Filter Results By:
Products
Applications
Manufacturers
Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. AKA: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
- Pickering Interfaces Inc.
product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-D/10/8
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
High Performance Data Acquisition
CPCI-AD8
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8/16 can also accept external scan and trigger signals from a front panel connector.
-
product
USB Modular Simultaneous Sampling Multifunction Data Acquisition
U2500A Series
The Keysight U2500A Series USB simultaneous sampling multifunction data acquisition (DAQ) devices are high performance modules that comprise of three models U2531A, U2541A and U2542A. The U2500A Series provides up to four channels with 14-bit and 16-bit resolution. The U2531A can sample up to 2 MSa/s for each channel with resolution of 14 bits. While, the U2541A and U2542A can sample up to 250 KSa/s and 500KSa/s for each channel respectively with resolution of 16 bits.
-
product
IPS BEACON
The Flowserve IPS Beacon is a data acquisition, logging and visual alert device that monitors process pump health. Mounted atop the pump bearing housing, the intrinsically safe Beacon checks power-end vibration (x-y-z axis) and temperature against pre-set limits, logging this data with a time and date stamp when an alert situation occurs.
-
product
Vibration Condition Monitoring
PROTOR
PROTOR provides a complete hardware and software solution for vibration monitoring of rotating machines. Acquisition subsystems monitor the machinery and are networked to a central server. Realtime and historical data can be accessed on the server or remotely via a LAN, WAN or VPN. Data and reports are available in graphical and numerical forms.
-
product
OpenVPX Integrations
Sundance Multiprocessor Technology Ltd.
Listed below are our OpenVPX based COTS integrations.We have products with ADC, DAC, DAQ video etc.
-
product
PXI 2A Multiplexer, 1-Bank, 16-Channel 8-Pole
40-614-018
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Data Acquisition System
System 620/600
The Series 600 is NEFF's top-of-the-line data acquisition system providing the utmost in performance, accuracy and convenience. Featuring leading-edge technology and innovative design, Series 600 brings extensive automation and complete programmability to the testing laboratory.
-
product
WiFiScope WS6-DIFF + SureConnect: 1 GS/s 250MHz BW, 4 Channel, Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-DIFF-1000XMS-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
product
CAN + OBD Network Data Converter
NC2
Add Vehicle Network based Data Acquisition to your existing fleet data acquisition systems for under one thousand dollars with the NC2. Great for NVH Tachometer applications.
-
product
PXI MUX 1-Bank of 80 Channel 1-Pole
40-615-021-1/80/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
Camera Barrel Test System
BK8612
We designed the BK8612 2 Channel Noise Test System to provide noise and vibration testing for your digital camera barrel DC Motors. Because it is based on the BaKo BK2120B DAQ, it is capable of monitoring a microphone and an accelerometer concurrently to obtain data from the motor. Because you can change the parameters of functions and limits, it is versatile but still quick and easy to set up. In addition, you can look at data in real time and also store it for future analysis. Easy to use and set up, fast and accurate; if you need to maintain the quality of your camera barrel motors, this is the tester you want.
-
product
PXIe-6368, 16 AI (16-Bit, 2 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module
781058-01
PXIe, 16 AI (16-Bit, 2 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXIe‑6368 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6368 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Dual 16x2 1-Pole High-Density PXI Matrix Module
40-520-501
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
RC68-68, Ribbon Cable, 68 D-Type to 68 VHDCI Offset, 1 Meter
187252-01
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
product
External Measuring Systems
LAN, USB
An alternative for measuring cards integrated in a PC are external data acquisition systems from BMCM. In this case, sampled data are transmitted to the PC via the USB interface or the LAN network - perfect for mobile applications!
-
product
Acquisition Of 8 Displacement Transducers
APCI-3701-8
PCI interface to the 32-bit data bus Acquisition of 16 or 8 inductive displacement transducers (Half Bridge, LVDT) 8 or 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Compliance Test Software Measurement Server License
D9010AGGC
The D9010AGGC compliance test software license provides the capability to offload the measurements from the compliance test software running on an oscilloscope to one or multiple virtual machines or measurement servers. This allows you to perform continuous data acquisition and computation of tests result in parallel, reducing the overall test time.
