Harness
A multi-routed assembly of connectors, wire and cables.
See Also: Cable Assembly, Harness Test, Test Harness, Wiring, Wire, Connectors
-
Product
Harness Testers/Thickness Gauge
-
Our Hardness Testers/Thickness Gauges includes premium models such as the EMHT40, UTEMHT20 and UTEGEMTT2. These testers are precision instruments designed to measure the thickness or hardness of most metals. Two cost effective units - FHT801 and FHT803 are tailored to agricultural applications such as checking the ripeness of fruits and vegetables in fields/warehouses.
-
Product
Automatic High Voltage Wire Harness Testers
-
Automatic high voltage wire harness testers are used in a variety of industries, such as aerospace and defence through to rail, and are used to test any equipment which contains a high number of electrical wires, or active components ensuring these pass specified test criteria at the sub-assembly and final stages of construction. These systems ensure the wiring and components are 100% compliant and undamaged, recording every test measurement and aiding diagnosis of detected faults.
-
Product
Guided Assembly | Cable Harness Testers
Autobuild™ Software
-
Our optional, add-on AutoBuild™ software (Item 728) offers Guided Assembly for cables and wire harnesses. Use a supplied probe, or a finger with wrist strap, to touch an unterminated wire and the software shows (and says) exactly where the wire should be connected. As the operator attaches each new wire, AutoBuild checks the entire assembly and provides a clear checklist showing all completed good connections.
-
Product
Connector Board for Cable and Harness Tester
CB49
-
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
Product
Cable and Harness Tester
CHT
-
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
Product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
-
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
Product
Wire/Cable Harness Analyser
-
Qmax Test Technologies Pvt. Ltd.
Wire/Cable Harness Analyser by QMax
-
Product
Threaded Probes Designed for Connector and Harness Test
-
Equip-Test Threaded Probes Designed for Connector and Harness Test
-
Product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
-
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
Product
3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end
GT97107
-
3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
3 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97102
-
3' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
Harness Design and Manufacture
-
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
Product
Cable Harness Test System
-
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20,000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
-
Product
6 Ft Harness, 78 Pin Male Connector On One End, Loose Wires (numbered) On Other End
GX96105
-
6 ft harness, 78 pin male connector on one end, loose wires (numbered) on other end.
-
Product
1' Harness, 50-Pin Male D-Sub Connector on one end, loose wired (numbered) other end
GT97106
-
1' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
-
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
1 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97103
-
1' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
-
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
Product
Ultrasonic Metal Welding
-
Ultrasonic metal welding method is used to join dissimilar metals of aluminum wire and copper for aluminum harnesses, thin copper alloys for vapor chambers and hoop materials, and aluminum laminated foil for rechargeable batteries.
-
Product
kSA BandiT PV
-
Harness the power of this patented technology to improve your process control. Measure and control uniformity, thickness, band gap, temperature, surface roughness and more.
-
Product
Spring Contact Probes
-
FEINMETALL offers a wide range of contact probe:ICT / FCT probes, short travel probes, double plunger probes, fine pitch probes, interface probes, wire harness probes, threaded probes, high current probes, switch probes, twist proof probes, push back probes, koaxial probes, radio frequency probes.
-
Product
Cable Tester
SS8681 Series
-
The SS8681 series cable tester is used for test and measure wire cable harness, wire harness, like as: auto cable, audio cable, power cable, network cable, telephone cable, USD cable, HDMI cable, video cable, etc.
-
Product
High Speed Contacts
-
Our quadrax, twinax, spring probe, coax, triax and fiber optic contacts can be sold seperately or configured into any of our standard connector shells sizes as well as cable assemblies and harnesses.
-
Product
Smart Bench Essentials Digital Multimeter
EDU34450A
Digital Multimeter
The Keysight EDU34450A is a modern benchtop digital multimeter (DMM) that is part of the Keysight Smart Bench Essentials (SBE) Series of four unique instruments that harness one powerful graphical interface to connect, control, and capture measurement data. It features 5.5 digits of resolution and up to 110 readings/s measuring rate for speed-critical tests
-
Product
Mechanical Tester
UMT TriboLab
-
Bruker’s Universal Mechanical Tester (UMT) platform has been the most versatile and widely used tribometer on the market since the first model debuted in 2000. Now, newly designed from the ground up, the UMT TriboLab™ builds on that legacy of versatility with a unique modular concept that harnesses more functionality than ever before—all without any compromise in performance.
-
Product
Cable Harness EM Solver
MHARNESS
-
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
Product
Cloud Manufacturing Software
-
Technology and automation are driving the next generation of manufacturing. Leading organizations are harnessing the cloud to transform the way they work – and you can too by:
-
Product
COM-HPC Server Type Development Kit based on Ampere® Altra® SoC
Ampere Altra Dev Kit
Software Development Kit
Ampere Altra Dev Kit consists of a COM-HPC Server Base carrier paired with a COM-HPC Server Type Size E module and heatsink with fan. The module features Ampere® Altra® SoC (Arm Neoverse N1-based architecture) harnessing 32/64/96/128 Arm v8.2 64-bit cores for up to 1.7/2.2/2.8/2.6 GHz and providing support for up to 768GB DDR4 memory, offering unprecedented performance and power per watt with exceptional scalability.
