Automatic Test Systems
execute test program sets automatically. Also known as: ATS
See Also: Automatic Test Equipment, ATE Integrators
-
product
Imperial Test Executive
ITE
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
product
Wafer-Level Parametric Test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
product
Functional Test
UTS
The UTS functional test system is perfect for electronics manufacturing operations that have a mix of products where operators load and unload devices under test (DUT) and routinely change out fixtures for each type of DUT.
-
product
OLED Lifetime Test System
58131
The 58131 Lifetime Test System is designed specifically for the OLED industry. Model 58131 provides twoquadrant constant current (CC) and constant voltage (CV) stimulus to each OLED panel and acquires electrical and optical characteristics automatically. Two independent and isolated precision source-and-measure units (PMU) are incorporated in one modular card, which is capable of testing two OLED panels. Additional instrument cards are added to expand test capacity. Hot plug and play is a key feature of 58131. When a UUT fails or an instrument card needs to be replaced, 58131 does not have to be shutdown and testing continues for other UUTs. Hot plug and play obviates life test cycle restarts due to isolated faults and significantly improves life test efficiency. We firmly believe that hot plug and play capability should be mandatory for all lifetime test systems.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
Inflight Entertainment System Hardware
Innovative IFEC solutions that enable connectivity, entertainment, and control.
-
product
High Power Programmable DC Power Supply
IT6000D Series
IT6000D, single channel output programmable DC power supply, is applicable in laboratories and automatic test system to provide high-power and stable DC supply. The feature of auto ranging output enables a wide range of voltage and current combinations at full power, unprecedentedly flexible.
-
product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
product
High Throughput Test Platform for Multi-Site & Index Parallel Applications
ETS-88
The ETS-88 is an optimal test platform for testing a wide variety of devices including: simple analog, high precision, high voltage, high current / power, automotive, video, audio, complex mixed-signal, as well as emerging power processes like SiC and GaN.
-
product
6U VPX Direct RF Processing System
VP460
The VP460 is designed to enable customers to begin development of their next generation systems using revolutionary new processor technology. It is in alignment with the SOSA™ Technical Standard to provide the interoperability required by the US Air Force, Army and Navy.
-
product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
product
Mezzanine System Carrier
MMS6245
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
product
NI's Electrical Functional Test Solution
PXI instrumentation ensures complete and accurate test coverage with a modular architecture mounted in ultra-reliable PXI chassis.TestStand and LabVIEW software provide rapid development of complex test steps and sequences. PXI systems conserve floorspace because of their small, light form factor. Order them preassembled and installed using NI ATE Core Configurations.SystemLink™ software deploys updates and democratizes data insights to optimize operational efficiency.
-
product
Computing VITA System
CRS 48.5
The CRS 48.5 is a complete, integrated, pre-tested, ready-to-run HPEC rugged subsystem enabling faster development/deployment at lower cost and risk using the most advanced VITA 48.5 compliant air-flowthrough cooling to allow the integration of up to eight quad core Intel® Core™ i7 processing nodes.
-
product
Dielectric Material Test Fixture
16453A
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
Open Test Platform for High Performance Automotive Applications
TSVP
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
product
EVSE Test Platform
To manage both the challenging high-power requirements of electric vehicle supply equipment and the market demand, it is crucial to rely on a test system that performs to your specs. The right system needs to combine the tools for reliable asset communication, microgrid management, effective protocol simulation and high-power testing. This EVSE platform combines the right energy regeneration equipment with 25+ years of test experience to deliver the results you need to meet conformance in the time you need it.
-
product
Battery Management Systems Testing
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
product
Radio Frequency, Communications, & Navigation Test Systems
Reduce testing time and costs with the Astronics radio test sets for use in military, avionics, and civil security industries.Available in commercial and military grades, these integrated test systems make it easy to develop test program sets and leverage them securely and instantly across all deployed testers at the factory, depot, and operational levels.
-
product
Infotainment Test for Automotive Applications
Multimedia operating interfaces are complex control and display devices for functions such as entertainment, telephony, on-board computers and vehicle settings. The functional test of such complex control units and their networking within the vehicle architecture presents a particular challenge in every phase of the product design process.
-
product
Smart Sensing Systems
The Astronics Smart Aircraft System enables the gathering of information through sensor and IoT technology to help airlines gain the valuable insight needed to increase passenger satisfaction, improve operational efficiency, and lower costs.
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
Design for Testability (DFT Test)
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
product
Test Fixture
N1295A
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
product
High Performance PXI Functional Test System with Mac Panel Interface
TS-5400
The Keysight TS-5400 PXI Series Functional Test System provides automotive, aerospace and defense and industrial control manufacturers with an off-the-shelf PXI hardware and software platform with support for single or multiple DUT test. Designed for testing electronics control modules such as, power train control, complex body electronics and industrial controllers, the TS-5400 PXI Series helps manufacturers achieve higher throughput for their design validation and manufacturing functional test needs with the capacity to empower them to anticipate future functional test needs.
-
product
VPX Processing System
CRS-D4I-3VB1
4-slot, SWaP-reduced, rugged VPX Intel base plate cooled data processing system that can be applied across various applications including civilian and military unmanned vehicles, manned commercial and military aircraft, helicopters, over- and underwater research vessels, ground vehicles, and locomotives.
-
product
Specialty Instruments
Advanced Thermal Solutions, Inc.
ATS offers a variety of unique specialty instruments, designed for specific applications across the electronics industry. These instruments range from providing heat flux measurements and cold plate characterization, to precise isothermal surface temperature control and fan flow characterization.
