Noise Dosimeters
Measure exposure to noise.
-
product
Low Noise Amplifiers
WA Series
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
product
Noise Figure Measurements With Vector Correction
S93029B
The S93029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers, utilizing Keysight’s unique vector-source-correction technique
-
product
Noise Source Family
SNS Series
Works in conjunction with the NFA Series of noise figure analyzers to simplify measurement set-up and improve accuracy and reliability, automatically downloading electronically stored calibration data.
-
product
Active Noise Cancellation
ams analog and digital Active Noise Cancellation (ANC) solutions deliver class leading ambient noise reduction, significantly improving sound quality for portable consumer devices.
-
product
Ultra Low Noise Disciplined Frequency 4220a Standard with Rubidium and OCXO Clean-Up Oscillator
Precise Time and Frequency, Inc.
The ptf 4220A is an Ultra Low Noise Disciplined Frequency Standard with rubidium and OCXO clean-up oscillator.The instrument contains a high performance rubidium module, with an extended life design, and very low aging rate, with high quality OCXO o/p for low phase noise.
-
product
Broadband Coaxial Noise Sources
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
product
Low Noise Amplifiers
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
product
Noise Monitoring Kit
LxT NMS SoundExpert
In addition to the SoundExpert LxT meter, this kit includes the EPS042 protection case and D-cell battery pack, the EPS2116 microphone protection shroud, and EXC010 10 ft. cable. Using D-cell alkaline batteries, allows the noise monitor to be smaller and lighter; avoid the expense of shipping heavy lead acid batteries and the hassle of recharging. You can transport it easily to your site, deploy it, measure data, retrieve your system, download the data, and issue your report.
-
product
Noise & Vibration Tester
System PC Based particularly suitable for vibration and noise measurements for the characterization of mechanical, electromechanical and electroacoustic and for the control and monitoring of installations of production. Complete configurability for the use of platforms PC (Notebook, desktop, PXI) suitable to applications of both static labotatorio, both dynamic (eg road-test) and also in the production line (functional tests and monitoring).
-
product
Pocket IR Dosimeter
Shenzhen Chuangxin Instruments Co., Ltd.
This Pocket IR Dosimeter is a handheld radiometer with the characters of high-precision, pocket, stable property and easy to use
-
product
Noise Source
MNS-1
Matrix Test Equipment Incorporated
The MNS-1 is a shaped noise source that can be used toemulate 2 bands of digital carriers. While it does not havethe necessary attributes to generate a constellation, it doesmimic the loading of QAM carriers. The MNS-2 featuresremotely controllable 6 MHz wide notch filters to allowintroducing a QAM carrier capable of generating a constellationand enabling measurement of Modulation Error Ratio (MER) andBit Error Rate (BER).
-
product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
product
Noise Thermometer
MFFT-1
The MFFT-1 magnetic field fluctuation thermometer is a high accuracy thermometer system for typical dilution refrigerator temperature ranges.
-
product
DBAir Safety Managers Noise Meter System With Octave Bands
06NK103
This Sound Level Meter System with Octave Bands is the ideal system for the professional Health and Safety Manager with occupational noise monitoring duties.
-
product
Durability, Noise & Vibration Test Platform
LMS Test.Lab
Siemens Digital Industries Software
LMS Test.Lab with faster, more accessible and more complete test-based engineering for noise, vibration and durability. From multichannel data acquisition to a full suite of testing, analysis and reporting solutions, LMS Test.Lab 15 provides you with a versatile and rigorous problem-solving toolkit.
-
product
Low Phase Noise Reference Source
96270A
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
-
product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 6 dB)
N4000A
The SNS series N4000A noise source is designed for accurately measuring devices with low noise figure, with a frequency range of 10 MHz to 18 GHz and nominal ENR 6 dB.
-
product
Noise Figure Analyzers & Noise Sources
Keysight Technologies provide a range of noise figure measurements solutions to meet your needs, from the NFA series noise figure analyzers to the noise figure measurement personalities for our spectrum analyzers. We also have a range of noise sources to complete the measurement solution.
-
product
High Frequency Noise Simulator
SKS-H04GA
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
product
Microwave Noise Source Generators
Noise Sources supply white gaussian electronic noise. The output is a flat instantaneous broadband electronic random noise. The noise source converts a DC input to noise. Units are available in bands between 10MHz thru 26.5 Ghz.
-
product
Noise Monitoring
Larson Davis provides complete solutions for noise and vibration measurement and analysis. From stand-alone, simple-to-use instruments to complete systems including sensors, data acquisition, and software, Larson Davis has what you need.
-
product
TriaxM-TriaxM, Low Noise Triaxial to Triaxial Cable for SMUs, 1 m
785659-01
The TriaxM-TriaxM Triaxial Cable connects your system to PXI Source Measure Units and other devices that have a triaxial connector. It uses guarding to remove the effects of leakage current and parasitic capacitance when … measuring very low current signals. The cable offers 300 V DC maximum voltage, 3 A maximum continuous current, 10 A maximum pulsed current, and different lengths.
-
product
Low Noise Accelerometer Cables & Coaxial Sensor Cables
Our cable assembly team in the UK produce the highest quality cable assemblies for use with a wide range of sensing and measurement applications. By making the cable assemblies in our own factory we are able to ensure the quality of every connection and every assembly, each cable is fully tested and its capacitance checked. Due to our experience in signal conditioning we understand the critical elements to quality signal analysis, this includes the correct cable. This is particularly true for accelerometer cables and sensors cables which can introduce significant noise issues if not used correctly.
-
product
Phase Noise Analyzer
NXA-50
This new NXA-50 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 50 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range.
-
product
Mechanical Noise Tuner Control
S93027B
The S93027B enables to control Maury Microwave’s LXI tuner as the impedance tuner and measure the noise figure of unmatched devices (Gamma opt. < 0.9) with the N524xB PNA-X with option 029 and the S93029B noise figure measurement software.
-
product
Noise and Vibration Tester
SKF Condition Monitoring Center
High tech analysis and measurement such as frequency analysis (FFT) and further advanced analysis pinpoints faults. Spectral masks help to optimize the bearing performance in the particular customer application.
-
product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
product
Phase Noise Tester 5MHz to 40GHz
Model 7340
Berkeley Nucleonics Corporation
Broad Frequency Range in a single compact instrument from 5MHz to 40GHz. Measurement offsets from .01Hz to 100MHz. Absolute Phase Noise - High Drift mode (ability to measure modulations, high drifting or unstable DUTs, etc.). AM (Absolute Amplitude Noise) measurements. Pulsed Measurement Capabilities. Transient Mode: measure WB Frequency, NB Frequency, NB Phase, NB Power (WB/NB being Wide Band and Narrow Band). Dual channel low-noise integrated power supplies.
-
product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
