Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXIe Embedded Controller Module
43-920-002
The 43-920-002 PXIe embedded controller is the most compact and powerful 3U one-slot embedded controller for the PXI Express and CPCIexp platforms. With its huge and future-ready interface capabilities, it runs perfectly with most test and measurement applications.
-
product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
product
DataBlaster PCI / PCIE JTAG Boundary-Scan Controller
JT 37x7/PCI
High speed and performance JTAG Boundary-scan PCI PC plug-in controller for PCI bus slot or PCIe PC plug-in controller for PCI Express bus slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
product
Mixed Signal JTAG Tester
JT 5705
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
product
Remote Intelligent Pod
ScanTAP
The test patterns generated by the PCI-1149.1/Turbo controller are distributed to the target system either directly through ScanTAP 4 and ScanTAP-8 pods. The ScanTAP-4 and ScanTAP-8 pods can apply test vectors and/or ISP patterns to target boards with a variety of JTAG chain topologies. In the simplest case, the ScanTAP-4 and ScanTAP-8 will provide the interface between the PCI-1149.1/Turbo controller and a target system consisting of a single JTAG Test Access Port (TAP). This would be the case where the target system consists of one JTAG chain and its single associated TAP.
-
product
JTAG Boundary-Scan Controller
NetUSB-1149.1/SE
8-TAP USB 2.0 and LAN Based JTAG Controller. The NetUSB-1149.1/SE is an advanced 8-TAP USB 2.0 and LAN-based JTAG/boundary-scan controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
JTAG Boundary-Scan Controllers for High-Volume Production Systems
Corelis has designed special hardware that autonomously performs concurrent (gang) testing and programming of multiple units without additional user intervention. The entire testing and programming, including on-the-fly verification of results, is done in modular and expandable hardware.
-
product
USB JTAG controller
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
product
Boundary-Scan Controllers
Boundary-scan test and programming applications are only as dependable as the hardware they run on. JTAG Technologies has the industry’s most reliable IEEE 1149.x high speed and performance JTAG controllers, JTAG interfaces and more. To reliably execute your test and programming applications you can choose from a range of different controllers with different performance capabilities and form factors. For use in design, production and manufacturing and service.
-
product
Boundary-Scan Controller for PXI-Express 'Hybrid' Slots or Plug-In Controller for PXI-Express Peripheral Slot
JT 37×7/PXIE
High speed and performance JTAG Boundary-scan controller for PXI-Express ‘hybrid’ slots or plug-in controller for PXI-Express peripheral slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
-
product
TAP Pods
JTAG Technologies designers have been developing high-speed digital test equipment for well over 30 years. The current range of controllers ranges from the compact, stylish and reliable JT 3705/USB to the rugged, dependable DataBlaster family and variants that have been developed for industrial use. The latest addition, JT5705/USB adds analog measure and source capabilities to provide a true mixed-signal tester platform.
-
product
Embed functional-test
ScanWorks Embedded Diagnostics
The ScanWorks platform for embedded instruments is supported by a wide variety of hardware controllers and accessories with which engineers can connect ScanWorks to their unit under test (UUT). Hardware is available for development, production and repair environments. The test platform required for ScanWorks is either a standard PC or a system with a built-in (embedded) JTAG controller.
-
product
Imbedded A5 Processor Test Interface
Advanced Microtechnology, Inc.
Advanced Microtechnology has extended the application of its Optimum product line with theintegration of ARC5 imbedded test functions. Up to 40 controllers may be independently powered and monitored for functionality using the process test interface of the Optimum WinAOS application. Each part may have 2 separate biases featuring both current and voltage monitoring. Independent test is implemented through a standard JTAG interface. A separate serial clock and command interface may be used if required to provide device initialization sequences. JTAG control is muxed to each part through the use of an independent clock for each part. All of the ARC processor registers and memory space may be tested through the JTAG I/O.
-
product
JTAG Boundary-Scan Controller for PXI and PXI-Express 'Hybrid' Slots or Plug-In Controller for PXI-Express Peripheral Slot
JT 37x7/PXI
High speed and performance JTAG Boundary-scan controller for PXI and PXI-Express ‘hybrid’ slots or plug-in controller for PXI-Express peripheral slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
product
TAP Signal Isolation Module
JT 2139
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
product
ScanBridge
JT 2154
The JT 2154 is an experiment board based on National Semiconductor’s STA111 device, aimed at users looking to utilise addressable bridge/multiplexors within their designs, and thus set-up ‘system level’ JTAG access. The unit can also be used in semi-permanent installations to expand the TAP (Test Access Port) count on JTAG Technologies controllers in order to address highly segmented designs. Built-in support for ScanBridge-type devices within ProVision allows easy set-up of TAP assignments and device addressing.
