POST Cards
read BIOS error codes during a Power On Self Test for computers unable to boot-up.
See Also: Cards, Extender Cards, Probe Cards, Test Cards, PCI Diagnostic Cards, Post Codes
-
Product
Isolated Digital Input/Output Card
PCI-IDIO-16
-
The PCI-IDIO-16 is a low-cost, 6.8" card that provides isolated input and output for PCI-bus computers. The card has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen isolated FET outputs. For safety reasons in working with AC voltages, insulating shields are provided with each card.
-
Product
Optics Height Adjuster and Post
10785A
Accessory Kit
The Keysight 10785A Height Adjuster and Post is used to precisely position optics devices associated with the 5530 Laser Calibration System, such as the 10766A Linear Interferometer. The height adjuster and post also facilitate adjustments in measurements such as pitch and yaw.
-
Product
PCI/PCIe Card
MDA16-4i
-
For optimal adaptation to a measurement task, the PCI/PCIe cards from BMC Messsysteme GmbH can be supplemented with various modules. Due to the low latency of the PCI/PCIe interface, the MDA16-4i output module is particularly suitable for analog control and regulation tasks.
-
Product
PCI Express Card
EXC-4000PCIe/xx
-
The EXC-4000PCIe/xx card for the PCI Express bus supports up to four dual redundant 1553 channels using the M4K1553Px(S) module and is compatible with all common variations of MIL-STD-1553 (A, B).
-
Product
Multiplexer Switch Cards
-
The Adapt-a-Switch® multiplexer switch cards deliver high performance and high density for your microwave switching applications.
-
Product
Reflective Memory PCIE card
PCIE-5565PIORC
-
The PCIE-5565PIORC low profile PCI Express (PCIe) Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board may be configured with 128 MB or 256 MB of onboard SDRAM.The local SDRAM provides fast Read access times to stored data. Writes are stored in local SDRAM and broadcast over a high speed fiber-optic data path to other Reflective Memory nodes.
-
Product
Multi-Protocol Serial Card
PCM485
-
The PCM485 is a multi-protocol serial card that supports RS-422 or RS-485 communications in a single 5V PCMCIA Type II card. The PCM485 uses a crystal controlled oscillator which permits precise selection of baud rates from 50 to 115,200.
-
Product
PCI Card with input channels
PCI_LVDS_8R
-
The PCI_LVDS_8R has 8 channels of LVDS input. The channels are grouped two per Filter Xilinx. The input data is filtered, then written to the Input FIFO. There is one Input FIFO per LVDS channel. 1K x 32. One Latch Xilinx handles 4 LVDS channels. The data is read from the Input FIFO by the Latch Xilinx and either written to the SDRAM or the Output FIFO.
-
Product
16-Channel DAC Function Card
ProDAQ 3510
-
The ProDAQ 3510 DAC function card is a ProDAQ high-density card that fits into ProDAQ VXIbus motherboards and LXI function card carriers. This high-density card contains 16 independent, 16-bit DAC channels, and each channel is equipped with its own DAC. The ProDAQ 3510 DAC function card is specially designed for DC, low-frequency, and current loop applications.
-
-
Product
Capacitance Simulation Card
SET-1220
-
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
Product
PC Card
MAXPCIe 502
-
The MAXPCIe 502 carrier board is a high performance, modular multi-protocol PCI-Express solution to your tests and simulation requirements, supporting one or two MAX Technologies mezzanine I/O modules. It is powered by a 800MHz RISC processor and 16MB of shared memory, permitting it to buffer and process communication with the host computer.
-
Product
XMC Display Control Card
XM61002
-
LinkedHope Intelligent Technologies Co.,Ltd.
XM61002 is an XMC display control card independently developed by Linghao Intelligent®. It is mainly targeted at high-performance embedded graphics image processing and GPU general computing processing (GPGPU) applications.
-
Product
32CH 4-20mA Current Sink Card
SET-1250
-
Each channel provides an isolating relay and a short-circuit MOSFET with which opening and short-circuit errors can be simulated. The short-circuit MOSFET has overcurrent protection with integrated current limitation.
-
Product
Power Interface and Prototype PXI Card
GX7404
Interface
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
PCI card with 3 IP sites
PCI3IP
-
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
Product
OpenVPX card
NPN244/NPN244S
OpenVPX
The NPN244 6U VPX is a high-performance computing & GPGPU OpenVPX card that hosts dual GPUs with alignment to the VITA-65 standard. Based on the NVIDIA® Turing™ architecture using either the NVIDIA® Quadro RTX™ 5000 platform or NVIDIA® Quadro RTX™ 3000 platform, the NPN244 offers exceptional graphics and GPGPU compute capability with CUDA® support, AI, and deep learning.
