Tuners
Adjusts a signals frequency to one frequency or band of frequencies.
-
Product
Manual Tuners
-
Manual tuners are used both in the laboratory and as system components to establish or transform impedances for a number of applications. They can be used to establish optimum source or load terminations for device characterization, normalize a source or load for precision laboratory measurements and/or calibrations (noise, power, etc.), and can act as a matching transformer between a mismatched source and a mismatched load.
-
Product
Automated Tuners / Impedance Tuners / Load Pull Tuners
-
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
Product
Palstar Tuners
-
alstar tuners, speakers, and accessories are for amateur radio operators who demand the highest quality of contemporary engineering designed for Ham Radio.
-
Product
Analog Receiver / RF Tuners
-
The Bandit™ family of analog receivers or RF tuners provide a series of high-performance, stand-alone RF downconverter modules. These products offer a low noise figure, programmable gain and a high dynamic range and ensure there are no gaps in the RF spectrum coverage.
-
Product
Demodulators and Tuners
-
ST offers standalone demodulation ICs for cable, satellite or digital terrestrial data transmission. Demodulation is also is integrated in many of our multimedia and application processor SoCs.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - PCIe
Model 78791
-
Model 78791 is a member of the Onyx® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. It is suitable for connection directly to an L-band signal for SATCOM and communications systems.
-
Product
MFJ Dummy Load/Wattmeter
MFJ-267
-
1.5 kW Dry Dummy Load has built-in precision, true peak-reading SWR/Wattmeter switchable to external antenna! Worlds most versatile 1.5 kW dummy load has a built-in true peak reading SWR/Wattmeter that you can switch and use independently! Youll find tons of uses! Tune up your transceiver, linear amplifier, or antenna tuner into a safe 50 Ohm dummy load at full power.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 57791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- One programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconvertersXilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Multichannel COMINT Receiver
HUGIN 2000
-
HUGIN 2000 Multichannel Receiver is the flagship of Novator Solutions COMINT receivers. The COMINT receiver utilizes one or two high-end wideband RF tuners and enable the users to monitor wideband spectrums and receive thousands narrowband channels.
-
Product
L-Band RF Tuner and 4-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 58690
-
- Two L-Band tuners accept RF signals from 925 MHz to 2175 MHz- Two programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- Two programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Four 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Automatic Antenna Tuner 3.5 kW
DU 3500 AL
-
The DU 3500 AL automatic tuner has been primarily manufactured for an automatic PA, but it can also be used with any manual PAs as well. The tuner is primarily compatible with the OM POWER automatic PA.This tuner was designed for antennas calibrated to HAM BANDs. The maximum power can only be utilized with these antennas. With other antennas, it should be set at a lower power (max. 2kW).The major advantage of the tuner is that during competitions it is possible to change BANDs particularly quickly.
-
Product
Antenna Tuner
DU-3000T/DU-3000TB
-
The DU 3000T and DU3000TB tuners optimize the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU-3000 series also measure the Power and Standing Wave Ratio (SWR), which allows you to tune the indicated SWR to the lowest possible value for the selected transmitfrequency.
-
Product
Modulator
SFT3348C
-
Hangzhou Softel Optic Co., Ltd.
SFT3348C is a high performance and cost-effective DVB-C modulator designed by Softel. It has 8 DVB-S2 tuner inputs, after multiplexing, scrambling and modulating process, then it gives 4 RF output. To meet customers’ various requirements, this device is also equipped with 128 IP input and 4 MPTS output over UDP and RTP. Its pluggable structure design greatly facilitates the change of modules as needed. Moreover, the four CAMs/CIs accompanied can descramble the programs input from 8 Tuner inputs. SFT3348C can be upgraded and controlled through network system, which allows it to be widely used in setting up digital broadcasting network and very adaptable to newly generation CATV broadcasting system.
-
Product
1100-Channel GSM Channelizer wih Quad A/D - PCIe
Model 78663
-
Model 78663 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This fourchannel, high-speed A/D converter with1100 GSM DDCs (digital downconverters) accepts IF signals from an RF tuner. It is ideal for capturing all transmit and receive signals in both upper and lower GSM bands.