-
product
Boundary-Scan Test / In-System Programming Controller
CPXI-1149.1/Turbo
The CPXI-1149.1/Turbo is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the CPXI-1149.1/Turbo offers up to 80 MHz clock rates on 4, 8, or 32 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
JTAG Boundary-Scan Controllers
Corelis has developed a wide range of high-performance boundary-scan controllers that are compatible with buses such as USB 2.0, PCI, PCI Express, and Ethernet. Many of Corelis’ boundary-scan controllers operate up to 100 MHz sustained TCK frequency.
-
product
19" Rack Mount Chassis, Industrial JTAG-Powered PCB Tester-Programmer 'CombiSystem'
JT 57××/RMIC
The new-concept, industrial JTAG-powered PCB tester-programmer the JT 57xx/RMIc ‘CombiSystem’ comprises a sleek base-level 19″ rack-mount chassis assembly that can house up to four customer-specified modules chosen from various JTAG (IEEE 1149.x) controllers, digital IO and analog IO and other measurement modules.
-
product
JTAG USB Controller
NetUSB-1149.1/E
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
product
Portable JTAG Boundary-Scan Controller with USB (1.1 and 2.0 High Speed), Ethernet & Firewire Interfaces
JT 37x7/TSI
High speed and performance portable JTAG Boundary-scan controller, containing three interfaces to the test system: USB (1.1 and 2.0 high speed), Ethernet and FirewireThe controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘The JT 37×7 DataBlasters are a family of high speed and performance, up to 40 MHz TCK, boundary-scan controllers. Besides being available as bench-top unit with USB/E-net/FireWire interface, these controllers also come as 19″ rack-mountable instrument with the same three interafces and as plug-in cards in PXI(e)and PCI(e) formats.
-
product
PCI Based JTAG Controller
PCI-1149.1/Turbo
The PCI-1149.1/Turbo is a powerful PCI-based JTAG/boundary-scan controller that is used for testing and in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
JTAG Boundary-Scan Hardware
JTAG Boundary-Scan Hardware by Corelis, including boundary-scan controllers, 12C serial bus protocol analyzers & exercisers, JTAG boundary Scan Modules, high-volume production JTAG systems, 7 support for 3rd party JTAG controllers
-
product
Production Stand-Alone
PSA
Using PSA, test engineers can build sequences of applications in the built-in AEX (Application EXecutive) manager using if then else goto capabilities. Sequence builders can also include additional capabilities through DOS/Win command line calls, create serial number logged test reports, export tests results to a database etc.. PSA includes drivers for all JTAG Technologies controller hardware past or present.
-
product
High-Performance LAN & USB JTAG Controller
NetUSB II™
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires a controller with high performance specifications and diverse features.
-
product
Single-TAP CFM JTAG Controller for Teradyne ICTs
USB-1149.1/CFM
The USB-1149.1/CFM High-Speed single-TAP boundary-scan controller makes adding JTAG test to Teradyne ICTs a snap. Designed specifically for integration into Teradyne TestStation and GR228x testers, the USB-1149.1/CFM offers a clean, convenient boundary-scan solution.
-
product
I/O Modules
JTAG Technologies designers have been developing high-speed digital test equipment for well over 30 years. The current range of controllers ranges from the compact, stylish and reliable JT 3705/USB to the rugged, dependable DataBlaster family and variants that have been developed for industrial use. The latest addition, JT5705/USB adds analog measure and source capabilities to provide a true mixed-signal tester platform.
-
product
4-TAP PXI Express JTAG Controller
PXIe-1149.1/4E
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
product
Transient Suppression for Corelis JTAG Controllers
TAP Protection Adapter
Transient events such as Electrostatic Discharge (ESD), inductive switching, and lightning can damage electrical equipment, leading to costly repairs and test equipment down-time, reducing production capacity and increasing time-to-market.The Corelis TAP Protection Adapter is designed to enhance protection to any Corelis JTAG controller, shielding against harmful events using a combination of electrical defenses.The compact adapter features series resistors and transient voltage suppressor (TVS) diodes to mitigate damage to the JTAG controller. Protect your investment and enjoy peace-of-mind with the TAP Protection Adapter.
-
product
Boundary-Scan Test and In-System
PCIe-1149.1
The Corelis PCIe-1149.1 is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the PCIe-1149.1 offers up to 80 MHz clock rates on 4 or 8 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
High-Speed 4-TAP USB 2.0 JTAG Controller
USB-1149.1/4E
The USB-1149.1/4E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/4E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
