Attenuators
Reduces the amplitude of a signal without appreciably distorting its waveform.
See Also: Filters, Circulators
-
Product
Attenuators
-
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
Product
Fixed Attenuators
-
Macom Technology Solutions Holdings Inc.
MACOM offers fixed attenuator bare die to be used in chip and wire assemblies. These products offer excellent return loss and flat attenuation from DC to 50 GHz. Attenuation values range from 0 to 20 dB.
-
Product
Coaxial Attenuators Set
11582A
Attenuator
The Keysight 11582A contains a set of four 8491B attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8491B are type-N connectors with a maximum frequency of 18 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
-
Product
Programmable RF Attenuators
-
The AD-USB R3 is AdauraTech’s latest design in the AD-USB series of programmable RF attenuators. Combining all the best features of the previous models, the R3 is the new series flag ship. With a completely custom machine aluminum enclosure, the R3 boasts 95dB of attenuation. The addition of Ethernet allows EASY implementation into the most modern of test setups by allowing network control via HTTP web interface or direct Telnet while the USB port powers the device and allows for serial communication.
-
Product
Attenuators
-
Teledyne RF & Microwave offers a variety of analog controlled attenuators operating over a 10MHz to 26GHz range. With many units operating over many octaves, switching speeds less than 100nS and attenuation control up to 50dB, RF&M has a product that meets your demanding needs.
-
-
-
Product
Voltage Variable Attenuators
-
Voltage variable attenuators (VVAs) that offer up to 60 dB of attenuation across a broad range of frequencies from 400 MHz to 18 GHz. These voltage variable attenuators are frequently used in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.
-
-
Product
Coaxial Attenuators Set
11583C
Attenuator
The Keysight 11583C contains a set of four 8493C attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8493C are APC-3.5 connectors with a maximum frequency of 26.5 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Telephone Attenuators & RFI Filters
-
Despite the growth in digital and fiber systems, many telephone companies still require basic line treatment products. Wilcom's hard-to-find line treatment products help the telecommunications industry deliver the performance the customer expects. Products include line powered amplifiers and RFI filters.
-
Product
Attenuators
-
The 01311 attenuator chip series is designed to achieve precision and tight flatness with an attenuation accuracy of ± 0.2 dB on our 1-10 dB pads and ± 0.3 dB on our 11-20 dB pads. SemiGen tests 100% of all attenuator chips prior to shipment to verify that they meet specifications.
-
Product
Coaxial Dynamics RF Attenuators
-
Coaxial Dynamics RF Attenuators offer a reliable and accurate method for reducing RF power levels. All of our designs dry convection cooled and can be used in any position.
-
-
Product
Coaxial Attenuators Set
11581A
Attenuator
The Keysight 11581A contains a set of four Keysight 8491A attenuators 3, 6, 10 and 20 dB with type-N connectors, furnished in a walnut accessory case. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Variable Optical Attenuators
Attenuator
Fast attenuation speed with low insertion loss and built-in power monitoring. Operates in fixed attenuation or constant output power modes and supports SMF, MMF and PMF.
-
Product
Attenuators
-
OZ Optics offers a broad range of both variable and fixed attenuators having key competitive advantages. All of our attenuators operate over the two standard wavelength bands, the C-Band and the L-Band. This wide wavelength range makes these components ideal for DWDM applications. Our attenuators are wavelength insensitive, which means they operate with minimal changes in attenuation when used in either the C-Band or the L-Band and exhibit low return loss. In addition, all of our attenuators have a wide attenuation range, which means they operate at a wide range of power levels. This is important as increased power levels are being used in newer optical systems.
-
Product
Fixed Attenuators
-
In circuits are used to lower voltage, dissipate power, and to improve impedance matching. In measuring signals, attenuator pads or adapters are used to lower the amplitude of the signal a known amount to enable measurements, or to protect the measuring device from signal levels that might damage it.
-
Product
Voltage Controlled Linearized Attenuators To 16 GHz
-
Pulsar's voltage controlled, PIN diode linearized attenuators are available from 0.25-16 GHz with attenuation ranges of 32 and 64 dB. Each model includes an integrated linearizer, and a driver that controls the attenuation level. This design results in transient free switching between attenuation levels as opposed to the spurious outputs that result when an attenuation value is switched either on or off by a direct digitally controlled attenuator. Transfer function is 8 dB / Volt.
-
Product
Digital Step Attenuators To 18 GHz
-
This family of digitally controlled switched bit attenuators have standard attenuation ranges of 32 dB and 64 dB, with 8 bits of resolution. LSB of 32 dB models is 0.125 dB, and for 64 dB models LSB is 0.250 dB. Attenuation level is obtained by 8 TTL control inputs.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
Chip-Type Attenuators
-
Panasonic Industrial Devices Sales Company of America
Chip-Type Attenuators for high-frequency signal attenuation, level adjustment or matching improvement.
-
Product
Fixed Attenuators
-
BroadWave attenuators reduce the strength of an RF signal without appreciable distortion of its waveform.
-
-
Product
Fixed Attenuators
DC to 220GHz
-
RF Attenuators are components that reduce the amplitude level of an incoming frequency signal. They are used to protect systems from receiving a signal with a power level that is too high to process. There are various types of fixed attenuators that can fit your engineering needs. Precision MMW will help you with the highest quality fixed attenuator products needs.View more Fixed Attenuators
-
Product
Step Attenuators
-
A stepped attenuator from Pasternack. Our BNC attenuator is a RF step attenuator design. This 50 Ohm manual step attenuator is precision manufactured to RF and microwave industry specifications.
-
Product
Variable Attenuators
-
Continuously variable attenuators from Pasternack are available in 50 Ohm impedance and with SMA connectors. SMA continuously variable attenuators have RF db attenuation values that range from 7 dB to 40 dB. The frequency range of our continuously variable attenuators is from 1 GHz to 18 GHz. This variable attenuator product line includes low to high power attenuators which have the power handling up to 5 Watts.Variable attenuators from Pasternack include female genders and can be bidirectional, depending on the power rating. Our continuously variable attenuators are manufactured to precise industry specifications and the bodies are constructed of. Pasternack commonly uses Pi attenuators or Pi pads for its continuously variable attenuator designs.
-
Product
Waveguide Tunable Attenuators
-
*Low Insetion Loss*Full Waveguide Band Coverage*Precise Adjustment*High Maximum Attenuation
-
Product
Variable Attenuators
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber offer optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there can be used in the digital system of communication devices (such as:PHD, SDH) and also in the system of adopting analog modulation (CATV).
