Filter Results By:
Products
Applications
Manufacturers
Fixtures
orient and afix UUT.
See Also: Fixturing, Test Fixtures, Mechanical Fixtures, Vacuum Fixtures, Jigs
- Pickering Interfaces Inc.
product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
Test fixtures
Offers a wide range of standard Test Fixtures that can fit many of your applications and services. From your R & D to your production lines, we have a solution for you.Each products are standard but we can adapt or design your application.
-
product
MECHANICAL TEST FIXTURE KITS
TX-MT-100 SERES
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
-
product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
product
Custom Designed Test Fixtures
We specialize in automated test systems for both RF and digital devices, modules and systems. Please call to discuss your test requirements.
-
product
In-Circuit Test Fixture Design Services
An integral part of board test is the test fixture. Innovations in board technology may manifest themselves as challenges in test fixture design. Utilizing a creative & systematic design philosophy, Acculogic consistently delivers state of the art solutions for the most complex test interface problems.
-
product
Fixtures, Programming & Test Services
Comware Technical Services, Inc.
Fixtures and programming services are available for Agilent, GenRad, and Teradyne testers. Working from CAD data, a program can be created in only a few days allowing for fast and cost effective testing of your products. Engineering services are available for fixture revisions or repairs.
-
product
ICT/FCT-Fixtures Max UUT 370 × 300 mm (wxd)
CK-2 Large (Hold-Down Gate) / 230158
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
product
SHC68-H1X38 High-Speed Digital Flying-Leads Cable Accessory, 1.5m
192681-1R5
76-Pin, Female Flying Leads to 68-Pin, Male VHDCI, Shielded, 50 Ω Digital Cable - The SHC68-H1X38 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments directly to individual header pins for use with a custom breakout fixture. The flying-lead cable has paired signal and ground lines for each channel to preserve signal quality. Each signal and ground line is designed to plug directly into any 0.1 in. header connector. It is a shielded, 50 Ω cable.
-
product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 585 x 250 mm (wxd)
CMK-03
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
GPS/FMS Universal Test Fixture
TA-3000
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
product
High Voltage Tester
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
product
Mobile Optical 3D Measuring System for Online Photogrammetry
PONTOS Live
PONTOS Live is GOM’s tracking system for positioning components, as for a precise alignment on CNC machines or for the adjustment of fixtures. Combined with the GOM Touch Probe, PONTOS Live allows the inspection of areas that are optically difficult to access. Based on the triangulation principle, PONTOS Live analyzes components of different sizes – from a few millimeters up to several meters – point by point and regardless of the material.
-
product
Topside Probing for Functional Test Fixtures
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.
-
product
Shielding Effectiveness
Radiometrics Midwest Corporation
One of the more difficult tests to understand is shielding effectiveness or transfer impedance. The data from these tests may vary dramatically based on the test method selected, test fixture, test setup, measurement sensitivity, test personnel, etc. At Radiometrics all shielding effectiveness test are performed or supervised by NARTE Certified engineers.
-
product
Manual Fixture Kit
230355 – CMK-06
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
-
product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
product
Line Automation Equipment
5000 Series In-line Handler
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 335 x 250 mm (wxd)
CMCSK-02-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 335 x 250 mm (wxd)
CMK-02
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Boundary Scan Compliance Tester
QT900
Qmax Test Technologies Pvt. Ltd.
QT900 Qscan Test system is designed to provide test solution for both Boundary Scan compliance devices and Non Boundary Scan devices. The System provided with Digital IO’s capable of driving and receiving via JTAG IEEE 1149 standard interface and synchronous to JTAG pins. Both Digital and JTAG test are carried out synchronously. Use of virtual test pin and Edge connector eliminates the need of expensive test fixture strategy.
-
product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 450 x 330 mm (wxd)
CMCSK-07-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Manual Fixture Kit
230371 – CMCSK-02-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Tracing-Type Non-Contact Inspection System For LCD/STN/Touch Panel/FPC
TTS
*"Probe + Non-Contact Sensor" enables to delect SHORT after sticking LCD*No Fixture in LCD Inspection*Applicable to FPC Inspection
-
product
Adjustable Press Plate Bed of Nails Testers
Prober Adjustable Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
Test Fixture, Axial And Radial
16047A
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
product
PXI-5651, 3.3 GHz RF Signal Generator
779670-01
3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Test Accessories
By combining the latest in LED technology with the unmatched illuminating dynamics of prismatic glass, this High Bay LED luminaire brings a superior, incomparable proficiency and reliability to the table. With its remote driver capability, the TDK HBLED-540 High Bay LED Light Fixture is ideal for EMC chambers with minimal RF emissions.
-
product
Magnetizer
340B
The Model 300-series magnetizers are designed to handle a variety of magnetizing applications and materials, from small Alnico parts to large blocks of neodymium-iron. Each of these magnetizers feature patented ECS (Electronic Capacitance Switching) technology, which allows the user to change the capacitance of the unit through the front panel. By setting the charging voltage and capacitance of the magnetizer properly, the user can then scale the output energy of the unit to match the magnetizing fixture being used. The 300-series magnetizers also includes a peak current meter, which automatically captures the peak current of the magnetizing pulse once it occurs. A safety circuit internally discharges the capacitor banks if mains power is removed from the magnetizer or if the cabinet is opened during operation. When connected to a suitable magnetizing fixture, the magnetizer is able to disable its front panel controls if the fixture overheats. Other features include a lockout keyswitch and a current sense output jack (this connects to an oscilliscope for viewing of the magnetizing pulse). All 300-series magnetizers can be modified for computer control, photocell trigger, or autocharge operation.
-
product
900 Micron Buffer Fiber Thermal Stripper - TFS-900-250
Shanghai Fibretool Technology Co.,Ltd.
TFS-900 900um buffer thermal stripper design small, lightweight, easy to use and reliable, longitudinal peel, peel force is small, the high quality of stripped fiber; blade durable and easy to replace, using linear bearing guide and thermal stripping to ensure no damage to the fiber, easy to strip coating, stripping speed and other characteristics. With the fixture using the strip dual core optical fiber
