Analog Oscilloscopes
Analog oscilloscopes directly apply a voltage being measured to an electron beam moving across the oscilloscope screen, which deflects the beam up and down, tracing the waveform on the screen. (fluffah.phy.uncwil.edu)
See Also: Oscilloscopes, Digital Storage Oscilloscopes, Oscilloscope Probes
-
product
WiFiScope WS6: 500 MS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-500XM-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
product
Oscilloscope, 100 MHz, 4 Channels
DSOX3014A
100 MHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
product
PXI Oscilloscopes & Digitizers
Keysight's wideband digitizers can run at 3.2 GS/s, with up to2 GHz instantaneous analog bandwidth. They feature a Xilinx Virtex-6 FPGA that can implement different functionalities depending on which firmware option is selected.
-
product
MDS Audio Oscilloscope / Spectrum Analyser
Sampling frequency: 8 000 - 192 000 HzVertical resolution: 16 bitSound card selection: YESChannels count: 2Channels modes: independent, I master - II slave, II master - I slaveMath: Ch1=Ch1+Ch2; Ch1=Ch1-Ch2; Ch2=Ch2+Ch1; Ch2=Ch2-Ch1Signal reconstruction: YESPretrigger: YESTrigger events: above, below, free runInternal trigger: YESExternal trigger: two channel mode - NO, single channel mode - YESData visualisation modes: single, continuous displayFFT points count: 8 - 2 097 152FFT Window functions: Rectangular, Gauss, Hamming, Hann, Bartlett, Triangular, Bartlett-Hann, Blackman, Nutall, Blackman-Harris, Blackman-Nutall, Flat TopOscilloscope amplitude axis units of measurement: Volts (nV...kV), Sample Value (smp)
-
product
60 MHz USB Oscilloscope
522
The Dataman 522 is a dual channel oscilloscope with 60 MHz bandwidth and USB 2.0 connectivity • USB powered - no additional power supply is required • Dual channel with external trigger • 60 MHz bandwidth • 50 MS/s real time sampling rate • 5 GS/s equivalent sampling rate • 8,000 sample buffer per channel • Hi-speed USB 2.0 connectivity allowing fast and easy connection to PC’s and laptops • Comprehensive 2 years parts and labor warranty • Free life-time software updates
-
product
Plus Super Phosphor Oscilloscopes
SDS2000X
The SDS2000X Plus series employs SIGLENT’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications which require more than 8-bit resolution.
-
product
16-Bit D/A Analog Output
PMC230A
PMC230A modules have eight 16-bit D/A converter (DACs) to provide highly-accurate analog voltage outputs. A unique two-piece board design brings the proven reliability of Acromag’s IndustryPack® (IP) A/D modules to a PMC format. An IP230A module is embedded on a PMC interface card that maintains maximum performance and transparent communication to the host.
-
product
MXG X-Series Microwave Analog Signal Generator, 9 kHz to 40 GHz
N5183B
Get a fast, compact (2U) alternative to the PSG in the lab, depot or fieldAddress demanding tests of radar modules & systems with near-PSG levels of spectral purityCompensate for system loss & drive high-power amplifiers: +19 dBm output power, -55 dBc harmonics & -68 dBc spurious @ 20 GHzReduce calibration time with switching speed 600 sSimulate narrowband chirps & radar antenna scans with up to five internal function generators that can be used with AM, FM, OM pulse modulation
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3016-16
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
-
product
Analog Power Modules
Renesas' family of analog power modules offers users a fully integrated DC/DC switching buck converter in one package. These modules combine the controller, power FETs, output inductor, and compensation circuitry in a single package minimizing both the external component count and complexity of converter design.
-
product
PCI 12-Bit Analog Output Cards
PCI-DA12-2/4/6 & PCI-DA12-8/16
PCI-DA12-8 and PCI-DA12-16 are full-size cards that can be installed in long slots of PCI-Bus computers. They contain eight and sixteen independent double-buffered, digital-to-analog converters (DACs), and three 16-bit counter/timers.
-
product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
16-bit D/A Analog Output
IP236A-8
IP236A-8 modules have 16-bit D/A converters (DAC) to provide highly-accurate analog voltage outputs. FIFO buffers enhance control over the transfer of data to the DAC and improve efficiency.
