SD Card
A non-volatile memory card format.
-
product
PCI Multiplexer Cards
*High-density 4-bank, 24-channel, 2-pole multiplexers*2 Amp multiplexer range with 18 configurations between single 64-channel 1-pole and quad 8-channel 2-pole*High-density multiplexers with switching formats between 5-channel, 32-pole and 198-channel, 1-pole*High-voltage multiplexers designed for cable testing applications*Supported our eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures our switch systems.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm - SPST
40-294-133
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI 39xSPST 2Amp Relay Card
50-132-003
The 50-132-003 39xSPST relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
product
VITA 57.4 FMC+ HSPC Loopback Card
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
product
Analog-to-Digital Converter (A/D) and Counter-Timer Card
AD8-16 (ADA-8)
Model AD8-16 (alternate part number ADA-8) is an economical, multiplexed, eight-bit Analog-to-Digital Converter (A/D) and Counter-Timer card for ISA-bus computers. It accepts up to eight differential or 16 single-ended analog inputs (jumper configured). AD8-16 requires a full-size expansion slot. All connections are made through a standard 50-pin connector. Base I/O address selection is via dip switch.Analog inputs are multiplexed, amplified, held by a sample and hold amplifier, and then digitized by an eight-bit A/D converter. Amplifier gain is selected by software and can differ from channel to channel.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 131k Ohm
40-294-034
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Multifunction ISA DAQ Cards
Multifunction cards provides analog input, analog output, digital input, digital output, and counter/timers for signal measurement.
-
product
VPX GPGPU Processor Card
VPX6-4942
Curtiss-Wright Defense Solutions
The rugged VPX3-4942 NVIDIA Tesla Maxwell-2 GPU processor is designed and manufactured by Wolf Advanced Technology. The board is part of a family of GPGPU modules available from Curtiss-Wright Defense Solutions to enable development of High Performance Embedded Computing (HPEC) systems.
-
product
PCIe to 3U VPX Extender / Riser Card
This adapter can be used to run, test or program a 3U VPX card in a standard PC PCIe slot. SSC switchable (ON/OFF) PCs available from PCI-Systems Inc.
-
product
PCI 16xSPDT 2Amp Relay Card
50-131-001
The 50-131-001 16xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm
50-293-033
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 8-Slot BRIC 192x8 Matrix, 2A 2-Pole (8 sub cards)
40-565A-102-192X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm - SPST
40-294-124
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI 4-Slot BRIC 24x8 Matrix, 2A 2-Pole (1 sub card)
40-565A-002-24X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
FPGA Mezzanine Card
FMC216
The FMC216 is a 16-channel DAC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. It provides 16 D/A 16-bit 312.5Msps (2.5Gsps with x8 interpolation) channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
product
GPIB Controller Card
GPIB-cPCI-XL
The GPIB-cPCI-XL is a GPIB controller card for PXI and CompactPCI computers.
-
product
Systems Integration for Circuit Card Assembly
Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required
-
product
PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm
50-296A-121-9/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
ARINC825 Cards
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5050
The GX5050 is a high speed Dynamic Digital I/O card that provides a full set of features that is comparable to high speed I/O products found in large functional test systems. The card shares an identical architecture with the GC5050, but the GX5050 is a PXI card (6U) and the GC5050 is a PCI card. Both have the ability to operate independently of the host computer when in RUN mode.
-
product
Single Slot Intelligent Interface Card
IIB-3910-PC/AT
The IIB-3910-PC/AT is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for PC compatible host systems
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm
50-294-012
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Ethernet FPGA Mezzanine Card
Sundance Multiprocessor Technology Ltd.
Quad Gigabit Ethernet FPGA Mezzanine Card that can be integrated with the EMC2.
-
product
Fanless Embedded System With Intel® Core™ I5-7300U/i3-7100U & Celeron® 3965U, 2 HDMI, 2 GbE LAN, 4 USB 3.0 And PCI Express Mini Card Slot
eBOX560-512-FL
The eBOX560-512-FL is powered by the Intel® Core™ i5-7300U/i3-7100U or Celeron® 3965U processor. To enhance system efficiency, the embedded box PC supports one 260-pin DDR4-2133 SO-DIMM socket with up to 16 GB system memory. Two HDMI ports with up to 4K resolution are supported for dual independent display applications. The palm-sized fanless embedded system is dedicated to smart factory automation, thin clients, industrial controller system, digital signage and retail equipment. Axiomtek's eBOX560-512-FL was designed to operate reliably in industrial and embedded application environments. It is enclosed in IP40-rated heavy-duty aluminum extrusion and steel enclosure and offers a wide operating temperature range from -10°C ~ +50°C (+14°F ~ +122°F) and up to 3G vibration endurance.
-
product
PMC Card
P-DIS
The P-DIS PMC card is different from most currently available data acquisition boards. It provides multiple I/O types on a single module and the functionality to work with high-speed digital I/O signaling. With very accurate time stamping of input data and synchronization to an external IRIG-B source, the P-DIS provides the capability to precisely synchronize all output ports.
-
product
PICMG 1.3 Half-size CPU Card With Intel® Celeron® Processor J1900 (up To 2.42 GHz), SATA2, CFast™, VGA/LVDS And Dual LANs
SHB215
*Intel® Celeron® Processor J1900 up to 2.42 GHz*1 DDR3L-1333/1600 SO-DIMM, up to 8GB*VGA and LVDS with dual-view supported*1 CFast™ socket onboard
-
product
High Flexibility Test Controller Card
TCC 1800-UE
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
product
500 MHz RF Multiplexer Plug-In Card
1260-150
The Astronics 1260-150 is an RF multiplexer plug-in relay card for the Adapt-a-Switch™ carrier. It quickly and easily plugs into the front of the Astronics 1260-100 and 1260-101 Adapt-a-Switch™ VXIbus Carriers or Astronics 1256 GPIB/Ethernet and 1256L (LXI Core 2011 Compliant) switching mainframes.
-
product
3U VPX Processor Card
VPX3-1260
Curtiss-Wright Defense Solutions
Optimal for high performance embedded computing (HPEC), general processing, and a variety of C5ISR applications, the VPX3-1260 rugged single board computer (SBC) delivers a fully-featured, all-in-one processing solution for your embedded system.
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 350 Ohm
50-265-012
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
