Modulators
Are devices which varies a characteristic of a repetitious electrical or electromagnetic wave of less than infrared frequency in accordance with a characteristic of an arbitrarily varying information carrying signal.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, SMB
40-837A-002
Matrix Switch Module
The 40-837A-002 (PXI) and 42-837A-002 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-040-HI
-
The 40-230-040-HI (PXI) and 42-230-040-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 102kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 32 x SPDT Reed Relay
40-110-121
Relay
Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
Vector Signal Generator
R&S®SMW200A
Vector Signal Generator
Performance and functionality requirements vary depending on test setup and application. The R&S®SMW200A is unrivaled in mastering this challenge and sets new standards for signal generators. When developing and verifying any type of DUT, including component, module and complete base stations – the R&S®SMW200A always easily generates the appropriate test signals with top performance. The flexible modular design of the R&S®SMW200A can be equipped with the exact options required for specific applications. Any configuration is possible, from a classic single-path vector signal generator to a multichannel MIMO receiver tester.
-
Product
Resistance Meter
MS8-2L
-
M-module MC8-2L is a mezzanine module designed to measure resistance using a two-wire measurement scheme in eight channels (eight-channel digitizer). М-module МС8-2Л is installed on the mezzanine carrier - NM module and is connected to it via a local information highway. Up to four m-modules of various types can be installed on the HM module. The NM module, together with the m-modules installed on it, forms a VXI module of size C-1 and is used to create information measuring VXI systems.
-
Product
PXI 4 Slot BRIC Matrix, 2A 1-Pole 32x12, 1 Sub-card
40-597A-001
Matrix Switch Module
The 40-597A-001 is a PXI 1-pole 32x12 matrix in BRIC4 format and is part of a range of high density matrix modules able to switch up to 2 A or 200 VDC/210 VAC. The 40-597A BRIC modules are available in 2, 4 or 8-slot sizes to suit most high performance PXI matrix requirements, constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 16 Bank 5 Channel 1 Pole Multiplexer
40-616-021-16/5/1
Multiplexer Module
The 40-616 16-Bank, 5-Channel, 1-Pole Multiplexer Module forms part of the System 40 PXI Programmable Switching system. The Module consists of 16 electrically isolated banks of multiplexers controlled by a PXI/ PCI interface. Each bank is a 1 to 5 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously. The module is suitable for cascading in applications that require large multiplexer systems, it is also suitable for test systems that require the switching of a large number of signals in parallel.
-
Product
104 Pin D-Type Cables - Connector to Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 104-pin D-type connector.
-
Product
Variable Optical Attenuator Module with Angled Interface
81571A
Optical Attenuator
The Keysight 81571A variable optical attenuator features lowest insertion loss and excellent wavelength flatness over a complete attenuation range of 60 dB, for characterizing optical network components for telecommunication and data communication in systems.
-
Product
PXI 8-Slot BRIC Matrix, 88x4 1-Pole (2 sub-cards)
40-562B-121-88X4
Matrix Switch Module
The 40-562B-121-88X4 is a high density BRIC8 matrix module with a size of 88x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
500 Pin SEARAY Cables - Connector to Unterminated For Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a 500-pin SEARAY (250-port) connector.
-
Product
PXI Dual SP6T Multiplexer 40GHz 50 SMA-2.9
40-784A-042
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 40 GHz, 50 Ω, SMA-2.9, Failsafe
42-780B-543
Relay
The 40-780B-543 (PXI) and 42-780B-543 (PXIe) are triple failsafe SPDT 40 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
Industrial PC/104-Plus AMD LX800 x86 Single Board Computer
PPM-LX800-G
-
The PPM-LX800-G is a highly integrated, industrial PC/104-Plus single board computer (SBC) designed for embedded, space-limited, low power applications. It is a full-featured SBC that includes an AMD LX800 x86-compatible CPU, CRT and flat panel video controller, 10/100 Ethernet, two USB 2.0, 16 lines of digital I/O, and four COM channels on a single 3.6 x 3.8 inches (90 x 96mm) module.
