Link
See Also: Camera Link
-
Product
Low Profile PCI Express 4-Port
7406e
-
The 7406e low profile PCI Express serial interface provides four RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
Model LGF2: Gypsum Moisture Meter
MRC006522-2
-
Two-range version of the Model LFG. Has 1/2 the normal sensitivity, allowing off-scale indications to be accurately read. Includes carrying case, NiMH battery and operating instructions book. Additional details can be found in product link.
-
Product
PCIe-8398, x16 Gen3, PCI Express Host, 13.6 GB/s Device for PXI Remote Control
784179-01
Remote Control Interface
The PCIe-8398 is a host interface card used to control a PXI Express chassis over a software-transparent PCI Express Gen 3 x16 link. The PCIe-8398 is installed into a x16 PCI Express slot of a desktop or rackmount PC and is connected to a PXIe-8398 or PXIe-8399 PXI remote control module using Gen 3 x8 copper cables.
-
Product
Digital Data Link
-
SUAS DDL™ is small size, lightweight, and low power bi-directional, digital, wireless video link. Compliant with the Small Unmanned Airborne Systems Digital Data Link (SUAS DDL) waveform, it can also be used to enable enhanced command and control of small UAS. DDL is IP-based to enable maximum flexibility and interoperability between small airborne and ground systems with limited power availability, and bandwidth to maximize the number of systems that can operate within an area.
-
Product
Advanced Ethernet Tester
LinkRunner® 10G
-
Quickly test, verify, and troubleshoot 1Gig, Multi-Gig and 10Gig Ethernet (copper, fiber) including line-rate performance testing and packet captureLayer 1-7 AutoTest enables any technician to find network problemsMonitor networks for intermittent issues, every minute for up to 24 hours AllyCare-enables in-depth network discovery features and web remote controlLANBERT™ Media Qualification app tests the capability of premise cabling and media components for carrying Multi-Gig and 10Gig EthernetTwo LinkRunner 10G units can be used for line-rate performance testing to verify network capacity, performance and QoS, as well as service provider SLAs between sites
-
Product
Amplifier Modules Broadband
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
AC Line Harmonics Analyzer Including Flicker Analysis With UK, Schuko Or US Socket.
HA1600A
-
Compliance quality measurements to EN61000-3-2 and EN61000-3-3Measures peak or rms voltage or current, real or apparent power, power factor, phase etc.Tabular/histogram of 40 harmonicsVoltage/current waveforms displaysContinuous analysis with real-time graphical updateWide range of power connectors available320 x 240 pixel high-contrast displayUSB, RS232 and printer interfaces fittedPC control and documentation software supplied (HA-PC-Link+)
-
Product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
PXI 2A Multiplexer, 1-Bank, 8-Channel, 16-Pole
40-614C-019
Multiplexer Module
This 1-bank, 8-channel, 16 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Ionic Contamination Test Systems
CM+ Series
-
The Contaminometer (CM+ Series) system was originally developed by Protonique, the business of industry guru Brian Ellis. They also featured in the early development programmes of "cleanliness measurement" carried out by the US Department of Defense at China Lake in the 1970s. Historically, International Standard IPC-J-STD001 stated that assemblies be cleaned to a value of <1.5µg/cm2 of NaCl equivalence. However, the new design is linked to the introduction of the new process control metric introduced by Gen3 Systems: Process Ionic Contamination Testing. The CM+ Series measure the amount of ionic contamination in accordance with all existing test methods, often referred to as ROSE testing, as well as the new PICT test.
-
Product
Boundary-Scan DIMM Socket Tester
ScanDIMM
-
Maximizing test coverage is an important piece in test procedure development. Unfortunately, not all designs have the necessary requirements in place to accommodate boundary-scan test methods on memory devices. ScanDIMM digital socket test modules are designed to overcome such limitations when testing DIMM sockets utilizing boundary-scan test techniques.ScanDIMM modules provide the capability to instantly turn any DIMM socket into a fully compliant IEEE-1149.1 device. Integration is as simple as assigning the included BSDL file to the reference designator of the target socket and compiling test vectors.In multi-socket systems, multiple ScanDIMM modules can be linked to provide even greater boundary-scan test depth.
