Dynamic Signal
digital processing FFT to reveal properties of a signal.
-
Product
PXI Signal Insertion Switch Module
Switch Module
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
Product
3U VPX Data Recorder Systems For Wideband Signal Collection & Processing
-
*High-Density Channel Configurations Supported*Data Streaming to and from SSD RAID, SBC RAM & GPGPU*Intuitive and Easy to Use GUI*Linux Support*6 TB SSD Storage*DEG’s 3U UltraScale FPGA Carriers*Synchronize Multiple ADC or DAC Channels*0-75c Operating Temperature
-
Product
350 MHz DDS Signal Generator
425A
-
The 425A generates sine, LVDS and LVCMOS outputs simultaneously and is programmable in 10µHz steps from 250kHz to 350MHz and includes an LVCMOS Prescaler and Divider for generating LVCMOS frequencies down to 2 Hz. The 425A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. A Line Voltage AC Adapter is included. SOF8_425 windows software is also included.
-
Product
Dynamic Mechanical Analyzers
-
Dynamic Mechanical Analysis measures the mechanical properties of materials as a function of time, temperature, and frequency. In addition to basic material properties, DMA also quantifies finished part characteristics, reflecting the important contribution that processing has on end-use performance. DMA is commonly used to measure glass transition temperatures and secondary transitions, orientation caused by processing, cold crystallization, cure optimization, filler effects in composites, and much more. DMA provides an accurate measure of material stiffness (modulus) but also other important mechanical properties such as damping, creep, and stress relaxation.
-
Product
Signal , Module, Receiver, QuadraPaddle, iCon Series, 160 Position, for crimp contacts
510160101
Receiver Module
Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
Product
Mixed Signal Oscilloscope
MSOX3104A
Oscilloscope
1 GHz4 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Signal Generator
-
bsw TestSystems & Consulting AG
Especially for signal generation above 50GHz and in waveguide bands is done with a standard lower microwave generator and then the signal is frequency multiplied to get to higher frequencies. The frequency multiplied signal may optionally be filtered to make it spectrally pure and/or amplified to come to an appreciable signal level.
-
Product
Signal Conditioning
-
Mantracourt’s analogue output strain gauge signal conditioning modules offers a flexible solution for any analogue requirement.
-
Product
Signal Conditioners & Interface
-
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
Product
VDI Millimeter-Wave Frequency Extension Modules for PXA, MXA, EXA Signal Analyzers
-
These modules offer low conversion loss and excellent noise figure. Standard features include dual operating modes. First, the module can function as a high performance down-converting mixer. The second operating mode functions as a block down-converter with a broadband IF up to 20 GHz. Power to the module is provided via an included external DC power supply. These frequency extenders minimize conversion loss by multiplying and amplifying the LO signal internally, thus taking advantage of the benefits of low harmonic mixing. This architecture also preserves the X-Series precision frequency resolution and low phase noise, extending those qualities into the millimeter and sub-millimeter bands.
-
Product
MULTI-STANDARD SIGNAL GENERATOR
VENTUS 2.0
-
Ventus 2.0 is a portable multi-standard signal generator operating with USB 2.0. It supports all common terrestrial broadcasting to satellite signals. Changing from one modulation to another is very easy with T-PUMP, included software.
-
Product
Automotive And Signalling Goniophotometers
-
Photometric Solutions International Pty Ltd
PSI offers a diverse range of Automotive and Signalling Goniophotometers. These operate in the CIE A/alpha coordinate system, and are used to measure and evaluate devices such as:
-
Product
Dynamic Contact Resistance Meter
-
Dynamic contact resistance measurements are necessary to understand the condition of the arcing contacts of the circuit breaker. Static contact resistance measurements do not give us information related to erosion of arcing contact, misalignments of the contact, and damages to the driving mechanism.
-
Product
Universal Voltage Signaling PCI Card w/ 5 IP Slots
PCI5IP
-
If you want to use IndustryPack¨ modules with your PCI system then the PCI5IP is the choice for you. The PCI5IP combines features you need with simplicity and speed. Up to 5 IP modules can be installed. 32 bit and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection.
-
Product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts (610138200)
510150131
Receiver Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
Video Signal Generator
MSPG-6100
-
Analog was a main item in display device industries at the past time., but from now on, the digital is getting developed with multi-function and large-sized resolution. MSPG-6100 is basically supporting the Teletext and Closed Caption as multi broadcast for the D-TV(NTSC, PAL), as well as V-Chip (Violence Chip) function to block the violence and sex, etc.. bad program to protect a person under age through the regulation grade.
