Filter Results By:
Products
Applications
Manufacturers
Fiber Optic
Field of optic fiber application.
See Also: Fiber, Fibre, Fiber Optic Test, Reference Transmitters
-
product
Small Aperture Fiber-Optic Probes
Small-aperture Fiber-optic Probes are best for testing closely-spaced LEDs. With an aperture of 1mm, and a diameter of 1.2mm/0.050 inches, they can test LEDs spaced as close as 0.050 inches on center. Small-aperture Fiber-optic Probes are available with straight or right-angle stainless-steel tips as shown below. This allows for precise customization to your mechanical constraints.
-
product
Fiber Optic Multimeter
Combines the function of fiber optic power meter and fiber optic light source and the user can easily switch to choose the multi meter function via the control menu.
-
product
Fiber Optic Transceivers
Shanghai Tarluz Telecom Tech Co., LTD
Also known as Optical Transceiver or Optical Module. It is a small packaged device that uses fiber optic technology to transmit and receive data.
-
product
Fiber Optic Modem
VCH-608
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
product
Fiber Optic Inspection Microscope
80760
The Miller 200x Microscope helps inspect fiber optic connectors quickly and easily. Its ergonomic design and built-in features make it ideal for field and lab use. The microscope features a pressure-activated on/off switch, focusing wheel, eyepiece, auxiliary white LED light source rated for 100,000 hours, adapter tip for inserting ferrule and battery compartment.
-
product
Fiber Optic Strain Sensors
Opsens Solutions optical strain sensor delivers reliable results in harsh environment. Opsens Solutions OSP-A fiber optic strain transducers are designed to provide accurate deformation measurement in the most adverse conditions. Its small size and EMI/RFI electromagnetic environment and lightning immunity makes it the ideal sensor for geotechnical, structural health monitoring, Defense and aerospace and general applications.
-
product
Fiber Optic Light Souces
Optical Wavelength Laboratories
7-segment LED wavelength displayMultimode and singlemode readyDual-wavelength ports allow automatic wavelength switchingTest two wavelengths at a timeSC connectors (ST and FC available upon request)Bundle with Fiber OWL 7 optical power meters for automatic dual-wavelength Tier 1 certification
-
product
Fiber Optic Connectors & Cages
Pulse Electronics Networking BU supplies high-quality fiber optic connectors and cages to innovative ODMs, OEMs and other manufacturers designing today’s most demanding network products. Our line of 40+ fiber optic connectors include SFP, SFP+, and QSFP connector and cage products.
-
product
CATV 1310nm Fiber Optic Transmitter
MX862T series
The MX862T series direct modulated transmitter delivers high performance signal transmission of NTSC, PAL, digital or compressed digital information for CATV and/or telephony applications.
-
product
Omicron Fiber Optic Connector
Teledyne Impulse-PDM’s Omicron 5030/5070 optical connectors utilize proven small form factor ferrule technology and are available for multi-mode or single-mode operation.The connectors are offered, as standard, in stainless steel to BSEN10088-3 Grade 1.4404 (316L), which is electro-polished to remove surface contamination, thus improving resistance to corrosion. Connector bodies can also be manufactured in other materials, either to address specific anti-corrosion requirements, or to increase depth rating. Engaging nuts are normally manufactured in naval brass to UNS C46400.
-
product
Fiber Optic Cable Assemblies
Amphenol Fiber Systems International
For applications demanding reliability, traceability and the highest level of quality, a complete plug-and-play cable assembly directly from the manufacturer offers the highest degree of confidence. For these most demanding applications, AFSI specializes in manufacturing custom cable assemblies with quality components and industry-leading workmanship. AFSI is able to assist in designing and producing custom cable assemblies from a set of requirements or building to a customer print. Our highly skilled technicians are trained to a wide variety of industry standard procedures critical to manufacturing harsh environment fiber optic cable assemblies. All AFSI cable assemblies are manufactured by expert technicians in our state-of-the-art, AS9100 certified facility.
-
product
Fiber-Optic Probes
Once your Universal Light Probe Sensor has been selected best for your test, the two-part solution is completed by selecting the suitable Fiber Optic Probe which is best for your application.Fiber Optic Probes come in a variety of different aperture sizes, lengths and cable types to suit your application.
-
product
Fiber Optic Test Solution
Eye-BERT Micro 10G
The Eye-BERT Micro 10G is a low cost, easy to use, all-in-one XFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, diagnostic monitoring, and wavelength tuning (per XFP capability). Additionally, with a click of a button, the Eye-BERT Micro 10G will automatically test an XFP module based on the information it reads from the transceiver and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
product
Aerial Fiber Optic Cable
AFL offers a complete portfolio of fiber optic cable, supporting hardware and compression accessories that are designed to meet the most demanding transmission and distribution environments. As the leading world manufacturer of fiber optic cable, AFL is uniquely positioned to provide a full line of all-dielectric self-supporting (ADSS) aerial cables and Optical Ground Wire (OPGW) as well as supporting hardware and accessories.
