-
product
IEC61850 Digital Substation Test Tool
PNS630
PNS630 hand-held IEC61850 network analyzer is designed for digital substation commissioning testing and maintenance.
-
product
Cable Identification & Phasing
VCi-3™
The VCi-3™ system is designed for cable and phase identification, mainly for installation or maintenance purposes on three-phase electrical networks during power shutdowns.The transmitter module injects a low current on the cable conductors by direct contact or magnetic clamps methods. A voice message is recorded by the user and will be transmitted along with digital signals. Groundings stay connected at both ends of the three-phase circuit during the test. The detector module is used at the other end of the cable system.
-
product
VHF/UHF Nav/Flight Analyzer
EVSF1000
The R&S®EVSF1000 is a signal level and modulation analyzer for installation in flight inspection aircraft. It performs measurements on ILS, VOR and marker beacon ground stations during startup, maintenance and servicing and analyzes ATC COM signals.
-
product
Coil Analyzers
SAT Series
The Coil Analyzers SAT30A and SAT40A are powerful, lightweight units ideal for testing of circuit breakers. Substation battery is not connected or available. The SAT series instruments are intended to supply circuit breaker coils and spring charging motors. They spring charging motors (SAT40A – AC and DC) as a part of commissioning and maintenance testing.
-
product
Flow Meter
V-Cone
The V-Cone Flow Meter is an advanced differential pressure instrument, which is ideal for use with liquid, steam or gas media in rugged conditions where accuracy, low maintenance and cost are important. With its DP built-in flow conditioning design, the V-Cone is especially useful in tight-fit and retrofit installations in which the long runs of straight pipe required by Orifice Plates, Venturi Tubes, and other technologies are either impractical or unavailable.
-
product
SIMRC - 16-Channel 1-Pole Multiplexer
1020-R-16-1-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
De-Energized Tester
ALL-TEST PRO 34
The ALL-TEST PRO 34™ uses our proven, patented technology to look beyond vibration, temperature, and ultrasound test methods- giving you instant answers on your motor’s health. It represents the 7th generation in product innovation that ensures the reliability of motors in the field and helps to maximize the productivity of maintenance teams everywhere.
-
product
FieldFox Handheld Microwave Analyzer, 9 GHz
N9915B
Keysight's FieldFox portable analyzers are equipped to handle your toughest working environments during routine maintenance, in-depth troubleshooting, and anything in between.
-
product
Software UNIT TESTING product
C-TestIt
Unit testing, in the case of C, is understood as the ability to test a function regardless of the rest of the application.Unit testing is a complement to traditional testing, for those Customers who want to improve the quality of their software and therefore reduce future maintenance costs.
-
product
Pro Battery Monitoring System
iPQMS-Pro
The iPQMS-Pro is a real-time non-intrusive UPS battery monitoring system that measures 48 480 cells. The iPQMS-Pro battery monitoring system provides immediate warnings of battery deterioration which will prolong the life of UPS batteries and reduce battery maintenance and replacement while ensuring uptime.
-
product
Ultrafast Transient Absorption Spectrometer
Harpia-TA
The transient absorption spectrometer HARPIA offers a sleek and compact design together with intuitive user experience and easy day-to-day maintenance meeting the needs of today's scientific world. Adhering to the standards raised by the OPRHEUS line of devices, the entire spectroscopic system is contained in a single monolithic aluminum casing that inherently ensures excellent optical stability and minimal optical path for the interacting beams. HARPIA can be easily integrated with both PHAROS / ORPHEUS and Ti:Sa / TOPAS laser systems. HARPIA features market leading characteristics such as 10-5 resolvable signals along with other unique properties such as the ability to work at high repetition rates (up to 1 MHz) when used with PHAROS / ORPHEUS system. High repetition rate allows measuring transient absorption dynamics while exciting the samples with extremely low pulse energies up to several nanojoules.
