Modulators
Are devices which varies a characteristic of a repetitious electrical or electromagnetic wave of less than infrared frequency in accordance with a characteristic of an arbitrarily varying information carrying signal.
-
Product
PXI Switch - 16-CH General-Purpose SPDT Relay Module
PXI-7901
Relay
ADLINK PXI-7901 is a general-purpose (GP) switch module implementing 16-CH independent single-pole double-throw (SPDT) relays (1 Form C). PXI-7901 can connect one input to one output and be used as signal switching and routing for measurement system or ATE. Thanks to its high switching capacity, PXI-7901 can also be used to turn on or turn off devices such as motors, fans, heaters, and lights. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7901, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
Product
Fiber Optic Loopback MTP
-
Anfkom International Co.,Limited
Anfkom can provide single mode and multimode MTP MPO fiber optic loopbacks. MTP/APC Singlemode loopbacks, and MTP/UPC Multimode loopbacks using high quality US Conec MTP connectors for the highest quality polish and lowest insertion loss. All fiber modes including 9/125, 50/125, 62.5/125. Our MPO MTP loopbacks in standard configurations such as for QSFP modules for a QSFP MTP loopback tester. Custom MPO MTP loopbacks are also available for any configuration. Call or e-mail us about custom MTP MPO loopbacks- we can make any custom configuration you need for your custom MTP loopback needs.
-
Product
SparkFun GPS Breakout
NEO-M9N, SMA (Qwiic)
-
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options including SMA. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions increasing, precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which makes it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
PCIe-7857, Kintex-7 160T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device
786458-01
Multifunction Reconfigurable I/O
PCIe, Kintex-7 160T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device - The PCIe‑7857 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7857 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
Digital Signage Player With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, DisplayPort++, HDMI, 2 GbE LAN And 4 USB
DSP300-318
-
The DSP300-318 is powered by the onboard Intel® Pentium® processor N4200 and Celeron® processor N3350 (code name: Apollo Lake). It can deliver dazzling visual images and video advertising in 4K resolution. Measuring only 20 mm in thickness, the ultra slim DSP300-318 is sleek enough to fit in a small area behind signage displays and its fanless and cable free design enables easy installation without any environment limitation. The super slim DSP300-318 is designed to be fanless and cableless, which ensures solid reliability and easy maintenance. It supports HDMI and Dual-Mode DisplayPort (DP++) outputs with support for dual displays. The system also has one M.2 Key E 2230 for Wi-Fi and Bluetooth modules, one M.2 Key B 3042 for 4G LTE and one SIM card slots for 3.5G radio connectivity. Additionally, one M.2 Key M 2280 and one optional 64GB eMMC 5.0 are available for storage. The Intel® Apollo Lake-based DSP300-318 offers a cost-effective, compact yet powerful computing platform that allows plenty of digital signage solutions for advertising, brand promotion and digital menu board applications.
-
Product
Kintex UltraScale FPGA Coprocessor - XMC
Model 71800
-
Model 71800 is a member of the Jade family of high-performance XMC modules. The Jade architecture embodies a new streamlined approach to FPGA based boards, simplifying the design to reduce power and cost, while still providing some of the highest performance FPGA resources available today.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-055-HI
-
The 40-230-055-HI (PXI) and 42-230-055-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Extra-low Receiving Transmission Platform
9982, 9984
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai 9982(two outputs) optical receiver adopts advanced GaAs HBT ic technology, and makes the noisy power very low. When the receiving power reaches -6dBm, the system CNR is still above 50dB. 9984 four outputs extra-low receiving optical receiver, its end output port adopts 2 pieces power. Double modules that can supply 4 ways RF output.
-
Product
PXIe Power Relay Module, 3xSP4T, 20 Amp
42-166-201
Relay
The 40/42-166-201 is a PXI/PXIe high density power relay module with 3xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
Digital I/O
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI 4 Slot BRIC 132x8 1-Pole (6 sub-cards)
40-562A-021-132X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Energy Storage/Backup Power
-
Broadband service providers are challenged to reduce their carbon footprints and at the same time expand the reach and performance of their networks to meet escalating subscriber demand. The adoption of an eco-friendly energy storage and backup powering system based on hybrid supercapacitor technology enables service providers to achieve both goals while simultaneously improving network reliability and reducing capital and operational costs. ATX’s Areca™ Energy Storage Solutions include next-generation hybrid supercapacitor modules that offer significant improvements over existing standby power sources, such as valve regulated lead acid (VRLA) and Lithium-based batteries.
-
Product
RF Electronic Calibration Module (ECal), 300 KHz To 18 GHz, 4-ports
N4432D
Electronic Calibration Module
The Keysight N4432D is a precision 4-port ECal module that supports selection of Type-N and 3.5 mm connectors mixed up to 18 GHz. Select either female-female, male-male, or female-male connectors.
