Leakage Current
-
product
DC Hipot Test Set
KVZG
KV Hipot Power Test Equipment Co.,Ltd
DC Hipot Tester is applied to measure output voltage and leakage current for zinc oxide arresters, magnetic blowing arresters, power cables, generators, transformers, circuit breakers and other equipment.
-
product
AC / DC Combined High Voltage Test Set
Cambridge Instruments & Engineering Co.
suitable to perform AC High Voltage Power Frequency test on transformers, motors, cables etc. Leakage current can be measured at desired pressure and this set can be used as a source for cable fault burning.
-
product
Low CxR
Is a low output capacitance solid state relay containing a GaAs LED on the light emitting side (input side) and MOS FETs on the output side. A small flat-lead package has been provided which realizes a reduction in mounting area of about 50% compared withthe PS78xx series. It is suitable for high-frequency signal control, due to its low C × R, low output capacitance, and low off-state leakage current.
-
product
Leakage Current Tester
2675
Shenzhen Chuangxin Instruments Co., Ltd.
RK2675 series Leakage Current Tester is used to measure the electrical insulation quality and products’ safety performance of the main indicators.
-
product
Safety Test Panel for Water Cooler
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of washing machines. In addition to the conventional safety tests, test for performance is also included.
-
product
Relays
PhotoMOS®
Panasonic Industrial Devices Sales Company of America
Panasonic PhotoMOS® Relays are MOSFET-enabled Solid State Relays featuring low off-state leakage current and stable on-resistance over the component lifetime. Low CxR values, high optical isolation between input and output, and DC and AC / DC load ratings. MOSFET drivers available in SSOP, SOP 4-pin, and DIP 6-pin.
-
product
High Voltage, Continuity & Hipot, Cable & Wire Harness Test Systems
CableEye HVX, HVX-21
Fast ● Simple ● Precise
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections
HVX (Item 829) 1500 Vdc, 1000 Vac
HVX-21 (Item 829A) 2100 Vdc, 1200 Vac
For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV).
All CableEye testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components).
Standard Features & Benefits:- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
product
DC Hipot and Megohmmeter
PTS Series
The PTS Series can perform high voltage DC hipot/proof and current leakage testing as well as resistance measurement testing. Most models offer a high output current for quicker charging of capacitive loads like cables. Like all HVI portable test equipment, the PTS Series is designed to withstand the rigors of field use.
-
product
Cable & Insulation Testers
A cable insulation resistance test is a test that is performed by applying 500 V or more between the conductor and ground and measuring the resulting leakage current. An insulation resistance tester is a test instrument that measures current that leaks through the insulation into ground. Insulation resistance tests can be performed with insulation multi- meters (IMMs) or megohmmeters. Insulation resistance testers are calibrated to display megohms (MΩ) of resistance. A satisfactory insulation resistance measurement should be in millions of ohms.
-
product
Digital Earth Resistance Testers
ST-1520
Capable of measuring earth voltage.2mA measuring current permits the testing of earth resistance without tripping earth leakage current circuit breakers in the circuit.Auto power off function.The timer operates automatically for approximately three to five minutes when the "push button switch" and "timer on button" are pressed together.
-
product
Capacitors - MNOS Series
Macom Technology Solutions Holdings Inc.
MACOM’s MIS capacitors utilize a silicon nitride dielectric over a thermally grown silicon dioxide base. The resultant composite dielectric exhibits low leakage current and insertion loss with excellent long-term stability. The temperature coefficient of capacitance is typically +55 ppm / ºC and is ideally suited for high reliability applications.
-
product
Namur Inductive Proximity Sensor
Shanghai Pubang Sensor Co.,Ltd.
1. NAMUR SENSOR, super low leakage current design2. Eliminate the security risks3. Suitable for inflammable and explosive dangerous areas
-
product
Iron Core Earth Tester
Weshine Electric Manufacturing Co., Ltd
Transformer iron core grounding current tester is a high-precision clamp meter specially designed for measuring AC leakage current, current and voltage. Large diameter (80×80mm) can clamp φ80mm cable, or 96mm×4mm flat steel ground wire, suitable for cables Leakage detection and transformer grounding flat steel leakage measurement.
-
product
SPD AC & DC Thermal Stability Test Equipment
Shanghai Guantu Technology Co., Ltd.
1. Computer control measurement, PLC control;2. Equipped with sudden voltage capability, suitable for thermal stability tripping test under high current conditions;3. Increase the high-power resistance box;4. The interface is friendly and beautiful, and can reflect the running status of the system in real time; .5. Automatically draw voltage, current and temperature curves;6. The system performs multi-point temperature detection in real time;7. Timing sampling and recording function, which is convenient for users to view temperature values at different times and compare data;8.2 times Uc leakage current test function to check the tripping reliability of the product;9. Built-in test box;10. RS232 communication interface, can realize remote control.
