Digital Voltmeters
Measure voltage, displaying the measurements in numeric value on a digital display.
-
product
Digital Voltmeters
*Measures voltage from 5V to 25kV line to line*Large, easy to read LED display*Versatile for overhead and underground applications*Capacitive Test Point and Peak Hold modes
-
product
3 Digit LCD Voltmeter
DPM 2000
The DPM 2000 is a 3 digit LCD voltmeter with 12.5mm (0.5") digit height. It features 200mV d.c. full scale reading, a bandgap reference, auto-zero, auto-polarity and a set of annunciators. The meter plugs directly into a DIL socket or can be panel mounted using the bezel and window. Connection to the meter is via two rows of pins.
-
product
3 Digit LED Voltmeter
SP 300
The SP 300 is a 3 digit LED voltmeter with 9mm (0.36") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into an 8-way SIL socket and can be fitted into a panel via the fixing clip. Splashproof protection to IP65 is achieved by fitting the seal supplied.
-
product
Wide-range Programmable DC Power Supply
IT6900A Series
IT6900A series wide range programmable power supply have built-in standard RS232, USB, GPIB, RS485 and analog interface (RS485 and analog interface are just for IT6900B), support SCPI protocol, facilitate remote control, industrial PLC control and the formation of intelligent test platform. Remote compensation terminals avoid the problem of inaccurate testing caused by voltage drop on the wire.Low ripple, low noise and built-in digital voltmeter make IT6900A easy to do external measurement.IT6900A can be widely applied in DC-DC power supply module, battery charging and sensors and other test areas.
-
product
Arc Ingintion Tester
The product is designed to carry out Arc Ignition Test as per IS/IEC 60947-1 Clause 8.2.1.1.2 (material used for electrical products). The adjustable current source is 230V AC @ 33A. The load is adjusted to get 32.5A at 0.5 power factor. Included on control unit are Digital Voltmeter, Digital Ammeter, Digital Power Factor Meter and Micro Controller based programmable Sequence Timer with LCD display for display & setting. The arrangement is made to mount the test piece with electrodes as per the specification given in the standard.
-
product
Earth Contact Resistance Tester
SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.
-
product
Mobile Comm DC Source w/ Battery Emulation, DVM
66321D
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321D mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321D mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads. The 66321D dc source provides all of the capabilities of the 66321B with the addition of a built-in digital voltmeter.
-
product
Handyscope TP450-50XM-W5
TP450-50XM-W5
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
product
Ultra Low Level DC Voltage Amplifiers
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
product
Programmable Multifunction Generator
IST 5800/5850
IST Information Scan Technology, Inc.
The IST-5800 series programmable multifunction generator is an exceptionally versatile and economical instrument for applications in R&D, Manufacturing Test, Service Repair and Training. Featuring an adjustable triple output power supply and waveform generator, it has the ability to provide power and signal sources for a circuit while the universal logic probe, auto-ranging frequency counter, and digital voltmeter allows you to simultaneously analyze and measure circuit activity.
-
product
5.5mm (0.22") Digit Height
DPM 1AS-BL
The DPM 1AS-BL is an ultra-miniature 3 digit LCD voltmeter with 5.5mm (0.22") digit height and LED backlighting. It features a negative rail generator which enables the meter to measure a signal referenced to its own power supply GND.
-
product
Programmable DC Power Supply
IT6100 Series
IT6100 series assure you accurate measurements with 0.1mV/0.1mA high resolution and high accuracy. With high-speed List mode output and voltage rise speed up to 20ms, it can independently edit and perform the default voltage waveform to meet the high-speed test needs. IT6100 series has built-in 5 1/2 digital voltmeter and milliohm meter, which can measure additional signals. IT6100 series supports SCPI communication protocol, GPIB/USB/RS232 interfaces are optional for customers.
-
product
3 Digit LED Voltmeter
DPM 340
The DPM 340 is a 3 digit LED voltmeter with 8mm (0.31") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into a SIL socket or can be snapped into a panel. Connection to the meter is via a single row of pins
-
product
3 Digit LCD Voltmeter
V 1
The V 1 is a very low cost 3 digit LCD voltmeter with 6.3mm (0.25") digit height, intended for high volume OEM applications. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into two SIL sockets or can be panel mounted using the bezel provided. Connection to the meter is via two rows of 4 pins.
-
product
Digital AC milli Volt meter
PGP Electronics Private Limited
PGP Electronics Digital AC Mill voltmeter is a very versatile and general purpose equipment for the measurement of audio frequencies. It is useful in measuring low amplitude signals over a wide band of frequencies with precision. Its has a wide band width and sensitivity is 10uV. This instrument is useful for all amplifiers/ audio system manufacturers, college laboratories to measure input/output of any amplifier as well as frequency response of that amplifiers. .