-
product
Data Acquisition & Data Loggers
Has been designed to meet all test applications in production and research.
-
product
PXIe-6396, 8 AI (18-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
785927-01
PXIe, 8 AI (18-Bit, 14 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6396 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6396 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
12-bit, 100KHz, 8SE/4DIFF Isolated Analog Input Board
APCI-3001-8
8 single-ended or 4 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
product
CAN + OBD Network Data Converter
NC1
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
-
product
National Instruments System Integrator
Knowledge of all National Instruments platforms and its wide experience in using and integrating NI hardware (CompactRIO, sbRIO, PXI, CAN, DAQ, etc.) and software (LabWindows/CVI, LabView e TestStand), IPSES offers to its clients customized solutions and services, providing both technological and economic benefits.
-
product
Metallographic Analyzer
MDS-5000D
Wuxi Tianmu Instrument Technology Co., Ltd.
1) the Integrated T -shaped Mirror Design, PROVIDING Superior Stability 2) Low-position Front Operation, Ergonomic requirements . 3) 6V / 30W Adjustable Halogen LAMP, PROVIDING Ample Bright Lighting System . 4) 3/8 splitting of Tube The trinocular , Observation and photography can be carried out simultaneous 5) Low-position mechanical moving platform to quickly locate the image 6) Professional flat-field metallographic objective lens, providing good resolution and clear image 7) Polarization Detecting partial inserts, related polarized light observation mode 8 )Five-hole rotary disc type color filter, easy to operate and switch 9) Adjustable field of view diaphragm and aperture diaphragm, providing good contrast metallographic analysis software system CCD camera will The optical image from the microscope is converted into a video signal, and the Sample image under the microscope is input into the computer through the image acquisition card / digital camera, and the digital image is processed and measured by the software, and finally the image and the measurement result are printed. Back up images and measurement data. General system:General image processing functions: image acquisition, data backup, depth of field expansion, grain boundary reconstruction, image stitching, image calculation, filtering, Image annotation, image segmentation and processing, accurate printing. Professional analysis system: 1. Rating: based on inspection Standards, more than 200 software functional modules in more than 100 categories.
-
product
Antenna Training and Measuring System
The complete Antenna Training and Measuring System includes a set of 1 GHz antennas, a set of 10 GHz antennas, an RF Generator, a receiving system, and the Data Acquisition and Management Software for Antennas (LVDAM-ANT), a user-friendly software operating under the Microsoft® Windows™ environment. The receiving system consists of a rotating Antenna Positioner linked to a Data Acquisition Interface connected to the USB port of a personal computer.
-
product
Weather Stations (Paperless Recorder)
Is a data acquisition unit. It is designed for use with our ranges of meteorological sensors.
-
product
Data Acquisition System
Synergy Qb
The Synergy Qb offers the same Synergy input capabilities in a field rugged product offering IP51 environmental resistance against dust and water. This DC-operated system can acquire standalone to its internal low-power PC with solid state drive, or to an external PC via Ethernet.
-
product
IRIG Time Code Receiver & Generator for Computers (PCI Express)
TCR180PEX
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. The output format is independent from the incoming IRIG signal - a perfect solution to your IRIG conversion requirements. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device.
-
product
Flush Diaphragm Pressure Sensors
Honeywell Industrial Automation
For high-frequency pressure measurements or in applications with severe space limitations, Honeywell Sensotec offers subminiature flush diaphragm pressure sensors in ranges from 0100 psi to 020,000 psi (010 to 01,400 bar). All-welded, machined stainless steel sensing diaphragms ensure ruggedness. Bonded piezoresistive and metal foil strain gauges offer high reliability. Millivolt and optional high-level outputs are compatible with most data acquisition systems.
-
product
Terminal Block and SCSI-II 68 Pin Connector with 1 Meter Cable
U2901A
The Keysight U2901A is an accessory compatible and recommended to be used with the U2300A Series USB Modular Multifunction Data Acquisition and U2500A Series USB Modular Simultaneous Sampling Multifunction Data Acquisition. The pin-outs of the U2901A is dependent on the USB Data acquisition unit that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2901A is to be used with.