-
product
Analog Hipot & Insulation Tester
KT-5000Pi
This is a Hipot(Puncture) Tester combined with Insulation Tester in a set.It tests 2 kinds of test continuously in sequence, and any of both hipot or insulation test can be set to test first in other by the selection switch.Hipot Tester has the leakage current meter, so the operator can check the leakage value while testing. And the preset procedure of the Insulation Tester is very easy. Both tester judge the product to be good or bad automatically in a short time.This tester has many I/O ports to connect extra test system. Price : 2,550 (USD)
-
product
High Speed Response, High Accuracy DC Leakage Current Sensor
DCZCT-20CDHL
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Low DC current measurements.*DC1mA～200mA*High accuracy.*±1%F.S ±10mV*Least influence of magnetization.*Less than DC1mA in current level*Convenient +5V single polarity power supply.*Reference voltage (Vref) terminal is equipped.
-
product
Cable Test Van
ETL-35K
ETL-35K system has a multitude of applications in electrical equipment testing and maintenance: testing cable insulation with DC (rectified) voltage up to 60 kV, measuring small leakage current of surge arrestors, high-voltage testing with AC voltage up to 100 kV at industrial frequency, underground utilities tracing, cable fault pre-location and pinpointing, and measuring capacitance and tan delta of various electrical objects at industrial frequency.
-
product
Medical Electrical Safety Testers
Shanghai Beha Electronics Co., Ltd.
Special purpose AC milliammeter designed to measure hazardous leakage current from electrical appliances and other power line operated equipment.
-
product
Safety Compliance Test System
EN 60601
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-22F
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for leakage current measurements*Ultra compact size*AC 1mA～100A
-
product
Benchtop DC Hipot Testers
DBT Series
DBT Series benchtop models are ideal for testing medium and high voltage electrical components and apparatus requiring DC withstand testing or a DC current leakage measurement (hipot test). These products are housed in benchtop cabinets for industrial and commercial markets.
-
product
TriaxM-TriaxM, Low Noise Triaxial to Triaxial Cable for SMUs, 3 m
785659-03
The TriaxM-TriaxM Triaxial Cable connects your system to PXI Source Measure Units and other devices that have a triaxial connector. It uses guarding to remove the effects of leakage current and parasitic capacitance when … measuring very low current signals. The cable offers 300 V DC maximum voltage, 3 A maximum continuous current, 10 A maximum pulsed current, and different lengths.
-
product
3W to 10W - Single Output / Multiple Output
PXC-M Series
*Industry Standard DIP-24 Package*9-36 Vdc, 18-75 Vdc Inputs*3.3, 5, 12, 15, 24, ±5, ±12, ±15 Vdc Outputs*5 kVAC Isolation (2 x MOPP)*IEC/EN60601-1, ES60601-1, CE Mark*Low Off-Load Power Draw*2.5µA Leakage Current
-
product
AC Leakage Current Tester
229-2
Testing for dangerous small leakage currents is easy with the Simpson Model 229-2 Leakage Current Tester. For use in appliance field service, in the lab, or in production, the 229-2 approximates the human threshold of perception in detecting hazardous AC leakage current. The 229-2 comes with test leads with alligator clips, manual and batteries.
-
product
Electrical Safety Analyzer
19032
Chroma Systems Solutions, Inc.
Our Electrical Safety Analyzers combine Hipot, Insulation Resistance ( IR), Ground Bond (GB), Leakage Current (LC)/AC LC/DC LC, and Dynamic Function Tests. Savings can be up to 50% of production line space by not having to purchase and rack several safety test instruments. It also increases efficiencies of electrical safety testing and reduces associated labor costs.
-
product
Multimeter Clamps
The ideal tool for detecting and measuring the leakage currents flowing to earth.The versatile clamp also offers all the functions of a multimeter clamp.In addition, the clamp is equipped with an RMS converter to ensure that the measurements remain accurate even in the presence of distorted signals.
-
product
Low-Voltage Arrester Analyzer
Weshine Electric Manufacturing Co., Ltd
1. This instrument can be widely used in equipment maintenance of substations and power plants, and to measure insulation resistance, absorption ratio and polarization index of high-voltage electrical equipment such as transformers, reactors, capacitors, and circuit breakers. The leakage current of the low-voltage arrester of the power distribution cabinet is automatically tested.
-
product
Cost-Effective ATE System
PRO RACK ATE
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
product
High Impedance Active Probes
18C & 19C
High impedance probes, PICOPROBE® MODEL 18C and MODEL 19C, combine the most advanced MOS and bipolar technologies with special, low capacitance packaging techniques to achieve truly remarkable electronic measurement capabilities. While being manufactured each instrument is individually optimized for the best possible performance. The extremely low input capacitance, high input impedance, and almost negligible input leakage current permits the direct probing of even the most sensitive MOS dynamic nodes. At the same time, the full dc capability of this Picoprobe coupled with the high speed capability permits the full characterization of circuits.
-
product
Multi-Operational Surge Tester
MB Model
Bench all-in-one versatile Multi-Operational Surge Tester that you need for all of your electrical insulation testing. The Hi-Pot tester has separate L.E.D. panel meters for direct readout (voltage and leakage current) so that no interpolation on the scopes display is ever needed. This MOST can surge test extremely low inductance windings, DC armatures, etc.