-
Product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
Digital I/O
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
Dynamic Electric Motor Analyzers
-
Baker's dynamic motor test and monitoring instruments are built to conduct condition monitoring tests of motors and generators from a Motor Control Centre (MCC), or through a Baker EP1000 connection unit. The Baker EXP4000 dynamic motor analyser is a low-voltage, AC- and battery-operated instrument that test motors and generators while they are in operation. The EXP4000 provides health and performance data on the motor, the motor's load, and incoming power to assess motor performance and suitability in context of the entire machine system it supports.
-
Product
20GHz Single Channel Portable MW Signal Generator
LSX2091P
-
The LSX2091P is a 20GHz Single Channel Microwave Signal Generator that offers industry leading performance, in a modern tablet like design that can be used as a benchtop or portable unit. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The portable design with a 10” touch screen offers excellent performance and meet today’s most demanding applications, whether in the lab or out in the field.
-
Product
PXIe High-Speed Digitizer/ Wideband Digital Receiver, 12-bit, 3.2 GS/s, FPGA Signal Processing
M9203A
Digitizer
The Keysight M9203A is a low noise, 12-bit PXIe high-speed digitizer/ wideband digital receiver with programmable on-board processing. With a wide analog bandwidth, this high-speed digitizer is ideal for applications requiring wideband signal capture and very high dynamic range. The M9203A is a dual-slot 3U PXIe 12-bit wideband digital receiver running at 3.2 GS/s, up to 2 GHz instantaneous analog bandwidth and providing a large 4 GB DDR3 acquisition memory. The M9203A features a large XilinxFPGA that can implement different functionalities depending on the selected firmware option. Dedicated functions can also be implemented on board, allowing support of various applications. Furthermore, Keysight is supporting the deployment of custom processing algorithm on this digitizer with the U5340A FPGA development kit. Integrating algorithms minimizes the need for additional circuitry and exploit the full density and speed of the digitizer.
-
Product
Single Channel Signal Conditioner
SAM-3
-
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
Product
Cable Assembly, Twisted Pair, Differential Signals, 78-Pin D-Type Male To Female, 0.5m
A078DMR-078DFR-9A050
Cable Assembly
The A078DMR-078DFR-9A050 is a 78-Pin Male to Female D-Type Cable Assembly with twisted signal pairs suitable for differentialsignals and is designed to be used with Pickering's 40-200 fault insertion switch.
-
Product
High Performance Analog & Mixed Signal Test Solutions
Applicos
-
Effective mixed-signal test solutions demand know-how and experience. Low level analog signals need to be stimulated and analyzed near fast switching digital logic. Cross talk, magnetic fields, clock jitter, ground noise and non-linearity of components, are just a few of the problems that must be addressed. Applicos knows what it takes to design and produce high quality mixed-signal test solutions. They have been servicing the mixed-signal test industry since 1993 and have established a distinguished reputation for providing our customers with high performance, cost effective solutions. In 2018 we acquired Applicos B.V. to extend our portfolio for the ATE business.
-
Product
Signal Conditioning and Filtering
MSXB 067
-
The MSXB 067 Signal Conditioning Expansion Board provides analog signal conditioning for strain gauges, load cells, RTDs, and other resistive sensors. MSXB 067 provides a flexible interface for quarter-bridge, half-bridge, and full-bridge sensors, with two to six wires for each sensor, with or without voltage sense feedback. A small daughterboard supports user-supplied bridge completion resistors.
-
Product
Mixed Signal Oscilloscope - 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX4104A
Oscilloscope
1 GHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
Signal Conditioning
-
Sensors that are used to collect the data from the environment often don’t produce signal of characteristics optimal for an analog to digital converter (ADC) to translate to digital data. Additionally, these signals can be subject to electromagnetic interference (EMI) that introduces noise, having a negative impact on the reliability of the data. To make this analog input readable for the processing unit and dependable enough to give the desired quality of data the signal has to undergo a process of signal conditioning.
-
Product
High-Frequency Signal Amplifier
VCH-605
-
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
Product
Signal Generators
-
Analog Devices signal generators provide an ideal solution for applications such as wireless HDMI®, microwave and millimeterwave radio, and sensor equipment. These products offer a clean signal, broad frequency coverage, and high output power for multiple applications, with competitive functionality and performance against other signal generators in their class. Our technology operates up to the 70 GHz range, and includes bench top and portable options for greater flexibility in design and development.
-
Product
RTM Sensor Signal Conditioning Board
MS 3631I
-
CPCI Rear IO Sensor Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on LAOA, RAOA, AOSS (2), DCM (3), PCS (3), RSA (5) & ASA (4) and TAT sensor interface. This card shall handle excitation, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 4 Analog Plus 16 Digital Channels
MSOX3034T
Oscilloscope
350 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