-
product
Dual-channel Digital Oscilloscope
ScopeDAQ 12
Dual-channel digital oscilloscope ScopeDAQ 12 allows the user to capture the data with frequency 50MHz. Higher sampling frequency (100MHz) is available in case of using one channel. Basic version of the instrument is equipped with 128K data buffer, optionally it can be enlarged up to 512KB.
-
product
HandyScope HS6-DIFF: 200 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-200XM-W5
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
product
PXI 8 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-121-184X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Analog Output Expansion Board
MSXB 032
The MSXB 032 Analog Output Expansion Board converts digital inputs from a Data Acquisition Processor into four separate analog outputs. Up to 16 Analog Output Expansion Boards can be connected to a Data Acquisition Processor for a maximum expansion of 64 analog output channels. The MSXB 032 is compatible with Microstar Laboratories Industrial Enclosures.
-
product
Analog & Analog Pwr.
*2 inputs 0-10V or 4-20mA*Possibility of triggering the measurement via 2 dedicated inputs*Local and remote configuration*Consumption controlled for optimized autonomy*Develop new preventive maintenance services, alerts and analyzes.
-
product
CC15010X, 10 MHz, 150 A Current Oscilloscope Probe
786849-01
The CC15010X, or Hioki 3274, is a clamp-on current probe that offers a wide DC to 10 MHz bandwidth and 150 A of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor controllers. The probe requires an external power supply.
-
product
PC-based DSP Systems with Analog I/O
PCI, cPCI / PXI : 32 / 64 bit, 33MHz6711 or 6713 DSP32MB SDRAMLow latency burst interfacesHigh data transfer ratesGreat trigger flexibilityMultiboard support
-
product
T3DSO1000/1000A Series Oscilloscopes
T3DSO1000/1000A Series
Teledyne Test Tools new T3DSO1000/1000A Oscilloscopes feature two channel and four channel models. The two channel model is available in 100 MHz, 200 MHz or 350 MHz bandwidths, a single ADC with up to 2 GSa/s maximum sample rate, and up to 28 Mpts of sample memory. The four channel scope is available in 100 and 200 MHz models and incorporates two 1 GSa/s ADCs and two 14 Mpts memory modules. When all channels are enabled, each channel has sample rate of 500 MSa/s and a standard record length of 7 Mpts. When only a single channel per ADC is active, the maximum sample rate is 1 GSa/s and the maximum record length is 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
product
RF Analog Signal Generators
The right solution for your requirements from the broad analog signal generator portfolio of Rohde & Schwarz.With the analog signal generator portfolio we cover the wide range of RF, microwave and mmWave frequencies.Our selection of analog signal generators is characterized by the outstanding signal purity and performance as well as their functionality of the solutions; whether in the high end or midrange area.The solutions benefit industries such as RF semiconductor, wireless communications, aerospace and defense, and also covers tasks featuring development, production and service, and more.
-
product
16 SE Or 8 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-16-4C
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
DSO Shell Oscilloscope DIY Kit
DSO150
DSO Shell has similar bandwidth as DSO138 but contains significant improvements in structure, mechanical, and operation.
-
product
Digital Oscilloscope
MSO5000-E Series
Mso5000-e series digital oscilloscope is based on the technology of RIGOL ultravision II, which is a high-performance and economical digital oscilloscope specially designed for professional engineers.
-
product
High Definition Oscilloscope, 500 MHz Bandwidth, 4+16 Input Channels, 10 GS/s
HDO4054A-MS
500 MHz,4+16Ch,12-bit,10 GS/s,12.5 Mpts/Ch HD Mixed-Signal Oscilloscope w/ 12.1" WXGA Color Display.
-
product
Portable Analog Instruments
Instrument transformer is a general term for voltage transformers and current transformers that are used with electrical instruments. The main purpose of instrument transformers is to extend the measurement range for electrical quantities (voltage, current, power, power factor) on large-current and high-voltage circuits. They serve to convert currents and voltages to levels that are suitable for measurement, and to insulate the instrument, etc. from high-voltage circuitry.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
16-bit, 200KHz, 8SE/4DIFF Isolated Analog Input Board
APCI-3016-8
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
