Relay Drivers
Control the energized state of relays.
-
Product
Relay Buddy
190
-
Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
Product
Dual Channel Tri-Level Driver Card
40465
-
Two channels of 10MHz drivers, that can be operated as standard Two-Level Drivers or operated as two channels of Tri-Level Drivers. In the Two-Level mode, the input to each driver channel requires one channel of TTL level timing. Tri-and four level modes require a second clock input. In the Tri-Level Mode, the output from lowest rail to high rail can be 18.5V. Like the 40460 the rise and fall time as well as the high and low voltage levels of each channel is programmable.
-
Product
Automatic Relay Test Set
MT2000 Series
-
Portable single phase dual current manual and automatic relay test set. Readymade test modules. Independent control of Phase angle, frequency and amplitude.
-
Product
Optocoupler and Relay Cards
-
For easy connection and galvanic isolation of digital input or output signals, we offer various optocoupler and relay boards.
-
Product
PXI 6U Power Relay Module
-
The SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC. The module is built on a single width 6U PXI module and the interface is via a standard PXI/CompactPCI backplane. Connection to the switching contacts is via three 50-pin D-type male connectors mounted on the front panel. These are machined contact types with 7.5A current carrying capacity.
-
Product
Low Profile PCI 8 Reed Relay Output
8012H
-
Optimized for sensing 24V inputs, the 8012H Low Profile PCI digital interface provides eight Reed relay outputs (SPST) and eight optically isolated inputs supporting 10-30V. Reed relays are well suited for low current applications. The relays are normally open, and close when energized. The board is MD1 Low Profile and Universal Bus (3.3V and 5V) compatible.
-
Product
Safety Relays
-
*Evaluation units for fail-safe sensors and E-STOP switchgear*Connection of mechanical fail-safe switches and fail-safe sensors*Evaluation systems for safe rotational speed or standstill monitoring
-
Product
Virtual Serial Port Driver
-
The main goal of Virtual Serial Port Driver by Eltima Software is creating virtual COM port pairs. Virtual serial ports created in VSPD behave as if they were real ports and are taken for the real ones with the serial applications. Via these ports serial applications can communicate with each other and transfer data via virtual null-modem cable. The data written to one virtual serial port can be instantly read from the other. Virtual serial ports created in VSPD support all serial port settings, strict baudrate emulation, HandFlow control and signal lines. After virtual COM port pair was created, one can see these ports in Device manager, moreover these ports are available automatically at system startup, even prior to logon. Virtual Serial Port Driver is available in a GUI version as well as a driver version with API for those who are going to use it in their own product.
-
Product
Relay I/O Module via Ethernet
2650
-
8 form-C mechanical relays with 240VAC, 2A ratingConnects to an Ethernet through 2601 hub100 mm DIN carrierResponds to interlock and E-stop circuitsWatchdog TimerCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
Product
PXI Ultra High Density Reed Relay Matrix, 33x16, 1-Pole
40-542A-021
-
The 40-542A-021 is part of a range of ultra high density matrices. The 40-540A/541A/542A are the world’s highest density single slot PXI reed relay matrix modules and are available as a 132x4, 66x8 or 33x16 matrix with 1-pole switching.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 26.5GHz, 50Ω, SMA, Remote Mount
40-780B-532-E
-
The 40-780B-532-E (PXI) and 42-780B-532-E (PXIe) are dual SPDT 26.5GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Relay Test System
-
Relay test products that combine a flexible hardware architecture with advanced test software. Relay tests can be constructed within minutes and displayed using a very simple interface, making the system ideal for low-cost production applications.
-
Product
SUPER-LIGHT Protection Relay Testing Equipment
L336i
-
Protection Relay Testing Equipment has long been associated with the heavy weight and the large size. So carrying the relay testing set to work site seems to be the job of engineers who are physically strong.
-
Product
Phase Sensors and Phase Sequence Relays
-
Protect aircraft equipment & other devices from damage due to phase loss or reversal with DARE?s phase sensors & monitors. Designed to monitor the phase sequence of three phase power, DARE?s phase sensors will protect electrical equipment that is sensitive to incorrect phase sequence (rotation), phase loss, or phase reversal.
-
Product
Trip & Auxiliary Relays
D Series
-
Direct switching power relays designed for heavy duty applications in demanding markets.
