Test Receivers
Devices whose purpose is to capture transmitted signal energy and record specified characteristics. These recordings are then examined to ensure that the sending device is working according to specifications. (www.techfest.com)
-
product
PCI Express 6 Base Specification Receiver Test Automation
N5991PB6A
The N5991PB6A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 6.0 ASICs
-
product
PXE EMI Test Receiver, 1 Hz to 44 GHz
N9048B
Keysight's N9048B PXE is a standards-compliant EMI test receiver equipped with an RF pre-selector and LNA designs. Shorten your overall test time and easily perform gapless signal capture and analysis with real-time scan (RTS) capabilities.
-
product
RF Capture & Player
This device can record RF signals in various points of fields. When reproducing the signal data infactories or laboratories, it is possible to test receivers under the reception environment of the data.
-
product
Optical Receiver Stress Test Solution
N4917BSCB
The Keysight N4917BSCB optical receiver test solution is a complete, automated and repeatable solution for optical receiver stress test.
-
product
Test Receiver
NTR GNSS
Our primary objective is to provide a high performance and fully flexible test receiver for all types of GNSS systems. Thus, the NTR fully supports all existing navigation systems. The signal processing is fully flexible. The high performance correlation engine with up to 80 channels is implemented in a powerful set of FPGAs. Signal acquisition and tracking are realized on a high performance embedded ARM Cortex A8.Supporting up to 4 L-band frequencies in parallel, the NTR GNSS test receiver supports all current GNSS transmission frequencies. Due to its plug-in design, the RF front-end can easily be customized for special filtering and other frequencies.
-
product
Bit Error Ratio Testers
Keysight’s bit error ratio test (BERT) system enables the most accurate physical-layer design verification of high-speed communication and multi-gigabit digital interfaces. Our expert-level support will help you select the high-performance hardware, control software, receiver test, and automation tools needed to help you master your design.
-
product
Radio Test Set
CMA180
With its frequency range from 100 kHz to 3 GHz, the R&S®CMA180 is ideal for testing all common analog and digital radio systems. Input levels up to 150 W are no problem for the R&S®CMA180. The flexible internal switching capabilities for the audio and RF paths make the R&S®CMA180 suitable for a wide range of test requirements. Users can configure the internal generators, external audio sources, filters and measurements according to the given application. In the predefined test scenarios for receiver, transmitter and duplex tests, the RF and audio paths are preconfigured. This saves time and eliminates configuration errors for standard test cases.
-
product
EMI Test Receiver
ESL
The R&S®ESL EMI test receiver combines two instruments in one, measuring EMC disturbances in accordance with the relevant standards and also serving as a full-featured spectrum analyzer for diverse lab applications. The combination of very good RF characteristics and all of the important functions needed for fast, precise measurement and evaluation of the EMC of a device under test in accordance with commercial standards is unmatched in this instrument class.
-
product
Saluki LSG022 Analog Signal Generator (Modular)
Saluki LSG022 analog signal generator offers 100kHz to 22GHz frequency coverage with 10ms frequency switching speed. It can be used independently or combined with the chassis to form a test system.Saluki LSG series signal source is the cost-effective choice when you need to balance budget and performance. It provides the signals you will need for radar performance evaluation, high-performance receiver test and components parameter test etc..
-
product
Radar Simulation Software
Pulse Sequencer
R&S®Pulse Sequencer software together with a vector signal generator from Rohde & Schwarz or just as software provides a compelling radar signal generation solution to engineers and technicians responsible for testing radar receivers. The solution is in line with the trend of testing more in the lab rather than expensive field testing. Co-engineered with the industry, the solution supports all relevant modern radar scenario test cases and can account for real-world environments. It uses commercially available R&S®Pulse Sequencer PC software and off-the-shelf Rohde & Schwarz vector signal generators.
-
product
1.6T Optical Receiver Test Application
N4917DJCA
Offers fully automated stress eye calibration and receiver testing for 800G and 1.6T modules with 100G and 200G / λ optical interfaces.
-
product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
product
DisplayPort 2.0 Receiver Test
N5991DP2A
Use the Keysight N5991DP2A DisplayPort 2.0 Receiver Test Software to test, debug and characterize your DisplayPort Sink products maximizing the usage of your test instruments.