-
product
Fiber Optic Test Kit
FTK-130
The SYOPTEK FTK series Single Mode/Multimode Fiber Optic Test Kit is the perfect all-in-one fiber optic test equipment kit. The FTK kit provides a wide selection of fiber optic testing, cleaning, and inspection equipment to enable technicians to install, troubleshoot and maintain fiber optic networks. It is really a cost-effective and easy-to-use solution for testing single mode and multimode fiber optic networks, troubleshooting of fiber networks.
-
product
Fiber-Optic Transmission
Fiber optic transmission systems all use data links that work similar to the diagram shown above. Each fiber link consists of a transmitter on one end of a fiber and a receiver on the other end. Most systems operate by transmitting in one direction on one fiber and in the reverse direction on another fiber for full duplex operation. It's possible to transmit both directions on one fiber but it requires couplers to do so and fiber is less expensive than couplers. A FTTH passive optical network (PON) is one of the only systems using bidirectional transmission over a single fiber because its network architecture is based around couplers already.
-
product
Fiber Optic Transmitter/Receiver & Repeater Board
To be used with 1000 micron plastic fiber optic cable. Fiber distance should be limited to 40 meters unless special low-loss fiber is used. These units can be used as repeaters to go greater distances.
-
product
Fiber Optic Pressure Sensors
Opsens Solutions optical pressure sensor delivers reliable results in harsh environment. Opsens Solutions OPP series fiber optic pressure transducers are designed to provide accurate pressure measurement in the most adverse conditions. Its small size and EMI/RFI/MRI immunity makes it the ideal sensor for industrial applications.
-
product
Fiber Optic Sensors
Leuze electronic GmbH + Co. KG
Plastic fiber optics are suitable for universal applications with low space requirements for object detection. Glass fiber optics are used in demanding environmental conditions with high temperatures and are resistant to chemicals. For radiation through foils or applications with high light power, they offer further advantages through the especially low damping. The flexible fiber optics with various head shapes can be integrated in nearly any system design. The detection range is dependent on the fiber optics and amplifiers used. Fiber optics can be used with the throughbeam principle or with scanning function. As a fiber array with multiple light beams, they can be used to detect especially small objects.
-
product
Single Mode Fiber Optic Rotary Joints
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
product
Fiber Optic Connectors
TE's fiber optic connectors accommodate 10G Ethernet — with the capacity to handle next-generation 40G and 100G when needed — without the severe distance limitations of copper cable. Easy to maintain in the field, and reliable when operating in harsh environments, our fiber optic cable connectors offer significant size and weight savings. Our broad portfolio includes several fiber optic connector types including standard fiber connectors, LC connectors and SC connectors.
-
product
Fiber Optic Tool Kits
SYOPTEK has done fiber optic tool kit assembly for the fiber optic industry for over 8 years, from fiber optic cleaning kit to fiber optic tester kit, from fiber optic inspection kit to fiber optic splicing kit...providing kits that meet varying needs of customers, and withstand the rigors of field fiber optic application use.
-
product
Fiber Optic Amplifier
Shanghai Pubang Sensor Co.,Ltd.
1. High response frequency, detect with super high speed2. Suitable for detecting small objects3. Non-contact, non-destructive detection,can be used in harsh conditions4. Simple mounting by DIN connection
-
product
FluorOptic Fiber Optic Temperature Sensors
Advanced Energy’s Luxtron® Fiber Optic Temperature Sensors enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. Based on Fluoroptic® technology, each individual product can be configured for specific applications.
-
product
Fibretool Portable Fiber Optic Inspector - HW-700V
Shanghai Fibretool Technology Co.,Ltd.
● 2.7 inch handheld DM27 monitor;Brightness and contrast adjustment● Quick navigation, get image within 3-5 seconds; Two-way focus control● 95% Image centralization, Clear image, no interface, no flash● 27 types of adapters tips available to inspect different connectors and angle-mounted connectors with limited access space● Precise resolution (<1 um), no shadow or vignetting in screen● Reliable output signal, no default under repeated operation● Various monitors can be chosen with specific display capability
-
product
Fiber Optic Circulators
Nanning Xionghua Photonics Technology
Fiber Optic Circulators by Xionghua Photonics
-
product
Fiber Optic Cable
Is an assembly similar to an electrical cable but containing one or more optical fibers that are used to carry light.
-
product
Fiber Optic Instruments
Tempo Communications provides a comprehensive line of fiber optic testing solutions that enable tech... nicians to install, commission, and document P2P and FTTx installations. Accurate troubleshooting is made effortless with the 930XC family of OTDR’s, optical power meters, visual fault locators, and the fiber identifier, while installing fiber has never been easier with the fusion splicer, fiber cleaver, splice on connectors, and fiber hand tools. Elevate your fiber game with Tempo!Show less
-
product
Fiber Optic Contacts
VPC offers Multimode and POF patchcords designed to meet a variety of fiber optic cabling needs.
-
product
SFP Based Fiber Optic Test Solution
Eye-BERT Micro
The Eye-BERT Micro is a low cost, easy to use, all-in-one SFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, and optical power and temperature monitoring (per SFP capability). Additionally, with a click of a button, the Eye-BERT Micro will automatically test an SFP module based on the information it reads from the module and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