-
product
Beverage Analyzer
Orbisphere 6110
The Orbisphere 6110 is the ideal solution for final beverage packages analysis. The unique gas phase technology eliminates the direct contact of the sensing elements with the liquid. This reduces maintenance by eliminating hassles such as bleaching tubing and replacing valves to prevent fouling. The CO2 analysis measurement provides accurate results at any temperature, without having to warm the sample.
-
product
ClicManage
ClicManage is an easy to use and seamless test management solution that improves test productivity by managing requirements, releases, test plans, milestones and defects with reduced maintenance effort. It helps in building a strong foundation for your QA practice by providing visibility to better maneuver testing via one easy-to-use planning, delegating, tracking and reporting hub. Moreover, ClicManage can be interfaced with any third party defect tracking tools along with our proprietary ClicBug.
-
product
IPTV Tester
QuickTest 500 IPTV
The IPTV Test Option for the QuickTest 500 IPTV Tester is ideal for the installation, maintenance and commissioning of IPTV services.
-
product
CAPS Trace-Level NO2 Analyzer
Model T500U
Teledyne Advanced Pollution Instrumentation
The T500U CAPS NO2 Analyzer represents the next generation of criteria pollutant monitoring technology for the direct measurement of Nitrogen Dioxide (NO2) in air. The instrument utilizes a patented Cavity Attenuated Phase Shift (CAPS) technique to provide an extremely sensitive, fast and accurate NO2 measurement in a cost effective and low maintenance instrument package.The T500U provides a direct NO2 measurement, eliminating the need for catalytic conversion or reagents which introduce measurement artifacts inherent in traditional heated metal converter based chemiluminescense instruments. The CAPS measurement approach also reduces maintenance items, and removes the need for hazardous materials and high temperature scrubbers within the instrument. The T500U has an expected maintenance interval of one year under typical ambient monitoring conditions.
-
product
RF Components
Using a Vector Network Analyzer (VNA) for RF component testing for design and manufacturing is based on how the component performs. The analyzer is used in multiple ways from design to manufacturing to tuning, field monitoring and maintenance of antennas, filters, mixers, amplifiers, circulators, isolators, and other RF components. Key considerations component designers should pay attention to when finding an analyzer that fits their needs is a great dynamic range, low trace noise, and fast measurement speed.
-
product
LCD Cable Length Toner & Prope Kit
MT-7071K
The MT-7071K Included 8+1 remote units, let you measures cable length up to 1200M (4000ft), and locate and verify the cable status and troubleshoot wiring. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
product
Power Transformer
We are amongst the leading names in the industry, offering wide range of Power Transformer that are technically advanced in nature and have high strength. Our entire product line is dimensionally accurate in nature and requires low maintenance cost. They are thermostatically balanced in nature AND are easy to install.
-
product
Cable Test Van
ETL-35K
ETL-35K system has a multitude of applications in electrical equipment testing and maintenance: testing cable insulation with DC (rectified) voltage up to 60 kV, measuring small leakage current of surge arrestors, high-voltage testing with AC voltage up to 100 kV at industrial frequency, underground utilities tracing, cable fault pre-location and pinpointing, and measuring capacitance and tan delta of various electrical objects at industrial frequency.
-
product
ARC Fusion Splicer
FBT-19S
Shanghai Fibretool Technology Co.,Ltd.
FBT-19S Optical Fiber Fusion Splicer is small size optical fiber fusions splicer, mainly used for fusion and protection of common communications fibers. The rich functionality and ultra-low splice loss make the splicer adaptive to fiber splicing in various environments. It is featured with small size, light weight, high reliability, greater environmental adaptability, dust-resistant, water-resistant and shock-resistant. Multiple fusion modes and heating modes are available to meet diversified customers’ demands. Fiber loading becomes more convenient and accurate thanks to the ceramic V-groove of high precision, which is easy for clean and maintenance. The splicer is capable of dual-directional fusion. The monitor is a touch screen delivers fresh designed graphical interfaces, which are simple for operation. The modular pluggable lithium-ion battery of large-capacity ensures long-time field operations. The auto environment compensation system greatly improves adaptability of the splicer to hostile environments, so that low-loss splice can be remained consistent in various environments.