-
Product
Autotuner
HF-AUTO-R
-
The Palstar HF-AUTO-R is the full-function remote control unit for use with the HF-AUTO automatic antenna tuner. The HF-AUTO-R allows for remote operation of the HF-AUTO base unit up to 500' away and duplicates all buttons, controls, and display info.
-
Product
Antenna Tuner
DU-1500L
-
Model DU 1500 L is high power antenna tuner that uses and adjustable reactive network for matching the unbalanced 50 ohm output impedance of transmitters and transceivers to a variety of balanced and unbalanced loads.It is usable over a frequency range of 1.8-30 MHz. Provision is made for selecting one of three antennas or for bypassing the matching network.A crossed needles SWR and wattmeter with switchable 200 and 2000 watt scales and selectable peak and average power output reading is included.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - XMC
Model 71791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O
-
Product
Camera Detector
P7030
-
The easy to use Camera Detector is so small it can be carried or stored anywhere. Discreet sweeps of the home, office or hotel room can be done quickly and efficiently. When a camera is discovered, a LED light flickers and an audible alarm sounds. An auto adjusting sensitivity tuner allows you to scan variable distances and can check multiple channels. It can detect frequencies anywhere from 50 MHz to 3 GHz, picking up most wireless cameras.
-
Product
RF Switch Modules
-
Analog Devices RF switch modules include the highest bandwidth switch modules. SPST, SPDT, SP4T, SP6T, and SP8T versions (reflective and absorptive) are available for a wide range of power (up to 27 dBm) applications, including antenna switching, filter switching, and tuner applications.
-
Product
Single-Axle Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/1 CAR | VP 230035
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/1 single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/1 CAR guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
-
Product
Antenna Tuners
DU-3000T / DU-3000TB
-
The DU 3000T and DU3000TB tuners optimize the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 3000 series also measure the Power and Standing Wave Ratio (SWR), which allows you to tune the indicated SWR to the lowest possible value for the selected transmitfrequency.
-
Product
Slide Screw Tuners
-
Slide screw tuners are particularly suited to establishing impedances for device characterization, or for any other application requiring a precisely repeatable mismatch condition. This is due to the precision with which a specific matching condition can be repeated if the tuner has calibrated position indicators.
-
Product
Automatic Antenna Tuner
-
Automatic Antenna Tuner has not been released for full Beta testing and production yet as we are solving some firmware issues. We cannot give you a date nor estimate at this time when full production will commence.
-
Product
Frequency Multipliers
Triplers
-
*No mechanical tuners*fullband operation*planar design*zero Bias
-
Product
Autotuners
HF-AUTO
-
The Palstar HF-AUTO 1800 watt automatic antenna tuner covers 160 to 6 Meters with a power rating of up to 1800 watts PEP. Hams have enjoyed the benefits of low power auto-tuners for years, but now Palstar takes it to the next level and offers auto-tuning with a power rating of 5 Watts to 1800 watts.
-
Product
Mechanical Noise Tuner Control
S93027B
-
The S93027B enables to control Maury Microwave’s LXI tuner as the impedance tuner and measure the noise figure of unmatched devices (Gamma opt. < 0.9) with the N524xB PNA-X with option 029 and the S93029B noise figure measurement software.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 57690
-
- One L-Band tuners accept RF signals from 925 MHz to 2175 MHz- One programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- One programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Dual L-Band RF Tuner and 4-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 58791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Two programmable LNAs handle L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Four FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI-2556, 2.5 GHz, 75 Ω, Dual 4x1 PXI RF Multiplexer Switch Module
778572-56
Multiplexer Module
2.5 GHz, 75 Ω, Dual 4x1 PXI RF Multiplexer Switch Module—The PXI‑2556 is an RF signal multiplexer switch module. The multi-bank architecture of the NI PXI‑2556 makes it ideal for test systems that require parallel operations such as the stimulus/response testing of video RF devices such as tuners. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