-
Product
16-CH Discrete Input 16-CH Discrete Output Daughter Board Module
HSL-DI16DO16-DB-NN
Strain/Bridge Input Module
- Slave ID consumption: 1 16-CH NPN sinking type sensor inputs or dry contact and 16-CH - NPN sinking type outputs- Photo couple isolation voltage: 2500Vrms- Input impedance: 4.7KΩ- Input current: ??10mA(Max), ??12.5mA(Peak)- Input voltage: ??40V (Max)- Output switching capacity:300mA/ch at 24VDC- Terminal Base:HSL-TB64 or HSL-TB32-DIN- LED indicator: Power, Link and I/O status
-
Product
Test Accelerometer Sensitivity And Noise Test
Accelerometer Test Unit
-
*Quick and Accurate Accelerometer Test*Battery operation*All tests use 32-bit resolution A to D Converter*All data downloaded to PC via Ethernet link*Records all data to a flexible easy to use database*Records time and date of tests
-
Product
Single Phase 2 Circuit Energy Meter Test Bench Type KP-S1000-B
-
Bofa Instrument & Equipment Co., Ltd
Single phase 2-circuit energy meter test bench type KP-S1000-B, is a new generation, high precision energy meter calibration equipment. It is especially designed for testing 2-circuit energy meter (shunt circuit and CT circuit), open or closed test link (I-P link) both. It is an ideal testing equipment for mass production of 2-circuit energy meter in meter factory. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
BusTools Software Analyzer
AFDX-A
-
BusTools/AFDX-A is a Windows 7/10-based GUI application solution from Abaco Systems that establishes new levels of power, flexibility and ease-of-use for AFDX (Avionics Full Duplex Switched Ethernet) traffic monitoring, analysis and simulation. Available for use with our powerful CNIC interface, BusTools/AFDX offers an intuitive interface to view, log, analyze and generate AFDX network traffic at the Adapter, End System, Virtual Link (VL) and Port levels. Contact Goleta factory for listing of supported products.
-
Product
Cable Testers
LINKMASTER
-
The LinkMaster Tester consists of two units. The main unit is connected to one end of the cable to be tested and the remote unit is connected to the jack at the far end of the cable (wall outlet, patch panel port, etc.)
-
Product
MXG Signal Generators
-
On the path to better performance, the Keysight's MXG signal generators are fine-tuned signal sources in R&D measurements. Whether you’re pushing for a linear RF chain or an optimized link budget, the analog and vector MXG models deliver the performance and capabilities you need: phase noise, ACPR, channel coding, and more.
-
Product
Industrial Ethernet Network
CC Link IE Field
-
CC-Link IE Field network is the first gigabit industrial Ethernet network extended down to the field device level. It combines the best of existing technologies and applies them in a highly reliable architecture that provides exceptional data bandwidth and transaction rates. The new network uses commercially available Cat5E cable and RJ45 connectors.
-
Product
IceMap™
Real Time Ice Thickness Measurement
-
The IceMap real-time display shows the automatically detected bottom of the ice (blue line) in real time. Users can set a minimum thickness warning threshold (gold line). Winter ice roads and bridges are a common transportation link in the northern regions of Canada, Alaska, Europe and Russia. The Sensors & Software IceMap system is designed to measure the ice thickness on these temporary, yet vital, links and ensure the safety of all travelers. The GPR sensor is towed across the ice surface behind a truck or snowmobile and the ice thickness data, displayed in real-time as a cross-sectional image, are sent wirelessly to the operator’s computer.
-
Product
Receivers
-
Pig tracking sensors are utilized to indicate the passage of a pig past a given point in the line. This system can be linked to a SCADA package or simply used to provide an easy to see visual indication.
-
Product
USB License Key
Sentinel RMS
-
For customers that wish to use our software on different computers we offer the possibility to purchase our software license locked to a USB dongle. Add this product to your software order and we’ll deliver your software licenses linked to a compact Sentinel RMS license key.
-
Product
PC Based Power Monitor
11P-Link
-
1P-LINK compact interface box is the choice for users who want to do all power meters control as well as the analysis from their computer. With its impressive features for statistics calculation and display options, the 11P-LINK is also an answer to scientific or OEM users who need a low-cost computer based power monitor
-
Product
8-bank, 16-channel, 1 Pole Version is part of the 40-614C High Density 2A Multiplexer Module
40-614C-003
Multiplexer Module
This 8-bank, 16-channel, 1 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Connector Core Tuner Machine
-
Anfkom International Co.,Limited
Fiber optic connector active link connection loss caused mainly by the following aspects:1.Fiber core2.Horizontal mismatch3.Vertical mismatch4.Axial mismatch
-
Product
Process Improvement Software for SPI & AOI
SIGMA Link
-
SIGMA Link software suite links altogether solder paste inspection (SPI), automated optical inspection (AOI) and manufacturing execution system (MES). For Smart Factories, SIGMA Link is the essential element to connect inspection machines to Manufacturing Execution System. This real-time interface ensures full traceability and enables interlocking of machines to automate SMT lines while driving yield to new levels.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787453-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Vacuum & Leak Detection Software
-
Agilent vacuum and leak detection software and app provide the data management performance needed to meet manufacturing yields, quality-control standards, and compliance requirements in industrial vacuum applications.The powerful Vacuum Link app offers wireless remote pump control, making it easy to monitor your system.A-PLUS software enables the user to control and monitor vacuum solutions.Leak Test Data Wizard software enables powerful tracking and automation of leak detection processes.
-
Product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
42-614D-015
Multiplexer Module
The 40-614D-015 (PXI) and 42-614D-015 (PXIe) 1-bank, 128-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Conversion Tools
Tester Data Link
-
VCD/eVCD to tester conversion (via STIL)WGL/TDL to tester conversion (via STIL)Most flexibility to handle complex devices functionality Support protocol definitionUtilize advanced tester features (Such as Xmode, concurrent test etc’… )High Performance Fast run time
-
Product
PXI MUX 4 Banks of 16 Channel 2 Pole
40-610-022-4/16/2
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
