PCI Backplanes
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm With SPDT
50-293-113
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
Carrier Board
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
HPx-200 PCI Radar Input Card
-
The HPx-200 is a flexible, cost-effective PCI primary radar acquisition card that captures and processes one or two analogue or digital radar video signals from a single radar. The card is fully supported by SPx software, allowing modern radar processing to be added into legacy systems.
-
Product
PCI Express, Power, USB Cables for Amfeltec Products
-
PCI Express, Power, USB Cables for Amfeltec Products
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB110
-
The FAB110 offers one PCIe x16 slot, one PCIe x4 slots and two 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pi ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB110 is designed for the 6-slot industrial chassis, such as Axiomtek's AX60501 and AX6052.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm - SPST
50-294-114
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Express, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
780575-01
Controller
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
Product
PCI Express Multi-Function Boards
PEX-1002L
-
PCI Express, 32-ch, 12-bit, 110 kS/s Low Gain Multi-function DAQ Board. Includes CA-4002 D-Sub connector
-
Product
3U 6-slots 25Gb Backplane Aligned To SOSA, Apertures For VITA 66/67 Modules
1SVX306AxP-xxxx
-
Designed in alignment SOSA, this 3U backplane offers 6 PIC (Plug in Card) slots supporting high-speed signals on all data paths and VITA 67.3 connectors and VITA 66.5 optical connectors.
-
Product
100MHz, 2 Channel PCI Oscilloscope, Spectrum Analyzer, Transient Recorder, Voltmeter & Abitrary/Function Generator
TP801-AWG-PCI
-
The TP801 AWG is the first PCI card based 100 MS/second measuring instrument that consists of a Voltmeter, Oscilloscope, Spectrum analyzer, Transient Recorder and an AWG (Arbitrary Waveform Generator).
-
Product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
PCI System Timer
SKU-051-01
-
The PCI System Timer uses a hardware clock to synchronize IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.The timer supports variable clock timing intervals. You can configure the clock interval during startup. Currently, the PCI System Timer supports clock interval ranging from 1ms to 64ms.
-
Product
PCI Module
PCI-1553-PLX
-
The PCI-1553-X uses a single UTMC’s Sµmmit or BCRTM communication device as its 1553 bus controller, or remote terminal, or monitor terminal. The single controller has two redundant channels. This controller accesses 64Kx16 word of external memory and has external for both channel A and B. The 3U PCI board has on-board transformers for both channels.
-
Product
PCIe-6353 , PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device
81049-01
Multifunction I/O
PCI Express, 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO Multifunction I/O Device - The PCIe‑6353 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality … leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6353 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI 2 Amp Multiplexer, Quad 16-Channel, 1-Pole
50-635A-008
Multiplexer Module
The 50-635A-008 is a quad 16-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Low Profile, Onboard GBIP Analyzer
780936-01
Signal Analyzer
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
PCI-6289, 32 AI (18-Bit, 625 kS/s), 4 AO (2.8 MS/s), 48 DIO PCI Multifunction I/O Device
779111-01
Multifunction I/O
32 AI (18-Bit, 625 kS/s), 4 AO (2.8 MS/s), 48 DIO PCI Multifunction I/O Device - The PCI‑6289 offers analog I/O, correlated digital I/O, two 32‑bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-1
PXI Express Module
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (1 meter)
-
Product
18-Port PCI Express
PEX 8749
-
The ExpressLane™ PEX 8749 is a 48-lane, 18-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8749 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
Mini PCI Express Interface Card
MPCIE-1553
Interface Card
The MPCIE-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for MIL-STD-1553 networks. Coupled with AltaAPI Represents the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software - in an amazingly small package.
-
Product
PCI-5122, 100 MHz Bandwidth, 100 MS/s, 14-Bit PCI Oscilloscope Device
778758-01
Oscilloscope
100 MHz Bandwidth, 100 MS/s, 14-Bit PCI Oscilloscope Device—The PCI‑5122 high-resolution oscilloscope device has two channels with greater than 75 dBc spurious‑free dynamic range (SFDR) and flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution, low-noise measurements with up to 100 MS/s and 100 MHz of analog bandwidth.
-
Product
PCI Precision Resistor Card 3-Channel, 3Ω To 1.51MΩ
50-297-150
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Cards
-
The PCI bus has been largely overtaken by PCI Express, introduced in 2004. DekTec has been very successful in vending a range of PCI cards, most of which are still available. All functions are now also available on PCI Express, generally with improved specifications.
-
Product
6U Compact PCI Single Board
CP62005
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62005 is a 6U CompactPCI® single board with high-performance, low power consumption and high reliability. It is ideal for ruggedized systems requiring high-bandwidth processing, or for information processing and embedded computing.CP62005 supports 4th generation Intel® Core™ i7 or i5 Haswell processors, up to 16GB onboard DDR3L memory. It also offers 16GB onboard SLC SSD for operating system and drivers. The onboard design of memory and SSD can enhance the anti-shock and vibration performance.CP62005 integrates Intel® HD Graphics 4600 controller, which supports a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA… CRT max resolution is up to 2048x1536. With HDMI/DP/eDP it can be up to 4K. It also supports three independent displays.
-
Product
24-Ch Digital I/O Universal PCI Card
PCI-1737U
-
ISA-Compatible with PCL-72424 TTL digital I/O channelsEmulates mode 0 of 8255 PPIInterrupt handlingOpto-22 compatible 50-pin connectorsOutput status readbackPCI universal card
-
Product
2-slot Fanless Industrial System With Intel® Celeron® Processor J1900, Front-access I/O, PCIe And PCI Slots
IPC922-215-FL
-
The IPC922-215-FL is an energy-efficient fanless 2-slot industrial system with rugged mechanism and optimized expandability. The extreme compact IP30-rated IPC922-215-FL utilizes an onboard Intel® Celeron® quad core processor J1900 2.42GHz with one DDR3L 1333 up to 8 GB memory. To fulfill difference application needs, the rugged Intel® Bay Trail SoC barebone embedded system provides great expansion capability with two flexible PCI/PCIe slots that can be customized. Additionally, the Axiomtek IPC922-215-FL can withstand temperatures ranging from -10°C to 50°C, and is equipped with a wide range 10 ~ 30 VDC power input for industrial application.
-
Product
12-/16-bit 16 Channel DAC for PCI
PCI395
-
The PCI395 features 16 analog voltage outputs, integrated on the factory standard, ANSI certified M-module standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel).
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 395kΩ
50-298-142
Programmable Resistor Modules
The 50-298-142 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω To 472Ω
50-298-020
Programmable Resistor Modules
The 50-298-020 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 1.81kΩ
50-298-122
Programmable Resistor Modules
The 50-298-122 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