-
Product
PCI Express Mini Card
mPCIe-UCAN2 & mPCIe-UCAN2-ISO
-
The mPCIe-UCAN2 card features two CAN ports that instantly install in most any operating system as standard COM/ttyS devices. Each port supports CAN2.0 A/B and FD operations including data rates up to 10Mbps and timestamps with 1μs (or 1ms) resolution. These CAN ports can be controlled using a simple ASCII command/response interface using a superset of the popular CAN232 standard (extendedto support CAN FD requirements)
-
Product
IPMI Card
AX93338
-
IPMI specification is an Intel® lead standard. The AX93338 follows IPMI 2.0 spec. System administrators can remotely monitor system health and manage the system using Web page or KVM. The AX93338 operates independently operating system allowing administrators to manage system remotely even the device failure.
-
Product
Digital Signal Processor Card
CHAMP-FX2
-
Curtiss-Wright Defense Solutions
Utilizing a 6U VPX-REDI form factor, the CHAMP-FX2 FPGA-based computing platform harnesses the tremendous computing power of two Xilinx Virtex-5 FPGAs, combined with the high-performance floating-point capabilities of the NXP (formerly Freescale) MPC8641D dual-core Power Architecture processor and the performance and flexibility of a Serial RapidIO switching fabric to flexible computational performance.
-
Product
Signal, Contact, Receiver, TriPaddle, 5 Amp, .025" Round Post
610110179
Signal Contact (Receiver)
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
Product
Card shaped DC power supplies
RK-80 Series
-
Touch and feel the compactness of RK80 series. Quite convenient to bring from lab to lab, and even you need various different supplies RK80 supplies still save spaces on your desk. Output range selectable function (3 different output range) saves also your investment minimum. As these supplies have digital communication function by integrated microcomputer, it is also easy to built network with other equipment for automation.
-
Product
Card Impact Tester
-
Tests corner impact and card bending resistance, Designed to test for MasterCard CQM and ANSI N322 requirements, Easy to use, Repeatable results, Small footprint design for benchtop use, Adjustable jaws allow use with various card thicknesses, Super heavy duty custom CNC design
-
Product
Utility Card: Flash Programming Applications
-
This new feature enables the Keysight Medalist i3070 ICT to perform higher speed flash programming at the ICT station in the printed circuit board assembly manufacturing line. You can combine programming and testing into a single phase, to save time and money. This in-system programming (ISP) flash solution is tester-based and does not rely on fixtures, thus enabling greater flexibility and ease of debugging.
-
Product
Rack and Card Base
SERIES 5000
-
Series 5000 is a rack based terminal equipment solution which is user configured with any mixture of CardModules from our extensive range of available solutions.
-
Product
Data Acquisition Card
TPCE
-
The Elsys TPCE data acquisition (DAQ) cards are high-precision and high-resolution digitizers with sophisticated features such as advanced trigger mode, continuous data acquisition mode, differential inputs, digital input lines (Markers) and ICP coupling for powering piezo sensors.
-
Product
PCIe and PCI Avionics Interface Cards
Interface
Ballard PCI Express (PCIe) and PCI Avionics Interface Cards enable computers to interface with a variety of avionics databuses for testing, validating and simulating commercial and military avionics equipment and systems.
-
Product
VPX GPGPU Processor Card
VPX6-4944
-
Curtiss-Wright Defense Solutions
The rugged VPX6-4944 dual NVIDIA Tesla Pascal GPU processor board is designed and manufactured by Wolf Advanced Technology. This board is part of a family of GPGPU modules available from Curtiss-Wright Defense Solutions to enable development of High Performance Embedded Computing (HPEC) systems.
-
-
Product
Smart Card Testers
CT1000
-
The CT1000 testers are open and configurable to test any kind of communication protocols used on smart cards, and to be updated for new technologies. The systems can test devices that use common standard protocols (as ISO 18000, EPC Global Gen 2, ISO 14443, ISO 15693, MIFARE™, DESFIRE™, FeliCa™, ISO 11784/85, ICode™, Hitag™, ISO 7816, ISO 7813), and are ready to test also the next generation of cards protocols, such as: USB-Keys, MMC, Micro-SD (with and without CPU inside), M-SIM, HD-SIM, SIM-WAVE, and I2C.
