Mixed Signal Oscilloscopes
Analyze both digital and analog signals. Also known as: MSO
See Also: Mixed Signal, Mixed Signal ATE, Mixed-Signal Test, Mixed Signal Testers, MIxed Signal Test Systems, MSO
-
product
Signal Generators
Precision Test Systems manufacturers various signal generators. We can also supply other manufacturers or used signal generators. Our main signal generators are listed below.
-
product
Vector Signal Generator
VSG25A
The VSG25A is a 100 MHz to 2.5 GHz vector signal generator, featuring a 12-bit I/Q baseband arbitrary waveform generator which can be clocked at virtually any frequency from 54 kHz to 180 MHz, and includes a 4096×16 bit pattern buffer for built-in or custom modulation.
-
product
SIGNAL & POWER ISOLATOR
EE301-ISOL
The EE301-ISOLATOR will completely isolate your electronic loads inputs & outputs signals plus ground returns from the main power input UUT (unit under test)... The module allows you to control the electronic load just as you would with any standard control signal. Input / Output & Power signals are fully isolated up to 350 VDC.
-
product
Spectrum Monitoring & Signal Intelligence
Modern spectrum monitoring and signal intelligence systems can capture, process, and record wide signal bandwidths at a broad range of frequencies. Engineers need flexible software to adapt these systems to new signal types and threats.
-
product
Video Signal Distributor
MSHM-14UD60
MSHM-14UD60 is a one input, four output distribution amplifer for HDMI signals. It supports resolutions up to 3840x2160/60Hz RGB 444/YCbCr444,422,420 with mixed EDID, HDCP 2.2 and 3D.
-
product
Minimal Signal Noise
SCSI Quiet Cables
Paralan Corporation was one of the first companies to recognize that 90% of the problems with SCSI Bus installations lie with the cables. To address this problem, Paralan developed its own line of high-quality shielded Quiet Cables.
-
product
RF Signal Generators
RF Signal Conditioning provides signal manipulation capabilities for high-frequency or broadband signals. You can use these products to augment the capabilities of connected instruments to improve attributes like accuracy and frequency range.
-
product
Cellular Phone/RF Signal/ Wired Camera/Bug Detector
SH-055GRV / 01125
This Cellular Phone Detector / RF Signal Detector / Wireless Camera Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices
-
product
VXG Vector Signal Generators
Keysight's VXG vector signal generators offer the industry's highest output power with ultra-low phase noise for your most demanding wireless and aerospace and defense applications. With the VXG's multichannel architecture, quickly switch from blocker and interferer tests to MIMO and beamforming tests.
-
product
Oscilloscope 50 GHz, 4 Channels
UXR0504B
UXR0504B Infiniium UXR-Series is the 50 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope.
-
product
Portable Measuring Complex - Analog Signal Analyzer
The system is designed to collect data during model tests in a pilot pool.The complex is built on the basis of a laptop in a protected design, a National Instrumrnts data collection board and two external connector blocks with BNC connectors, allowing you to connect up to 32 analog signals.
-
product
Oscilloscopes / Digitizers
High input voltage range up to 500 VppIsolated versions with 1 or 2 channelsIntegrated timer/counter & DVM functionHigh input impedance up to 1 MΩ || <20pFAnalog and digital trigger functions
-
product
Signal Analysis
Modal Analysis
Modal Analysis is used for analyzing pulse and transition characteristics of signals coming from the input channels of FFT spectrum analyzers and seismic stations in real time or recorded time realization view mode.
-
product
PCI-5152, 300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
779945-01
300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device—The PCI‑5152 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations.
-
product
Signal Splitter
The Dynamic Signal Buffered Splitter protects sound and vibration sensor acquisitions from the unwanted effects of a parallel troubleshooting or diagnostic instruments. G Systems Dynamic Signal Buffered Splitter provides buffered and unbuffered outputs connected to the same signal input. Up to 16 sensors, typically accelerometers, proximity probes, microphones, and pressure transducers, may be connected to the 16 signal inputs.
-
product
Load Cell DIN Rail Signal Amplifier
LCD20
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
product
Digital Oscilloscope
MOSTs5
MOSTS5 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values, measure time intervals between two instantaneous voltage values through two independent galvanic isolation channels.MOSC5, according to the conditions of use, meets the requirements for measuring instruments of group 3 in accordance with GOST 22261-94.
-
product
Signal, Contact, Receiver, TriPaddle, 5 Amp, .025" Round Post
610110179
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
product
500 / 1000 / 1500MHz Synthesized Signal Generator
Model 2100 Series
- Combine with DDS and PLL Techniques- 1500MHz Maximum Frequency- 1 ppm High Accuracy, Less Distortion- Dual Independent Outputs- AM, FM, FSK, PSK Modulation
-
product
WaveSurfer 3000z Oscilloscopes
WaveSurfer 3000z Series
The WaveSurfer 3000z has a 10.1" capacitive touch display, the longest memory, and the deepest toolbox – all at an affordable price.
-
product
Signal Conditioners
General Purpose
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
product
PC BASED OSCILLOSCOPE
IBL-2100
International Biological Laboratories
PC BASED OSCILLOSCOPE (IBL-2100)
-
product
Signal Finder
Digital satellite finder, Digital satellite meter, HD DVB-S/S2, Demodulation QPSK, 8PSK, Display POWER、C/N、Quality value, Upgrade software & parameters through USB2.0 Port, Easy to read LCD.
-
product
Signal Acquisition
277
The Model 277 is designed around the Texas Instruments ADS42LB69 16-bit ADC. The 250 MHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
product
RETURN PATH SIGNAL GENERATOR
TG-1215
Circuit Method : Individual or Simultaneously. Frequency : 20/30/40/50/60MHz(5carriers). LOW BATTERY CONSUMPTION. COMPACT SIZE DESIGN. OUTPUT LEVEL ADJUSTABLE. OUTPUT LEVEL DISPLAY. MAX. 5CARRIES(individual or Simultaneously). PORTABLE TYPE(weight less than 500g). APPLICATIONS: Testing and aligning CATV return band. Testing and adjusting Internet return band.
-
product
Dynamic Signal Analyzer & Data Recorder
Spider-20
The Spider-20 series of products are compact yet powerful data acquisition and dynamic measurement systems. These units provide four 24-bit precise high-fidelity input channels, and a unique software-selectable tachometer-input/signal-source output channel.
-
product
Oscilloscopes
Various models of digital oscilloscopes for training, laboratories, technical support or certification centres.
-
product
Dual-channel Digital Oscilloscope
ScopeDAQ 12
Dual-channel digital oscilloscope ScopeDAQ 12 allows the user to capture the data with frequency 50MHz. Higher sampling frequency (100MHz) is available in case of using one channel. Basic version of the instrument is equipped with 128K data buffer, optionally it can be enlarged up to 512KB.
-
product
Signal Conditioning System
SCS-801
The SCS-800 is a high-performance signal conditioning system for PC-based data acquisition. An SCS-800 system consists of an AC operable chassis and up to 8 multi-channel modules.The SCS-800 takes advantage of the increasing capabilities of notebook and desktop PCs by leveraging off the PC's strengths. It provides a high-performance, flexible solution whether used as a conditioning front-end for desktop systems in the factory or as a mobile solution for portable systems in the field.
-
product
Opto-Isolated Current Loop Signal
4029
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
