ESD Monitors
-
product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
product
PSCapture Network Monitor and Recorder
PacketStorm Communications, Inc.
Captures network characteristicsEasy-to-use GUIData compatible with emulatorsReal time graphsReal time histogramsUp to sixteen simultaneous capturesData saved & recalled in three formatsHighlight & save capability
-
product
Circuit Breaker Monitoring
Circuit Breaker monitoring for all parameters required to accurately monitor the overall health and performance of circuit breakers
-
product
Wizard Pocket Audio Monitor
AES/EBU
The AES/EBU Wizard is a hand-held digital audio monitor that receives AES/EBU audio at any sampling rate from 32kHz to 96kHz and displays the received sampling rate, lock status, and five different error conditions. It also has a headphone jack with volume control for monitoring digital audio sources.
-
product
Dew Point Monitor
DPM-99
The NFPA99 has mandated that for Med Gas systems the "dew point for locally compressed air shall be monitored and alarmed per 4-3.1.9.8 and 4-3.1.1.2(f) to protect from line pressure dew point rise to 39 degrees F (3.9 degrees C) from a nominal design of 35 degrees F (1.7 degrees C)." This safeguard was the foundation for the new Edgetech Instruments DPM-99 Med Gas Dew Point Monitor. This specifically designed monitor exceeds the requirements set forth by the NFPA and was a collaboration with AIRVAC Technical Services who are certified by P.IP.E as medical gas inspectors in all 50 US States.
-
product
Hydrogen Penetration Monitoring System
MS3112
The Hydrogen Penetration Monitoring System™ provides a method for directly measuring the rate of hydrogen migration through a vessel or pipe wall. This method actually measures the penetration current set up by the hydrogen as it moves through the steel. By sensing and recording this data directly from the pipe wall, this system offers valuable data which can only be indirectly inferred by other methods.
-
product
Power Transformer Monitoring
Optimize the efficiency of your transformers by relying on our flagship DGA monitoring system with long-term stability, no maintenance needs, no false alarms and a revolutionary method for detecting ambient air ingress.
-
product
Monitoring & Simulation
ETAP Power System Monitoring & Simulation (PSMS) is at the heart of the ETAP Real-Time power management system. Power System Monitoring & Simulation is the smart choice for both small and large electrical utility systems, generation plants, industrial sites, manufacturing facilities, and off-shore oil platforms.
-
product
X-Ray Beam Monitors
When standard products just aren’t good enough—or the measurement technology does not yet exist—Sydor Technologies develops technology to enable these complex imaging measurements. Just as we’ve developed next-generation streak cameras and x-ray detectors to meet novel, emerging requirements in national laboratories, we’re doing the same with x-ray beam monitors.
-
product
Health and Usage Monitoring Systems
Honeywell Aerospace Technologies
Health and Usage Monitoring Systems (HUMS) for helicopters provide diagnostic information required for optimum performance. HUMS sensors and embedded diagnostic software monitor and communicate the health and maintenance needs of critical components.
-
product
(Automatic Redundant Battery Selector With Source Control And Monitoring)
ARBS 2600
La Marche Manufacturing Company
Our product is designed with high powered diodes to select the higher voltage of the two isolated DC power sources. The ARBS selects power from the best available battery while isolating the alternate battery bank. The special heat sink diode assembly is manufactured to handle high output requirements with safety margin to spare.
-
product
COMPUTER MONITOR TESTER
MT160
Test a wide variety of PC & Mac computer monitors-all in one unit. Extended scanning formats range from 15.7K to 80 KHz.
-
-
product
In-line Sensor & Auto Range Switching Concentration Monitor
HF-960EM
Measures a wide range of HF concentration from low concentration to undiluted liquid. The HF-960EM achieves high precision measurement by the auto-correction range switching function. Also has the capibility of cleanliness with all PFA sensors. Measurement range: 0 - 50%.
-
product
Condition Monitoring
NEST i4.0
Integrate your condition monitoring hardware and data with NEST i4.0 software.
-
product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-60-10DC
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
product
MOD MONITOR
TYPE HFX-1
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
product
Permanent Monitoring
Real-time Ultrasound and Vibration data indicate changes in healthy function earlier in the P-F Curve than other condition monitoring technologies. Advanced warning allows every maintenance job to be planned while reducing levels of critical spares held in inventory. Reliability teams benefit from a proactive culture that affords them time to eliminate defects rather than simply applying band-aids.
-
-
product
Wireless Soil Monitoring Network
AquaMon
Reduces Water Costs While Maintaining or Improving Crop. Yields Reduces Electrical Costs by Minimizing Pumping Requirements. Reduces ongoing Operating Costs by Eliminating Manual Data Retrieval. Adapts to Multiple Soil Types, Terrain Variations and Micro-climates.
-
product
Free Data Monitoring Software For EZ-Tap™, EZ-Pro™, And Versa-Tap™ Passive Tap Modules
Stratus Engineering's EZ-View™ data monitoring program controls communication and data collection parameters and displays time-tagged communication data and handshaking events in an easy-to-use scrolling display window.
-
product
In-situ Wafer Temperature Monitoring
CI Semi's family of noncontact temperature monitors (the NTM line), offers high end pyrometry products for the measurement of wafer temperatures during process. CI Semi’s flag ship of the line, the NTM Delta, incorporates real-time, same point emissivity measurement and compensation making it the ideal solution for in situ monitoring for processes such as RTP, CVD and PVD. The NTM family is sold to leading tool manufacturers.
-
product
Differential TDR, 35 ps, 15 GHz, ESD, Sxy, OSLT 3.5MM Cal Kit, Aluminum Case, Internal Battery
T3SP15D-B-BUNDLE
Differential TDR,35ps Rise Time, ESD protection,2 phase matched 3.5mm cables,3.5mm Cal. Kit, Battery.
-
product
The Nortech Fiber Optic Monitors
The fiber optic signal conditioners are designed for direct, accurate and real-time temperature monitoring to manage and maximize your transformer’s performance. The Nortech temperature monitor family comes in three different classes: the EasyGrid is the most comprehensive model, the EasyGrid LT is a compact and very cost-effective model for low channel count monitoring applications, and the EasyGrid Base is and even more compact model designed for easy network integration.
-
product
Clamp type AC Current Sensor／for Power Monitor
ZCT-23S
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 0.1A～120A*Current measurements of terminal feeder
-
product
MSR385WD: Data Logger with wireless sensors for operating temperatures up to +125 °C and optional GSM terminal for remote monitoring
MSR385WD
Your product description goes here.
-
product
Noise Monitoring System
Harmony
A system that consists of automatic noise measuring device, transmission device, computer system, and operation analysis software, and provides accurate data necessary for establishing noise-related policiesby providing real-time information such as noise level, location, and device status for each branch.
-
product
Mark II Dual Setpoint Monitor
95006
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
product
Battery Charger-Dischargers & Monitors
It is a compact and multi-functional unit with three major functions: battery charger, battery discharger and battery activator. These three functions could be used individually or comprehensively to facilitate your daily work for battery maintenance. JUNXY single battery regenerator could be applied for different cell voltages, such as 2V, 6V & 12V single cell battery regenerator, while JUNXY battery string regenerator covers 24V, 48V, 110V, 220V battery strings with different charge/discharge current selectable.
-
product
DP Monitor for Compressed Air Systems
Com.Air
The Com.Air dew point monitor has been designed by Edgetech Instruments to offer the highest level of reliability and accuracy available in compressed air system dew point measurement.