-
product
Temperature Rise Test Panel
2000A
SCR ELEKTRONIKS have developed “TEMPERATURE RISE TEST BENCH FOR MEDIUM VOLTAGE SWITCH BOARDS” to measure rise in temperature at various points as mentioned in standard at junctions. The set-up consists of a True RMS Constant Current Source (to maintain the Current within + / - 1 % of set value with Digital Indication), PC based control system, Temperature data logging on PC, Servo-Controller and other indications. Digital voltmeter Primary Voltage) indicates the position of auto transformer (variac).
-
product
Jandel Test Unit
ResTest
The new Jandel ResTest Test Unit is a constant current source and digital voltmeter with large colour screen, supplying constant currents between 1uA and 10mA, and measuring voltages from 0.04mV to 4000mV.
-
product
Digital DC Micro Volt meter
PGP Electronics Private Limited
PGP Electronics Digital DC Micro Voltmeter is a precision measuring tool for the measurement of low DC Voltages. This unit can measure low DC voltages, typically in the order of Micro Volts. This instrument is designed to with stand rugged operation.
-
product
3 Digit LED Voltmeter
DPM 40
The DPM 40 is a 3 digit LED voltmeter with 11mm (0.43") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter can be panel mounted using the bezel and window. Connection to the meter is via two rows of pins
-
product
0-600 Amp Variable Carbon Pile Load Tester
6039
• Test batteries up to 1200 CCA• Fine threaded shaft for fine adjustment• Temperature compensation chart• Easy to read digital voltmeter & ammeter combine with the versatility of a carbon pile load• Spring loaded to shut-off automatically• Unique curved discs to prevent hot spots• Tests all battery types• Made in USA of US and Global Components
-
product
Cathodic Protection Digital Voltmeter
CPV-4
The CPV-4 is a DC digital voltmeter with a input resistance of 20 meg ohm and two voltage ranges
-
product
3 Digit LED Voltmeter
SP 100
The SP 100 is a 3 digit LED voltmeter with 9mm (0.36") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into two 6-way SIL sockets and can be fitted into a panel via the fixing clip. This module is directly compatible with competing products. Splashproof protection to IP65 is achieved by fitting the seal supplied
-
product
4 Digit LCD Voltmeter
DPM 160
The DPM 160 is a 4 digit LCD voltmeter with 12.5mm (0.5") digit height. It features 200mV and 2V d.c. full scale readings, auto-zero, auto-polarity and a set of annunciators. The meter plugs directly into a SIL socket or can be panel mounted using the snap-in bezel and window
-
product
Signal Conditioners
General Purpose
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
product
Miniature AC & DC Voltmeters
PM Series
The PM Series Full-functioned miniature digital voltmeters are AC or DC reading, and feature AC or DC power options, and LED or LCD displays. These versatile meters are available in 100mV, 200mV, 1V, 2V, 10V, 20V, 100V, 200V, or 1000V ranges. Highly accurate (up to 0.02% of full scale), with rapid update rates (up to three reading per second), these meters feature bipolarity (PM-3 is unipolar), a presettable decimal point, overload indication, an extensive list of application-specific options, and easy installation.
-
product
Dual Mobile Communications DC Source w/ DVM
66309D
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66309D dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a half rack box) and eliminates the need for two separate power supplies.The 66309D dc source provides all of the capabilities of the 66309B with the addition of a built in digital voltmeter.
-
product
Voltmeters
ARC Flash No Volts Meter is an ultra-safe portable digital voltmeter. It can provide testing of voltage on firing and related system lines. The 620EXV is certified to meet USA MIL. STD. 810 MTD. 511, therefore compliant for use in explosive atmospheres. This product will accurately inform its operator using red and green lights (which can be set to custom levels) to indicate whether or not the voltage level conforms.
-
product
High Voltage Meter
DU-3900
Delta United Instrument Co., Ltd.
The DU-3900 is a digital voltmeter that can measure high voltages up to a 10kV AC and DC at high accuracy. Its high input impedance (1000M) makes it suitable for measurement of high impedance voltage circuits. Since it has a high accuracy despite its small size and light weight, it can also beeasily used as a portable calibrator.
-
product
Phase Angle Voltmeters
Since the development of the first Phase Angle Voltmeter (PAV) over 50 years ago, North Atlantic Industries has been the industry leader in AC Measurement Instrumentation. Our name has become synonymous with innovation and quality. Our products, specifically designed for defense, industrial, and commercial applications, deliver industry-leading accuracy, repeatability, and reliability.NAI’s units of today are actually multifunction Digital Analyzing Voltmeters that combine a complete Voltmeter, a Phase Angle Voltmeter, and a Waveform Signal Analyzer in a single microprocessor-based instrument. With these versatile and flexible instruments, a wide range of tests can be performed, either manually using the front panel controls or automatically using the IEEE-488 bus. Designed for the Synchro/Resolver and LVDT/RVDT marketplace, NAI’s Voltmeters are used in a variety of applications.
-
product
3 Digit LCD Voltmeter
V 125
The V 125 is a very low cost 3 digit LCD voltmeter with 12.5mm (0.5") digit height, intended for high volume OEM applications. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into a SIL socket or can be panel mounted using the bezel provided. Connection to the meter is via one row of 8 pins
