DC Shunts
A resistor which delivers a millivolt of DC output in proportion to the current flowing through the resistor.
-
Product
Switching DC Power Supply
-
Has pure DC output and low ripple and noise, making it an excellent choice for schools, aging testing of rechargeable batteries and electronic products.
-
Product
DC Filter Inductors
-
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
Product
Coaxial Transfer Switch, DC to 50 GHz
87222E
-
Flexibility is essential in signal routing applications, and the Keysight 87222E 4-port coaxial transfer switch offers just that. It provides exceptional repeatability, low insertion loss, and high isolation. These switches provide simplification of design in signal routing and conditioning applications. The Keysight 87222E can be used in a variety of applications such as, a drop-out switch, switching two inputs and two outputs, or signal reversal switching.
-
Product
DC System Power Supply, 12.5 V, 60 A, 750 W
N5743A
Power Supply
The single output, 750W N5743A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current
-
Product
High Performance Autoranging DC Power Module, 50V, 5A, 50W
N6751A
Power Module
The Keysight N6751A is a 50 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Current measurements for small DC motor*Convenient ＋5V single polarity power supply
-
Product
Solar Array Simulator DC Power Supply
62000H-S
-
Chroma Systems Solutions, Inc.
Solar Array Simulator DC Power Supplies by Chroma provide programmable simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000S-H series provides an industry leading power density in a small 3U high package. The Solar Array Simulator is highly stable and has a fast transient response design, which are both advantages to MPPT performance evaluation on PV inverter devices.
-
Product
DC Coupled Current Probe
34134A
High Current Probe
Measure a wide range of applications with this battery-powered, clamp-on probe; use with DMMs or voltmeters
-
Product
Anodizing/Electroplating/Metal Finishing DC Rectifiers
-
CEHCO can supply Anodizing / Electroplating / Metal Finishing DC Rectifiers. We offer standard products and customized solutions.
-
Product
Programmable Step Attenuator, DC to 40 GHz, 0 to 90 dB, 10 dB Steps
84906L
Attenuator
The Keysight 84906L programmable step attenuator offers coaxial measurements to 40 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life greater than 5 million switching cycles per section) and an attenuation range of 0 to 90 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with with only 2.4 dB of loss at 40 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Precision DC Power Module, 20V, 50A, 300W
N6763A
Power Module
The Keysight N6763A is a 300W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB and LXI compliance are standard. Select from more than 30 different DC power modules ranging in capability from basic to high precision, and in power from 20-500 Watts.
-
Product
Programmable Step Attenuator, DC to 26.5 GHz, 0 to 70 dB, 10 dB steps
84907K
Attenuator
The Keysight 84907K programmable step attenuator offers coaxial measurements to 26.5 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 70 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with less than 2 dB of loss at 26.5 GHz. The compact size of the unit, 35 percent smaller than the Keysight 8495/7 26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
SCR CONTROLLED VARIABLE DC POWER SUPPLY
P5085C
-
Shown below is an AC to DC power supply with 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced to a PLC system. These units are customized units, built to order.
-
Product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 8 Prescaler
HMMC-3028
-
The HMMC-3028 is a DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
Product
Bidirectional Programmable DC Power Supply
IT6000C Series
-
The bi-directional programmable DC power supply of IT6000C series combines two devices in one: a power supply (source) and an electronic load (sink) with energy recovery. Based on these two functions, IT6000C offers the functionality of two-quadrant operation. The regenerative capability enables the energy consumed to be put back onto the grid cleanly, saving costs from energy consumption and cooling, while not interfering with the grid.
-
Product
DC Hi-Pot Tester
3010HP, 3025HP & 3050HP
-
The DC Hi-Pot test is an important part and parcel of the electrical safety tests mandated by standards organization world-wide. More than 80 per cent of faults in electrical and electronic systems are due to weak insulation caused by environmental factors such as dirt, grease, temperature stress, humidity, etc that affect the dielectric strength of the insulation material.
-
Product
Digital Lab 30W – 300W Regulated DC Power Supplies
-
- 19” Rack Adaptable – 3U High Digital Output Metering 3 Digit DPM- Constant Voltage/Constant Current Operation- High Stability and Close Regulation ±0.01%- Proven Reliability and Endurance- 3U High- Remote Sensing Facility for 5A & Above Rating Models
-
Product
DC Blocking Power Splitter Combiner
PD5112
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
Product
IP67 DC Blocking L-Band Splitter
PD5131
-
INSTOCK Wireless Components, Inc
PD5131 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5131 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
Product
USB Coaxial Switch, DC to 8 GHz Dual SP6T
U1816A
-
The Keysight U1816A is a switch matrix that consists of two single-pole-six-throw (SP6T) switches. It allows switching of multiple signal paths without physically changing the connections. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. An entire testing process can be automated, increasing the throughput in high-volume production environments.