-
product
Test Analysis for Land Seismic Systems
Testif-i Land
Testif-i Land is an independent, powerful and cost effective software suite that allows you independently process instruments, source and receiver tests to confirm that the equipment is performing correctly and within specification. The software includes modules to perform comprehensive analysis of vibrator wireline similarity test data. Analysis includes a harmonic intensity plot which can highlight problems such as sub-harmonics which may not be seen on numerical results. Geophone pulse tests can be analysed using the receiver response module and test data from third party geophone testers can be graphed and statistics produced for ease of interpretation.
-
product
Step-Tunable Laser Source, High Power and Low SSE, Basic Line
N7779C
The new N7779C basic line step-tunable laser source is ideal for cost-effective testing of broadband optical devices. It can also serve as a highly stable, tunable local oscillator for receiver testing or transmission experiments.
-
product
RMC
Receive Multicoupler (Rx AIT)
*Provides a common receive distribution point for multiple basestations*Each Cellular and PCS unit supplies 8 ports and supports 2 channels*The single 1U tray includes integrated Bias- T and test ports*QMA receive connectors provide quick and sure connections
-
product
Digital Wideband Transceiver Analysis
S94610B
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver types by defining device operation settings, transmit/receive switching, reading and writing digital IQ waveform from and to DUTs. Acquired RF or digital data is processed in the VNA’s applications for faster, accurate measurements and analysis.
-
product
PCI Express 4 U.2 Receiver Test Automation
N5991PU4A
The N5991PU4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express U.2 devices and hosts at 8 GT/s.
-
product
Modernized Navstar Security Algorithm (MNSA) M-code Testing
SimMNSA
The M-code signal is part of the security architecture that all new Military GPS User Equipment (MGUE) has been required to use since 2017. Until recently, testing with non-classified AES-encryption and replay of M-code Satellite Data Sets (SDS) have been the only methods authorized for GPS M-code receiver testing using a constellation simulator.
-
product
EMC Test Receiver w/ Real-time bandwidth to 685 MHz
TDEMI ULTRA
TDEMI ULTRA offers real-time bandwidth up to 685 MHz, ultra-fast receiver scanning and real-time scanning up to 40 GHz. Offers highest performance for all challenging applications. Also a time-saving and highly efficient full automation of your EMC and communication testings according to all EMC or ETSI standards is available by the EMI64k software suite.
-
product
Modbus Simulator
Modbus Slave
Modbus Slave is for simulating up to 32 slave devices in 32 windows!. Speed up your PLC programming with this simulating tools. Start programming and test before you receive your slave device from supplier.
-
product
PSG Vector Signal Generator, 100 kHz to 44 GHz
E8267D
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
product
PCI Express 5 CEM Receiver Test Automation
N5991PC5A
The N5991PC5A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 5.0 CEM Add-In Cards and systems.
-
product
Spectrum Analysis, Up To 70 GHz
S930907B
The S930907B spectrum analysis (SA) adds high-performance microwave spectrum analysis to the N522xB/N524xB PNA family up to 70 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/cd
M8091BSCB
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
product
Capture & Replay Of I/Q Data Files
SimIQ
Generate RF from I/Q files & accelerate product development. SimIQ enables Spirent’s GSS9000 and GSS7000 Series simulators to capture, replay and share I/Q data files without the need for additional hardware. This capability opens up opportunities for testing receiver algorithms earlier in the development cycle, saving time and money while delivering greater collaborative processes to global teams through simple sharing and consistent playback.
-
product
Spectrum Analysis For E5081A Up To 20 GHz
S960904B
The Keysight S960904 spectrum analyzer (SA) software application adds high-performance spectrum analysis to the E5081A ENA-X up to 20 GHz. With fast-stepped FFT sweeps resulting from optimized data processing, the SA software application provides quick spurious searches over broad frequency ranges. The application enables simultaneous spectrum measurements using test and reference receivers. The multichannel SA pairs with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application uses source-power and receiver-response calibration and fixture de-embedding, providing highly accurate in-fixture and on-wafer spectrum measurements.
-
product
PCI Express 5 Base Specification Receiver Test Automation
N5991PB5A
The N5991PB5A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 5.0 ASICs
-
product
Electrical Receiver Conformance Test Application for OIF-CEI 4.0
M809256CB
OIF-CEI 4.0 receiver test application for OIF-CEI 56G very short reach, medium reach, and long reach PAM4.
-
product
Receiver Conformance Test Application for OIF CEI 5.0
M809212CA
OIF Receiver Test Application for CEI-112G-VSR,-MR and -LR PAM4 interfaces.
