Couplers
enable a signal to be used in another circuit.
-
Product
Couplers
-
Standard connectors are N-Female. 7/16 DIN-F optional. TX power is input per port.
-
Product
Waveguide Directional Couplers
-
WR-42 to WR-10 waveguide sizes. Split block waveguide versions available. Available in 7 bands including K, Ka, Q, U, V, E, W from 18 GHz to 110 GHz. 30 dB typical directivity. E Bend and H Bend configurations available. 10 dB and 20 dB coupling values are offered.
-
Product
Fused Optical Couplers
-
Nanning Xionghua Photonics Technology
Fused Optical Coupler by Xionghua Photonics
-
-
Product
Directional Couplers
-
Pasternack directional coupler category is passive devices that couple part of the transmission power in a transmission line. Our directional coupler series provides the bandwidth, high directivity and higher power that engineers need for their most demanding application designs. RF directional couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack directional coupler components are RoHS and REACH compliant. RF directional couplers are available with 4.1/9.5, 4.3-10, 7/16 DIN, Type N or SMA connectors. Our directional coupler line has 6dB, 10dB, 15dB, 16dB, 20dB, 30dB or 35dB coupling values. Power ratings of our typical and high power directional couplers range from 25 Watts to 70 Watts. Directional coupler frequency range of this product design is from 1 GHz to 8 GHz. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this directional coupler series is in-stock. Not only are these couplers in directional design in stock, they also will ship the same day as they are purchased.
-
Product
90 Degree Hybrid Couplers To 26.5 GHz
-
Pulsar Microwave manufactures hybrid couplers and dividers from 400 MHz to 26.5 GHz for use in 50-ohm systems. These hybrids are available in narrowband and wideband designs with up to 20:1 bandwidth ratios. Most models are built to handle 100 watts input power. The designs are stripline, and optimized for best matching and isolation performance. Available with SMA or N type female connectors.
-
Product
PhotoIC Couplers
-
Panasonic Industrial Devices Sales Company of America
A Commercialized PhotoIC Coupler For High-Speed Communication Between Industrial Equipment. Panasonic, a worldwide leader in cutting-edge electronic components, has developed and introduces the NEW APS1 Series PhotoIC Coupler that transmits light signals while allowing electrical insulation. This revolutionary new product is designed for high-speed transmission of signals between industrial equipment such as motors and PLCs.
-
Product
Dual (Bi) Directional Couplers
-
Pasternack dual directional coupler (also known as bi-directional coupler) series are passive devices that couple part of the transmission power in a transmission line. Our dual directional coupler components provide the bandwidth, high directivity and higher power that designers need for their most demanding applications. RF dual directional couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack bi-directional coupler items are RoHS and REACH compliant. Couplers that are dual directional from Pasternack are available with SC, SMA and Type N connectors. This dual/bi directional series is offered in 10dB, 20dB, 30dB, 40dB and 50dB coupling values. Power ratings for our dual directional couplers range from 10 Watts to 10 Watts. Frequency ratings for our bi-directional couplers range from 1 GHz to 8 GHz. Like the other over 40,000 RF, microwave and millimeter wave components from Pasternack, our dual (bi) directional coupler series is in-stock. Not only our these couplers in stock, they also will ship the same-day as they are purchased.
-
Product
1553 Bus Cables, Couplers, Terminators, and Kits
Terminator
Please review 1553 Bus Accessories to the right. You can also use the Login-Download link above (login required) to access all the Hardware Manuals with specific cable and connector information. Most 1553 Cards and ENET devices have optional 1553 Jack and AUX I/O DB cable assemblies. Please see the respective product pages part numbers tab. Most ARINC products include flying-lead cable assemblies.Please use the Contact link to email/phone sales for a login as needed.
-
Product
RF Couplers
-
Directional, bi-directional, dual-directional and RF Taps; over 475 models with power handling from 0.5 to 300W covering DC to 65 GHz!
-
Product
VHF & UHF Couplers for the PowerMaster and PowerMaster II
-
VHF-1.5K (2m), VHF-1.5K-2 (1.35m), UHF1.5K (440-450 MHz), UHF-1.5K-2 (420-440 MHz)
-
Product
3x3 1x1 2x2 1x2 Couplers
-
Couplers can be used to split light from one or more fibers onto two or three fibers or to combine light from two or three fibers onto one or more fibers.
-
Product
3x3 and 2x2 High NA Couplers
-
Feasa produces a range of Couplers Manufactured from high Numerical Aperture (NA) 80 micron fiber. High NA fiber has low bend attenuation compared to standard singlemode fiber.
-
Product
Directional Couplers From 0.01 To 2000 MHz
-
Pulsar Microwave's low frequency directional couplers operate within the frequency range of 10 kHz to 2 GHz. They're available in either surface mount or connectorized designs. SMA female connectors are standard, but BNC, TNC, F, N, jack or plug are available upon request.Most of these directional couplers have a flatness of +/- 0.25 dB and directivity of 20 dB or better within the operating band. VSWR of 1.3:1 or better maintained on all ports for most models. Maximum power handling is between 1 and 3 watts depending on model.
