Current Detectors
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-45SH
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
-
Product
Digital Voltage Detector
V-550
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Digital display for detected voltage with beeper sound.Can display AC voltage value by touting the insulation cover of conductor. (Approximate value)Accurate measurements for the bare terminal.Data hold and auto power off function.
-
Product
Non-RMS Responding Power Detectors
-
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
Product
Ultrasonic Flaw Detector
-
Shenzhen Graigar Technology Co.,Ltd.
Flaw detection is the most commonly used technique among all the applications of industrial ultrasonic testing. Generally, sound waves of high frequency are reflected from flaws and generate clear echo patterns.
-
Product
AC Current Sensor
RCTi and RCTi 3ph
-
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
Product
Photo Detector Testing
-
With the rise of 5G technology and popularization mobile devices, more and more advanced photoelectric sensors are used in our daily lives. In order to be better applied to mobile devices, the photosensitive area of these advanced photodetector is getting smaller and smaller. However, these applications place higher and higher requirements on the light sensing performance of advanced photodetectors. In the process of shrinking the photosensitive area, it also brings the challenge of accurate measurement of quantum efficiency. Enlitech adopts the spatial light homogenizing technology and follows the ASTM standard “Irradiance Mode” test method, which is proven that it can accurately perform quantum efficiency and other key parameter measurements of advanced photodetectors.
-
Product
DC Earth Leakage Current Measurement
DCZCT-11M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC Earth Leakage Current Measurement *Bipolar DC ±12V Power Supply*Output DC ±1.5V at DC 10mA *Isolated Housing Case based on UL94V-0*Through Hole PCB Mount Type, Exciting Current Method
-
Product
Ignition Pulse Detector
IP-3000A
-
IP-3000A Ignition pulse detector is a slim and light weighted detector by using amorphous metals fiber element. It is 1/4 in thickness (mass: approx. 1/50) and 1/3 in weight compared with the previous model of Ono Sokki. Also the IP-3000A can obtain constant output from low to high rotation with high sensitivity.Meeting the needs of structure or mechanism in recent gasoline engines, the IP-3000A can easily clamp around an ignition coil cable (the primary side cord of ignition coil or the current cord of electronic distributor). Moreover, heat-resistant design up to maximum operating temperature of +120 C° enables measurement under harsh environment.The IP-3000A Ignition pulse detector can be used with Ono Sokki’s engine tachometer.
-
Product
Current Transducer
IN 1000-S
-
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. 1000 A nominal, 3 ppm linearity over the temp. range, Very low offset drift 19.5 ppm, low noise 34 ppm peak-peak, -40 to +85°C, one compact package.
-
Product
Resistance Tester With Leakage Current (Loop Current)
GT00WD00ZY
-
*screen display*Double protection insulation*Non-contact measured resistance, safe, fast
-
-
Product
In-plant Detectors
-
In-plant detectors are similar in design to the portable detectors. The key difference being, the inspection surface moves past the stationary detectors.
-
Product
Flaw Detector & Thickness Gauge
DFX-8+
-
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Terahertz Generators and Detectors
-
Terahertz generators and detectors are produced and optically prepared at the facilities of Rainbow Photonics in Switzerland.
-
Product
Current Sources
-
Innovar Current Sources are the standard in the circuit breaker industry. Our Current Sources supply regulated current from 1 amp to 100,000 amps with incredible accuracy, along with providing a full set of features that is unmatched by any other Current Source in the market.
-
Product
Flexible AC/DC Current Tester
FCM-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Bending free flexible clamp sensor *Wide measuring ranges (AC/DC 0.001A～2500A)*Easy accessibility to the hard to clamp object*Big CT window (φ200mm)
-
Product
Primary Current Injection Test Sets
-
Our primary current injection test sets cover from 750A through to 6000A. Available in single phase, testing applications include testing and timing of under and over current relays, circuit breakers and CT ratio testing.
-
Product
Voltage, Current and Power Measurement
-
Educated Design & Development, Inc.
For measuring current, especially higher currents and quicker than series ammeters. These units are considered the finest available. All units are extremely rugged, reliable, and versatile.
-
Product
Earth Fault Detector
K-3838
-
Kongter Test & Measurement Co., Limited
Kongter’s K-3838 earth fault detector is the updated model which is developed to fast detect, trace and pinpoint virtual grounding faults on LIVE DC systems where electrical cables have breakage and current lost to ground. It will save you from long time unnecessary troubleshooting and helps to increase the reliability of your electrical equipments. Our unique technique makes it safe and fast to handle earth fault in DC systems that are working online.
-
Product
Carbon Monoxide Detectors for Aviation
AV8 Inspector Collection
-
The Sensorcon AV8 Inspector is a portable, professional-grade Carbon Monoxide monitor designed for aviation enthusiasts and professionals including pilots, ground crew, technicians and inspectors.
-
Product
Current Analyzer Control And Automation App
BV0013B
-
Intuitively control your current analyzer, build automated tests, and log data easily with BenchVue current analyzer software app for deeper current analysis.
-
Product
Current Amplifier/Generator
ULCA-1
-
The Ultrastable Low-noise Current Amplifier ULCA-1 is designed to fulfill the needs of high-accuracy low-current generation and measurements in the range from 1 fA to 1 µA (licensed by PTB).
-
Product
Current logger0 to 20mA
TK-4802
-
Supplied with an input cable, this logger can measure current between 0 and 20mA DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.
-
Product
Brute High Current Probe
P4301-2F
High Current Probe
Current Rating (Amps): 50Current Rating Remark: 40 Amps for BeCu plungersAverage Probe Resistance (mOhm): 5Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,750Overall Length (mm): 44.45
-
Product
Phantom Surface/Web Metal Detector
-
Phantom Surface Web Metal Detection systems are designed to detect metallic fragments in wide, sheeted materials, continuous webs, and other thin products like textiles, paper, boards, food packaging, boxboard, poly films or products packaged on a roll/web.
-
Product
200 Amp AC Current Adaptor
DL6701
-
The DL6701 is a compact 200A AC current clamp adaptor with voltage output via standard 4 mm connectors. To be connected to a digital multimeter or other voltage measurement device.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-110S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
Through Hole Type AC Current Sensor
CTF-600B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A～600A.
-
Product
Planar-Doped Barrier Diode Detector, 0.01 to 50 GHz
8474E
-
The Keysight 8474E is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474E is also very rugged with high resistance to ESD damage. The Keysight 8474E detector is available with a 2.4-mm (0.01 to 50 GHz) connector. This detector offers the options for optimal square-law loads (Option 102) and for positive polarity output (Option 103). Because the unit-to-unit frequency response tracking of this device is typically better than plus or minus 0.3 dB, no matched response option is offered.