-
product
Event Control Module
DR YIELD software & solutions GmbH
The Event Control Module (ECM) allows detection and notification of effects introduced by factory events, such as equipment supply changes, maintenance events or similar.
-
product
Patient Simulators
Patient simulator enables you to complete preventive maintenance testing with one device in less than five minutes, reducing average test time by up to 88 %. The ProSim 8 patient simulator is also ideal for design engineers looking for a known physiological signal output.
-
product
Solar Simulators
Sun 2000 Class A
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house -no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
product
Continuous Emission Monitoring Systems
TML has more than 50 years' experience designing, manufacturing, and supporting continuous emission monitoring systems (CEMS). We have a team of experienced CEMS air quality experts that will thoroughly review your process and operating permit and recommend the most cost effective and reliable solution for monitoring the gases of interest. TML's continuous emission monitoring systems are based on rugged, reliable equipment manufactured to exact standards. The result is products and systems with some of the highest mean time between failure rates in the industry. Whether it's a standard or custom solution, we stand behind our products 110%, guarantee CEMS certification, at least 95% uptime, replacement parts, and 24 x 7 support. We offer a total CEMS solution including data acquisition software for recordkeeping and reporting, lower cost of ownership, superior product reliability and designed for simple and easy maintenance.
-
product
Software Package
System Software 4
BAUR Prüf- und Messtechnik GmbH
The BAUR system software is a cable fault location, cable testing and cable diagnostics package. It enables efficient maintenance of cable networks in combination with BAUR titron systems.
-
product
CMP Mechanical Kits (100x70mm)
230195 – CMP-90-HP
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
-
product
Lithium Battery Equalization Tester
LIFG
Fuzhou Fuguang Electronics Co., Ltd.
The LIFG series Tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem that inconsistent voltage of lithium battery pack. Meanwhile it supports to make the voltage difference of any battery, which can be used for research and development experiments to stimulate what problems will occur when the battery reaches the maximum voltage difference under harsh work working conditions.
-
product
Test Automation Services
Automating software products and applications at ImpactQA is performed with an aim to reduce regression testing time and time-to-market. Ouryears of experience and shining reputation among top automation testing companies have strengthened our engagement with global clients from different industry domains. ImpactQA and its test automation approach involve best in class tools for functional regression automation and webapplication automation testing partnered with creation & maintenance of automated test suites. Our true asset is the availability of IP-driven tools and custom test automation framework that permits cross-platform application testing for both web and mobile applications.
-
product
Integrity Assessment
Accurate and up-to-date insight into the structural integrity of your pipeline gives you a reliable basis for prioritizing maintenance tasks and investments, business planning and mission-critical decisions – helping you optimize costs. Does the pipeline fulfill its functional purpose? Are day-to-day operations being hampered by flaws or anomalies? What is the expected remaining lifetime of the asset?
-
product
pHTestr® 50 Waterproof Pocket pH Tester,
Premium 50 Series
The Oakton pHTestr 50 has a replaceable double junction sensor for longer life, an expanded number of applications, and easy maintenance. Double-junction electrode sensor handles wastewater and solutions containing sulfides, heavy metals, and TRIS. Electrode sensor offers a clog-resistant Kynar® junction and a recessed, glass pH bulb to protect against breakage. Valox sensor housing resists most chemicals. The keypad clicks to confirm operation, and allows access to a variety of functions. Calibrate up to three pH points with the auto-buffer recognition at both USA and NIST standard buffers. Additional features include an automatic temperature compensation (ATC), hold function, auto-off function, self-diagnostic error messages, and a three-segment battery-life indicator.
