DC Hipot
See Also: Hipot Testers, Hipot
-
product
Adapter, 2.4 mm (m) to 2.4 mm (m), DC to 50 GHz
11900A
The Keysight 11900A is a metrology-grade, 2.4 mm male to 2.4 mm male adapter with dc to 50 GHz operation.
-
product
DC Parametric Test System with Curve Trace
DC3
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
product
MTM-PM-1: 1-Channel DC Power Module
EXCELS AT POWER: The MTM-PM11 1: Channel DC Power Module excels at powering devices that need stable power under large transient loads during manufacturing and R&D testing. Optimized for devices using LiPo or similar batteries. Accurate voltage, temperature and current measurements can be made through the powerful and cross-platform BrainStem API.
-
product
Coaxial Termination, DC to 50 GHz
85138B
The Keysight 85138B is a precision, low-reflection dc to 50 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 85138B has a 2.4 mm female connector.
-
product
AC + DC TRUE RMS Digital Multimeter With PC Interface
KM 829
Kusam Electrical Industries Limited
• Beep-Jack Audible & Visible Input Warning• Auto-Ranging• Relative Zero Mode• PC Interface Capability• AutoCheck V-Ω ; Auto-Ranging• Crest (Instantaneous Peak Hold)• T1-T2 differential Temperature readings.• Data Hold
-
product
DC Josephson Voltage Standard
The system enables a number of calibration and measurement functions for dc voltages:*Calibration of secondary standards*Calibration of linearities and accuracies of dc voltmeters in the measuring range from 0 to ± 10 V.*Extremely exact output of any reference voltages*Direct comparison of two voltage standard measuring systemsNo other measuring system in the world offers such a variety with the highest precision.
-
product
AC VOLTAGE MEASUREMENT (AC or AC + DC TrueRMS) Digital Multimeter
1320
± 199.9mV, ± 1.999V, ± 19.99V, ± 199.9V, ± 1200V, 5 Ranges, AC VOLTAGE MEASUREMENT (AC or AC + DC TrueRMS)
-
product
DC Clamp Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Is used to measure the DC currents.
-
product
Cal Kit, 4-in-1 OSLT, DC To 26.5 GHz, 3.5 Mm(f)
85521A
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
product
DC Bias Current Source
FD1772B
• Constant DC output 0-6A• Auto or manual current sweep output• 5 current range output• Output voltage range: 0-11.5V• Current accuracy ± (1%reading + 2digit)
-
product
DC Coreless Motor
Adamant Namiki Precision Jewel Co Ltd.
There is a structure in the cage shape by only the copper wire turns around a cylindrical permanent magnet placed inside It is a feature. There There is not an anron core, it does not receive the action of the copper basket type rotor is light, the moment of inertia becomes small, so quick response is possible. A Permanent Magnet, There Is No Cogging, That Is, Rotation Is Smooth, And Vibration And Noise Can Be Reduced. - Since Rare Earth Magnets With High Magnetic Properties Are Used And The Rotor Is Formed Only With Coils, The Motor Itself Can Be Made smaller and lighter.
-
product
DC Power Supply
CSP-3
● Universal power AC90~264V/DC127~380V● Build in power factor control circuit in high power model(120W~500W)● Available for series and parallel operation● To be a Back up power function with relay output in option( not available in model 20W and 24W)● RoHS & UL version in option● DIN rail mounting
-
product
DC Power Module, 20V, 5A, 100W
N6743B
The Keysight N6743B is a 100 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
product
DC Blocking Power Splitter Combiner
PD5160
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type SMA Female (Jack) 50 Ohm
-
-
product
High Performance Autoranging DC Power Module, 50V, 5A, 50W
N6751A
The Keysight N6751A is a 50 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
product
Clamp Meter, Auto, Average, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-9480
Tenma 72-9480 Digital Clamp Multimeter
-
product
Coaxial Switch, DC to 26.5 GHz, SPDT
8762C
The Keysight 8762C offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.
-
product
3 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 3 Ports
GPS312
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
product
Programmable DC Power Supply
IT6100B Series
IT6100B series (86 ~ 1200W) high speed high precision programmable DC power supply is withultra high voltage rising time, the fastestfull load up to 500us, resolution up to 0.1mV / 0.01mA, the latest output waveform priority mode allows rising waveform ofvoltage or current is with high-speed and no overshoot, which is widely used inaerospace power modules and other high-precision test occasions. IT6100B hasbuilt-in standard USB / RS232 / GPIB communication interface and the panel supports List programming, which canprovide multi-purpose solutionaccording to customer design and testing demands, easy to use.
-
product
Benchtop DC Electronic Load
63000
Chroma Systems Solutions, Inc.
The 63000 series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power supplies, A/D power supplies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices.
-
product
DC Power Supplies
DLM 3-4 kW
AMETEK Programmable Power, Inc.
The Sorensen DLM 3kW and 4kW Series programmable DC power supplies are designed to provide highly stable, continuously variable output voltage and current for a broad range of applications in a compact 2U ( 3½” high) chassis.
-
product
Resolver to DC Sine / Cosine or Synchro to DC
ST-RD & ST-SD
Computer Conversions Corporation
ST-RD and ST-SD Series - Resolver to DC Sine / Cosine or Synchro to DC Sine Cosine Packaged on PCB with Track and Terminal Block and On-Board AC Reference Supply may be used driving DC Servo amp in active position synchronizing applications
-
product
1.0 mm Female to Circuit Card Launch, DC to 110 GHz
11923A
The Keysight 11923A 1.0 mm female connector launch is designed to thread into a package or fixture housing to transition a microwave circuit from microstrip to coaxial connector. The Keysight 11923A connector launch is intended for use with 110 GHz test systems such as the Keysight 8510XF. The Keysight 11923A comes pre-assembled, but the user is responsible for machining the package and installing the connector. The procedure describing the necessary geometry for the package and installation will be provided.
-
product
DC Electronic Load
3310G Series（75W~400W）
Each 3310G Series module has its own control and display panel, CC / CR / CV / CP / Dynamic modes, plug in 3302G / 3305G / 3300G mainframe with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
product
Precision Source / Measure Unit, 1-Channel, 10 FA Resolution, 210 V, 3 A DC / 10.5 A Pulse
B2911B
The Keysight B2911B precision source / measure unit (SMU) is a 1-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current. It easily measures current versus voltage (I/V) with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
product
DC High-Voltage Test Device
PGK 25
BAUR Prüf- und Messtechnik GmbH
Cable testing with the BAUR PGK 25. Cables must be tested in compliance with the national and international standards. This applies before the commissioning of new cable networks. The portable BAUR PGK 25 cable test device is used for DC voltage testing in low- and medium-voltage cables. It is characterised by its low weight of only 16.5 kg, by the easy operation and solid construction for onsite use.* Compact device for DC voltage testing with negative polarity* Continuously adjustable output voltage* Perfect for mobile use
-
product
DC SQUID System
Quantum Design's patented high-symmetry SQUID design and electronics provide the most rugged and sensitive all-thin-film sensors commercially available, and give you everything you need to configure flexible, powerful detection systems for your research. These sensors can easily withstand the rigors of a laboratory environment such as repeated temperature cycling. Their robust performance offers a level of reliability and adaptability that has earned QD a worldwide reputation as the SQUID of choice. OEM services are also available for special commercial applications.
-
product
PXI Multiplexer, Very High Power DC, 4-Channel, 20A, 28V
40-664A-002
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
