable electrical connection and rugged contact.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138200
-
Primary mating contact 610138118. (May mate with other Male Adapter and ITA contacts, as well.)
-
-
Product
Wireless Airflow Temperature Humidity Adapter
DTHA2
-
UEi Test & Measurement Instruments
Airflow Temperature Humidity Adapter with Free App
-
Product
XMC-to-PCI Express Adapter
4821
-
The XMC2PCE is a passive 8X XMC to PCI express carrier card which permits the use of XMC cards in PC style PCI express 1X, 2X, 4X, 8X or 16X motherboard slots.
-
Product
Cables
-
Adapter Cables connect your Spectrum card or instrument with your device under test, your sensor, your transmitter or receiver, your external machine, your prototype equipment or simply with a probe for measuring. To fulfill a lot of different requirements Spectrum is offering adapter cables between different types of connections and with different length. These adapter cables are manufactured for Spectrum following Spectrum's specification.
-
Product
PCIe Adapter for XMC
PCIe8LXMCX2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIe8LXMCX2´s two positions a PrXMC can be matched with another XMC to make a high bandwidth processing node. The PrXMC can communicate with the host for set-up, and then use the switch to interconnect with the special purpose IO card.
-
Product
Coaxial Adapter, 3.5 mm (m) to 3.5 mm (m), DC to 26.5 GHz
83059A
-
The Keysight 83059A instrument-grade 3.5-mm male coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
-
Product
DH Series QuickLink Adapter, 8 GHz BW
DH-QL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
2.92mm to ProBus Probe Adapter
L2.92A-PBUS
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PBUS adapter converts the 2.92mm interface to a ProBus interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi from high-impedance ZS active probes to the high-bandwidth WaveLink differential probing system. Full probe power and control is provided through a built-in LEMO interface.
-
-
Product
I2C High Speed Interface for USB
Tracii XL 2.0
-
telos EDV Systementwicklung GmbH
Tracii XL 2.0 is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 3.33 Mbit/s. Additionally Tracii XL 2.0 can work as an I2C monitor.
-
-
Product
Interface Test Adapter
ITA
-
Circuit Check is focused on the military and aerospace market. Our solutions are delivered according to a rigorous set of test requirements and quality metrics. The Circuit Check staff of engineers follow a defined Project Management process to control the project deliverables,manage the scope, and meet the quality needs for in-field serviceability and test system longevity.
-
Product
NI-5783, 40 MHz Bandwidth Transceiver Adapter Module for FlexRIO
784364-01
-
The NI‑5783 has DC‑coupled inputs with two variants: an elliptic filter variant optimized for frequency-domain applications and a Butterworth filter variant optimized for time-domain applications. The NI‑5783 is particularly well suited for applications in software defined radio, electronic warfare, high-performance machine control, and medical imaging. The NI‑5783 is compatible only with the PXI FPGA Module for FlexRIO modules that have a Kintex‑7 FPGA and the stand-alone Controller for FlexRIO.
-
Product
PCIe Gen 4.0 RAID Adapter
MegaRAID 9560-8i
-
The MegaRAID 9500 series is the industry’s first PCIe Gen 4.0 RAID adapter family, offering PCIe Gen 4.0 host and storage interfaces. The MegaRAID 9560-8i adapter, based on the SAS3908 high-port count PCIe 4.0 x8 RAID-on-Chip (RoC), delivers twice the performance of previous generations.
-
Product
Waveguide to Coaxial Adapter
D8-AWC84SK-1296
-
Waveguide to Coaxial Adapter, Frequency 6570~9990MHz, 50W, Rect. Waveguide FBP84, SMA Female
-
Product
Test Adapter
PMC-UNIV-TEST
-
PCI adapter for PMC with options for PCI and PMC Stack Pass through connections
-
Product
Tap Adapter
-
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
Product
Transceiver Adapter Module For FlexRIO
-
Transceiver Adapter Modules for FlexRIO feature multiple inputs, outputs, and digital I/O lines for applications that require the acquisition and generation of IF or baseband signals with in‐line, real‐time processing. Example applications include RF modulation and demodulation, channel emulation, signals intelligence, real‐time spectrum analysis, and software defined radio (SDR). Transceiver Adapter Modules also provide digital I/O capability for interfacing with external hardware.
-
Product
Serial Digital Interface
Model 2363
-
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* RS-232 and RS-485 Serial IO.* 1 U high rack mount kit mounts one or two 2363s* Includes US 115 VAC Power Adapter
-
-
Product
SSOP-to-DIP Adaptor
Series 351000
-
SSOP IC to DIP Adapter. Allows the use of .65mm pitch surface mount ICs in thru-hole designs. Ideal for prototyping and testing/evaluating SSOP ICs. Adapter can be cut to smaller sizes by end user. Consult factory for panelized form or for mounting of consigned ICs.
-
Product
Ethernet Adapters
-
Advantech's family of Network Interface Cards gives customers access to a full range of 10GbE, 25GbE, 40GbE and 100GbE interfaces.