-
Product
PXI 16x2 RF Matrix 300MHz 50 SMB With Loop-Thru
40-728-001-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
Modbus Analog Output Modules
DAT3020 Series
-
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-052-HI
-
The 40-230-052-HI (PXI) and 42-230-052-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 5.762MΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784400-02
Voltage Input Module
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It … also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
Product
High Density Interface Card
PMC-A429HD
Interface Card
Alta Data Technologies’ PMC-A429HD interface card offers an unparalled 16, 32 or 48 channels of ARINC-429 on a single-width, front panel PMC module. The PMC card can be used in almost any PCI/PCIe based backplane system, and can encode or decode almost any ARINC-429 physical layer signal. The card can also support several 717 channels.
-
Product
IEEE 1394b/AS5643 Mil1394 (FireWire), Triple-Node Multi-Port, Communications
FW3
-
The FW3 function module provides IEEE 1394b/AS5643 (Mil1394) support on each of its three nodes, which are configured as 2 nodes with 3-ports and 1 node with 2-ports. AS5643 defined flight ready robustness and active transformer isolation to enable longer cable lengths (20 meter) between nodes. Together these standards provide the deterministic and redundant communications protocol required for Vehicle System (Flight Control) Networks. The FW3 multiple ports per node configuration allows the user to create tree, daisy-chain and looped topologies needed to optimize cable length and weight while creating redundancy.
-
Product
PXIe Multi-Channel Function Generator Module, 16-Channel
43-625-003
-
The 41-625-003 (PXI) and 43-625-003 (PXIe) are function generator modules that provide 16 channels in a single PXI/PXIe slot. They can generate sine waves to 300 kHz with 5.76 mHz frequency resolution referenced to the 10 MHz PXI clock. The output voltage range is up to +/-25 V in a 16-bit resolution. It also support PXI trigger functions allowing events from other instruments to initiate waveform generation or sweeps.
-
Product
PXI 8 Slot BRIC 232x6 2A 1-Pole Matrix
40-596-104
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
Isolated USB Digital I/O Modules (OEM Version Available)
USB-7230/7250
Data Acquisition Module
The USB-7230/7250 USB-based digital I/O modules feature high voltage on/off control and monitoring, and isolation voltage supported up to 2500VRMS. The USB-7230 provides 32-CH isolated digital I/O and 2-CH frequency/event counters. The USB-7250 provides 8-CH relay output (4 form C and 4 form A), 8-CH isolated DI, and 2-CH frequency/event counters. The USB-powered USB-7230/7250 features removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
Product
PXIe Measurement Accelerator
M9451A
Measurement Accelerator
The M9451A PXIe Measurement Accelerator combined with Option DPD Digital Pre-Distortion & Envelope Tracking Gateware shows what is possible when you combine state of the art FPGA's with Keysight's trusted measurement expertise and PXIe's high speed data handling. As part of Keysight's RF PA/FEM Characterization & Test, Reference Solution, this combination provides unprecedented performance for demanding envelope tracking and digital pre-distortion measurements required for testing modern power amplifiers (PAs) and front-end modules (FEMs). Hardware acceleration provides better than 20x speed improvement over Keysight's previous host-based Reference Solution, with closed/open loop digital pre-distortion (DPD) and envelope tracking (ET) measurements taking just tens of milliseconds and overall measurement times less than 70 ms.
-
Product
I-87KW High Performance I/O Modules
-
The I-87K High Performance Modules are for use with ViewPAC, WinPAC, XPAC and LinPAC controllers.
-
Product
PXI 8-Slot BRIC Matrix, 60x32 1-Pole (12 sub-cards)
40-562B-121-60X32
Matrix Switch Module
The 40-562B-121-60X32 is a high density BRIC8 matrix module with a size of 60x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Cable Assembly, Receiver, QuadraPaddle & Mini Coax, 36", PCB Adapter
540103010258
Cable Assembly
This cable assembly comes with PCB adapter 510150210 and a Mini Coax module to 4 SMB plugs.
-
Product
Qseven Module With Intel® Pentium® Processor N4200 & Celeron® Processor N3350
Q7M311
-
The Q7M311 has adopted the 14nm Intel® Pentium® N4200 and Celeron® N3350 quad-core/dual-core processors (codename: Apollo Lake). The extremely small embedded module supports 4GB (or optionally up to 8GB) DDR3L memory onboard and 32GB eMMC flash memory (optional). With a seismic design and for industrial-grade temperatures, both the CPU and the DDR3L RAM are soldered to deliver reliable and excellent computing performance. With rich features embedded in all the components built in a small form factor, the industrial-grade computer-on-module is aimed for industrial IoT applications, including industrial control, medical imaging, digital signage, gaming machines, military, and networking.
-
Product
Analog I/O Modules
-
Remote RS-485 I/O modules using Modbus RTU protocol offer complete analog I/O for current, voltage, thermocouple or RTD.
-
Product
PXI 8-Slot BRIC Matrix, 44x8 2-Pole (2 sub-cards)
40-562B-122-44X8
Matrix Switch Module
The 40-562B-122-44X8 is a high density BRIC8 matrix module with a size of 44x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
37-Pin D-Type Female Connector Block
40-965-037-F
Connector Block
Suitable for use on the front of modules this connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