-
Product
Couplers, Repeaters, Bus Switches, Connectors, Cables & More
-
Accessories for the MIL-STD-1553 data bus are as much of an interface as the communication card. Therefore at Excalibur we provide a full line of accessories for the MIL-STD-1553 data bus that include, Box/Inline Couplers, Repeaters, Bus Switches, break out boxes, connectors, terminators, transformers and custom cable assemblies. Excalibur uses only premier quality parts from known manufacturers. We constantly test our products to meet our higher standards.If you have a need for an accessory product for your card and it is not listed please contact us to see if it is a product we should be supporting.
-
Product
Telecom Fiber Couplers
-
Thorlabs offers a varied selection of single mode (SM) and polarization-maintaining (PM) fiber couplers, as well as single mode 1x8 and 1x16 PLC waveguide splitters that have center wavelengths at common telecom wavelengths, including 850 nm, 1310 nm, and 1550 nm.
-
Product
6-8 DB Directional Couplers From 0.5 To 40 GHz
-
Pulsar Microwave manufactures the CS06 and CS08 series single directional couplers in nominal values of 6 and 8 dB, respectively. These directional couplers are used in 50-ohm systems for narrow and wideband applications within 500 MHz to 40 GHz. Standard outlines are fitted with SMA or N type female connectors, but Pulsar Microwave can customize upon request.
-
Product
Directional Couplers & Bridges
-
A complete line of coaxial single and dual port directional couplers, and bridges for isolating, separating, and combining RF and microwave signals in such applications as power monitoring, source leveling, swept transmission and reflection measurements.
-
Product
Couplers
-
Macom Technology Solutions Holdings Inc.
MACOM’s couplers are used extensively in a wide range of aerospace and defense, wireless, and wireline communications applications. Our directional and hybrid couplers are offered in a variety of connectorized and surface mount packages with a broad range of coupling values ranging from 6 to 30 dB. Operating at frequencies from 2 MHz up to 18 GHz our couplers are ideal for real-estate constrained customers who need a high performing device for easy assembly.
-
Product
Fuel Injection Pressure Tester w/2 Gages & Quick Couplers
53950
-
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
Product
Fuel Injection Pressure Tester with Quick Couplers
53900
-
Quick couplers provide for fast and easy hook-up. Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI. Use on Ford older TBI systems not equipped with small Schrader test valve. Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR). Supplied with instructions in a vinyl pouch.
-
Product
Couplers (Quadrature, 180, Directional)
-
PMI offers the highest quality quadrature couplers for commercial and military applications in the frequency range of a few MHz to 40 GHz. If you do not see exactly what you need, please email your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
Product
2x2 Interferometric Couplers
-
Feasa manufactures a series of couplers, which are optimised for use in fiber interferometers. The couplers have a highly reflective end on one or more output ports and can be configures as 1x2 or 2x2.
-
-
Product
High-Speed CMOS Output
-
High-speed CMOS output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a CMOS output IC on the output side. This coupler is a high common mode transient immunity (CMR), high-speed CMOS output type device designed for high-speed logic interface circuits.
-
Product
Cross Needle Meter. 1.8 - 60/144/440
MFJ-864
-
This new MFJ Cross Needle SWR/Wattmeter covers HF thru VHF 1.8 - 60MHz, 144 MHz and 440 Mhz bands. It features separate HF and VHF / UHF directional couplers, each with its own SO-239 connectors. This lets you connect your HF and VHF/UHF transceivers at the same time.
-
Product
Cylinder Leakage Tester Kit
CLT200
-
Quickly locates internal engine problems such as bad rings, valves and leaking head gaskets. Dual 2-1/2" heavy duty gauges with protective outer boots. Scales read 0-100psi and 0-700 kg/cm2Pressure regulated manifold includes high quality quick couplers for fast set-ups.
-
Product
PD Coupler
-
Techimp Capacitive PD Couplers offer both the PD and sync signals references, allowing a thorough investigation of the signal originating inside the asset they are connected to.Techimp Couplers are individually tested according to the following international standards: IEC60358; IEC60694; IEC60270.
-
Product
Digital RF Power Monitor
3024
-
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
Lange Couplers
-
The Lange Coupler is a four-port interdigitated structure originally developed by Dr. Julius Lange in 1969. They are a common RF/microwave circuit. The coupling is derived from closely spaced transmission lines, such as microstrip lines. With the introduction of Ion Beam Milling, SemiGen’s ability to consistently produce Lange Couplers with lines and spaces as small as 10 microns and controlled to tolerances of +/- 1 micron is a direct result of our anisotropic ion beam etching process.