-
Product
Relay Test Jumper Kit II
60610
-
Set includes four jumpers to fit many popular relays on Honda, Nissan, Toyota, newer Ford and GM mini micro relays as well as International trucks. Set comes in blow-molded case for storage. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using grey four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on.
-
Product
Safety Relay, 4 Contacts, 10A
D-BW
-
The D-relays series are designed for demanding industrial applications such as power utilities and petrochemical industries. The construction of the relay and choice of materials makes the D-relay suitable to withstand corrosive atmosphere, low and high temperatures and vibrating environments. No external retaining clip needed as integrated ‘snap-lock’ will hold relay into socket under all circumstances and mounting directions All relays are equipped with a LED and suppression diode.
-
Product
16-Ch Isolated Digital Input And 16-Ch Relay USB 3.0 I/O Module
USB-5862
-
USB 3.0 SuperSpeedDaisy chainable by built in USB hub16-ch Isolated Digital Input and 16-ch Form A-type Relay OutputWide input voltage range (10 ~ 30 VDC)High-voltage isolation on input channel (2,500 VDC )Quick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
2x (1 to 8) 50 Ohm 2.5GHz Mux with Self Test Relays
YAVAM308
-
5x (1×4) Mux + 2x Pass trough30Vac/dc, 10W MaxSelftest functionMax current 500mACAN Control (or Ethernet with Ethernet to CAN Gateway)Reflexive
-
Product
Motor Management Relay
269Plus
-
The 269 Plus is a microprocessor based product designed to providecomplete and accurate protection for industrial motors and their associated mechanical systems. The 269 Plus monitors the rotor and stator winding temperatures and shuts off the motor when thermal limits are exceeded.It also shuts down the motor when it detects a potentially damaging orhazardous condition. All RTD inputs not used for stator winding protectioncan have individual settings for temperature monitoring functions.
-
Product
Relay Test Equipment
MC3000 Series
-
MC3000 is recently developed relay test equipment. There are 3 sub-models, MC3000A, MC3000B and MC3000C. They are low cost oriented, aimed to provide customers cheap and cost-effective products.
-
Product
PCI 8 Reed Relay Output / 8 Isolated Input Digital Interface
8012SH
-
The 8012SH is Universal Bus (3.3V and 5V) compatible and ships with the standard size PCI bracket to allow installation in a full-size PCI slot. If you have a Low Profile PCI slot, order the 8012H. The inputs on the 8012SH are rated for 10-30V. For 3-13V inputs, order the 8012S.
-
Product
Relay / Magnetic Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
Product
PXI Ultra High Density Reed Relay Matrix, 132x4, 1-Pole
40-540A-021
-
The 40-540A-021 is part of a range of ultra high density matrices. The 40-540A/541A/542A are the world’s highest density single slot PXI reed relay matrix modules and are available as a 132x4, 66x8 or 33x16 matrix with 1-pole switching.
-
Product
2 Pole 12 X 4 Low Thermal Relay Matrix Module
DP-cPCI-4113
-
A matrix is the most versatile switch topology. It is made up of rows and columns that connect any input to any output. With matrix switching system, it is easy to connect a number of instruments or sources to various test points of the UUT. The benefit of matrix switching is simplified wiring with which the overall test system can easily and dramatically change the internal connection paths without any manual intervention.DP-cPCI-4113 offers switching matrix in a single slot 6U sized cPCI module with flexibility to configure for 48 cross-points or 72 cross-points on factory selectable basis.
-
Product
Drivers
-
Electro-Optical Products Corp.
EOPC offers a full line of drivers to electrically drive EOPC products. Drivers come as housed units powered from line voltage (110 VAC and/or 220 VAC) or as printed circuit boards.
-
Product
Multi-phase Relay Testing
-
Our aim is to make simpler the complex task of 3-phase relay testing. Our comprehensive and intuitive relay software speeds up testing times with a vast library of pre-defined test regimes or manual operation.
-
Product
Lens Driver Components
-
Analog Devices offers a range of lens driver solutions for camera modules in camera phones, camera enabled handsets, DSCs, consumer entertainment, and computer imaging. Lens drivers integrate drivers, waveform control, power management, signal processing, travel control, and more to provide the smallest, lowest power, most complete system solutions with the latest motor/actuator technologies.
-
Product
Miniature Instantaneous Relays
CU-B Series
-
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads. Integrated magnetc arc blow-out function.
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
-
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
