Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
product
20KV 30KV Electrostatic Discharge ESD Simulator
20KV/ 30KV Electrostatic Discharge ESD Simulator
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD-0230/ESD-0220 has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
product
Acceleration Simulation Mode Roller Set for Vehicles with a Single Driven Axle
ASM-BF/1 | VP 230043
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/1 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97.
-
product
Multi-GNSS RF Simulation System
GSS6300M
The Spirent GSS6300M is the ideal platform for entry-level and low-cost test requirements. Capable of generating signals from multiple GNSS coherently, the GSS6300M is a valuable tool in development and production test environments.
-
product
Cell Testing
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
product
PXI Load Resistor Module 40 Ohm to 295 Ohm
40-292-011
The 40-292 module is able to simulate the common short circuit and open circuit conditions that can be experienced in a system due to faulty wiring or sensors. The short circuit position is fully thermally protected and provides a short circuit current limit. The series open switch provides an automatic current limit through the resistor chain and is thermally protected.
-
product
Reference Voltage Measurement Cell
C-80
Cells C-80 and C-100 are used as reference devices for measuring voltage during calibration and adjustment of OLT-series testers.
-
product
Static Constant Loading Tester
Static Constant Loading Tester is mainly used to determine the resistance to the axial static constant load of plastic manhole. A constant force is steadily loaded on the axial direction of the manhole for the specified time, when the test is finished, observing the sample appearance (deformation, collapse, crack or crazing), determine the deformation in axial direction and calculate the deformation ratio of manhole. The machine is also suitable for ring stiffness test, flattening test, ring softness test of thermoplastic pipes.
-
product
ULTRA Test Cells
The ULTRA Series of high performance MEMS handling, stimulus and test cells provides unparalled flexibility and capability for engineering development, characterization or high volume production test of inertial MEMS (accelerometer, gyroscope) semiconductor devices.
-
product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Radar Simulation 3.0
RADSIM
RADSIM provides the fidelity and flexibility of a phototexture-based digital radar landmass simulation (DRLMS) system. It uses Leidos-developed core radar simulation technology and can produce a very high-fidelity geo-specific or generic, simulated real-time synthetic aperture radar (SAR), Doppler beam sharpening (DBS), and real beam imagery to less than one-meter resolution.
-
product
Electronic DC Load, 500V, 16A, 400W
LDH400 Series
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
product
Measurement & Simulation
Highland Technology offers a wide array of tools for measurement, simulation, and control. Tachometers, thermocouples, RTDs, precision voltages, current loops, strain gauges, and more can be measured or simulated by Highland's products.
-
product
Wideband Active Load Pull
S94572B
The software enables power amplifier distortion measurements under varying load conditions that are controlled across the entire modulation bandwidth. When design verification and robustness evaluation require testing the device away from the optimum loading condition, this application provides powerful insight into device performance and degradation.
-
product
Micro Coax, Module, Receiver, iCon, 40 Pos, Fully Loaded
510160129
Micro Coax, Module, Receiver, iCon, 40 Pos, Fully Loaded.
-
product
Coaxial Loads
Loads are supplied standard with N connectors, which are recommended above 500 MHz.
-
product
2 Port T1/E1/PRI ISDN Simulator
SIM-2PRI
The most inexpensive ISDN simulator on the market. This unit has two PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
product
PXI Mixed Configuration Relay Module - 3 Cells Populated
40-138-AA-BB-CC-DD (3 CELL)
The 40-138 2A Relay Module with 3 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
product
Power Frequency Magnetic Field Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Power frequency magnetic field simulator is a special designed instrument with high reliability according to the features of the power frequency magnetic field immunity test for electrical and electronic products.
-
product
Multiphysics Computational Fluid Dynamics (CFD) Simulation & Analysis
STAR-CCM+
Siemens Digital Industries Software
STAR-CCM+ is a stand-alone simulation solution for computational fluid dynamics (CFD), computational solid mechanics (CSM), heat transfer, particle dynamics, reacting flow, electrochemistry, electromagnetics, acoustics and rheology. STAR-CCM+ delivers accurate and efficient simulation technologies through a single integrated user interface and automated workflows. This facilitates the analysis and exploration of complex real-world problems.
-
product
Electric Servomotor Axis Direct Load Torsion Tester
This equipment is a testing machine for the purpose of conducting torque and vibration fatigue / durability test of suspension bush.
-
product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Module For PCI
APXX1553-x
MIL-STD-1553 Test and Simulation Module for PCI with 1, 2 or 4 Dual Redundant channels (APXX1553-1, APXX1553-2, APXX1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APXX1553-x module is the option for the MILScope™ capability. Models APXX1553-1-DS/APXX1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
product
TEM Cells
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
product
High-Performance Application and Security Load Module
PerfectStorm 10/1GE Load Module
Keysight Network Applications and Security
Equipped with powerful multi-core, multi-threaded network processors, PerfectStorm 10/1GbE is designed to satisfy the testing needs of manufacturers needing speed flexibility in their testing resources. Networking equipment manufacturers building new equipment or service providers and large enterprises integrating this them benefit from testing and verifying performance and functionality prior to deployment.
-
product
Radar Threat and Target Simulation Unit
MS 1605
PTG is used to field/LAB evaluation / testing of RADAR. PC is used to control the profile of the target generation. PTG will work in both stand alone and remote mode. The PTG has keypad and LCD for stand-alone operation. The PC can interface the PTG through the USB link. The operator can communicate through the GUI to the PTG. MIL1553B Communication used for Interfacing with RADAR.
-
product
NIBP Simulators
The full-featured SC-5 SimCube® NIBP Simulator provides ECG, Resp, Arrhythmias, Pacer Simulation, IBP, and more for accurate biomedical testing. The SimCube simulates real-life oscillometric pulses by varying both the shape and size of the wave as cuff pressure changes.
-
product
NASA Battery Simulation System
DMC leveraged our established Battery Management System (BMS) Testing Platform to deliver an automated Battery Simulator System to a NASA research group. NASA needed this system to facilitate development of highly specialized battery devices. These battery systems were designed to provide mobile power for advanced electromechanical systems such as Robonaut 2, a dexterous humanoid robot created to perform a wide range of tasks to assist astronauts on the International Space Station.
-
product
Circuit Simulation Software
Proteus Virtual System Modelling (VSM) blends mixed-mode SPICE simulation with world leading fast microcontroller simulation. It enables rapid prototyping of both hardware and firmware designs, in software! Design, Test and Debug your embedded projects in the Proteus electronic circuit simulator before a physical prototype is ordered. Agile development for the embedded systems workflow.
-
product
Ear Simulator
BO1028
The BO1028 Ear Simulator is a special coupler for microspeakers or earbuds that has been designed to be compliant with ATU-T P.57 and IEC 60318-1. While mics in our BP1090 couplers receive sound waves the way they travel through air, the dual compartment chamber of the BO1028 is designed to modify sound pressure so that the mic receives air vibrations the way a human ear drum would receive them.