-
Product
FaithTech FTLP Series 100W/180W Portable Programmable DC Power Supply
FaithTech FTLP Series
-
Shenzhen FaithTech Technology Co., Ltd.
FTLP series is a kind of programmable Portable bench DC power supply, with the widest output range, which allows engineers to test more program requirements with just one device. To be exact, the FTLP series provides full power all the way down to 25% of the rated output voltage. The FTLP series is equipped with RS232 and RS485 as standard interfaces that are essential for system integration, you can also choose USB or LAN interface as your add-on interface. The series supports SCPI and MODBUS-RTU protocol, which is convenient for all kinds of test platform. The FTLP series DC power supply can be widely used in battery chargers, high-voltage ultra-high-speed diodes, electrolytic capacitors, electromechanical control fields, and ATE test systems, etc.
-
Product
Single Phase DC Injection Set Kit
PDC120A/PDC200A
-
PDC120A/PDC200A Single Phase DC current injection set kit is portable test set which could generate DC current for the various testings in railway transportation, HVDC converting stations, etc.
-
Product
DC Electronic Loads
LSG Series
-
*Operating Mode : C.V/C.C/C.R/C.P/C.C +C.V/C.R + C.V/C.P. + C.C.*High Precision, High Resolution (10 A),High Speed Variable Slew Rate (16A/ s).*Sequence Function for High Efficient Load Simulations.*Parallel Connection of Inputs for Higher Capacity. (With 4 Booster Units : Max 9.45kW or 4 Master Units)*External Channel Control/Monitoring via Analog Control Connector.*Program Mode to Create Work Routines for Repetitive Tests.*Multiple-Interface : USB 2.0 Device/Host and GPIB/RS-232C.*Adjustable OPP/OCP/OVP Setting.
-
Product
AdvancedTCA, Type 11A, 5U 19" Horizontal, DC
11A06FJB58Y4HMXX
-
Elma's ATCA, DC, 5U horizontal enclosure with backplane, and shelf mgmt. options. Pluggable and redundant fan trays, PEMs and shelf managers for availability (99.999%). Optimized via backplane signal integrity studies and chassis thermal simulation.
-
Product
SMART Constant Current DC Load Banks
SLB-Series
-
SMART Constant Current DC Load Banks are designed for acceptance testing, discharge testing, battery capacity testing, battery maintenance, engineering examination and other testing for DC power with load. The SMART technology allows a constant current discharge without the need for manual adjustment of current during the discharge test. Our SLB-Series load banks are portable, durable, economic, safe, easy-to-use and come complete with our DataView software, providing the user with a complete data management and analysis program.
-
Product
Power Divider, DC to 26.5 GHz
11636B
-
The Keysight 11636B is a dc to 26.5 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636B power divider/combiner is recommended when making wideband comparison measurements with the Keysight 8757 scalar vector network analyzer.
-
Product
DC Constant Current Source
-
SCR ELEKTRONIKS have developed equipment namely“DC CONSTANT CURRENT SOURCE”. The system comprises of Constant Current Sources having ranges: 900A continues & 3000A short time at 8V maximum.
-
Product
DC current Sensors
CTH
-
The CTH sensors convert dc current to an isolated voltage output, the CTHR sensors convert ac current to a dc output signal proportional to the Arms. All popular process control voltage and current loop outputs are available. Through hole or split core options mean that connection is non-intrusive and straightforward. The available input range of the CTH sensors is any value from 5A to 6000Adc.
-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)
CK058F
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
High-power Programmable DC Laboratory Power Supply (5kW~180kW)
FTP9000 Series
-
Shenzhen FaithTech Technology Co., Ltd.
FTP9000 series DC power supplies provide wider voltage and current output range at full power, this means both low voltage/high current and high voltage/low current devices can be tested using a single power supply. The FTP9000 series offer a high power density, with 15 kW in a 3U chassis. The standalone power ranges from 5 kW to 180 kW, voltage ranges from 80 V to 2250 V, and current up to 6120 A. For ultra-high-power applications, FTP9000 series allow for master-slave parallel up to 10 identical units, maximum output 1.8 MW, with current automatically shared.