-
Product
(100×130×19mm) C-Band DWDM Booster EDFA Module
WBA4100-FM04
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WBA4100-FM04 series used 100 x 130 x 19mm compact package, is a digital control circuit of DWDM power amplifier function module. Products using the most excellent optical properties, electronic control technology and complete software function is most advanced, wide wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Application for C-Band 44 wave or the 88 wave of DWDM system.
-
Product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
Digital I/O
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
3-Port ROADM / TOADM
-
Optoplex's Reconfigurable Optical Add/Drop Multiplexer (ROADM) module, also known as Tunable Optical Add/Drop Multiplexer (TOADM), is based on a proprietary micro-optics and micro-actuator design, athermal packaging technology, and state-of-the-art thin-film coating. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), this 3-port ROADM device directs a selected channel to the Drop-Port (ADD/DROP) and the remaining channels to the Express-Port (EXP), as depicted in the figure below. This tunable feature can also be used for adding a channel, when the device is used in reverse. Cascading two ROADM modules, simultaneous add and drop functions can be achieved. Each single ROADM device is optimized to cover either C- or L-band wavelengths. The standard 100- or 200-GHz channel spacing ROADM products allow for single-channel drop. Customized banded-channel drop ROADMs are available upon request.
-
Product
Freescale QorIQ T4241 Or T4161 Processor, PCIe, 3U VPX
VPX703
-
The VPX703 is a Processor VPX (PrVPX) in 3U form factor based on the Freescale QorIQ T4241 or T4161 in a single-module. The PrVPX has 64 GB of onboard flash for storage. The module routes standard I/O such as SATA, USB, GPIO, RS232, etc. to the P1 connector.
-
Product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
-
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
Product
Globe Temperature Probe
TP3276.2
-
Globe temperature probe with Pt100 sensor, globe Ø 50 mm. Stem Ø 8 mm, length 170 mm. Complete with SICRAM module.
-
-
Product
Modular Functional Test Platform
LX-OTP2
Test Platform
The OTP² system platform has recently been available in both the PXI and LXI versions. The OTP2 system platform enables the cost-effective and fast implementation of function test systems based on defined modules and function blocks. Thanks to the open system interfaces, customer-specific adjustments can be made at any time without any problems. When considering options for your next generation functional test system, it is important to assess the entire life cycle of the system and the associated costs and efforts. Use OTP² to accelerate development cycles and reduce the development effort for new functional test systems.
-
Product
External Load Module
ELM
-
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
Product
FPGA PXI Card With 80 Channel LVDS Buffer Module
GX3611
FPGA PXI Card
The GX3611 is a 3U PXI FPGA card with 80, LVDS channels and is comprised of the GX3500 PXI FPGA card and the GX3511 expansion card.
-
Product
RF PXI Matrix Modules
-
Pickering's RF PXI Matrix Modules are capable of providing economic switching for frequencies up to 6 GHz. Our other RF PXI options include RF SPDT switches and RF multiplexers, for higher frequency applications or applications requiring high-performance levels, please take a look at our microwave switching modules.
-
Product
PXI 8 Slot BRIC 506x8 1-Pole Dual Analog Bus (11 sub-cards)
40-560A-121-506X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Base Model Custom-Configured DC Power Analyzer, 600 W, Modular, 4 Slots
N6715C
DC Power Analyzer
The N6715C DC Power Analyzer is a build-to-order system that is shipped as a fully tested and assembled DC Power Analyzer. Each N6715C consists of one N6705C mainframe (described below) plus 1 to 4 DC Power Modules and up to 600 W total DC Power Module output power. To specify which modules you want installed in the N6715C, modules are ordered as options to the N6715C.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-156-HI
-
The 40-230-156-HI (PXI) and 42-230-156-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 76.8MΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 28x16 Matrix Module, 1-pole 2A 60W
40-579-001
Matrix Switch Module
The 40-575/576/577/578/579 are a range of high density matrix modules able to switch up to 2 Amps or 300VDC/250VAC. They are constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 4 Slot BRIC 88x8 2A 1-Pole Matrix
40-567-002
Matrix Switch Module
The 40-567 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-567 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
