Vehicle
a means of conveyance.
See Also: Conveyance, Transport, V2X, Truck, Electric Vehicle, Car, Automotive, Autonomous Vehicle, Autonomous Underwater Vehicle, J1939, Motor, Fuel, Payload, Cargo, NVH, Spacecraft
-
Product
Low Gauge Vacuum Tester
G4103
-
Suitable for use on all petrol engines and easily fits to most vehicles. Accurately measures pressures within the range minus 1 bar (30mHg) to plus 0.7 bar (10psi). Applications include: Engine Fault Finding, by using the gauge as an inlet manifold vacuum tester the following faults can be diagnosed: spark misfires, poor engine compression, mixture tool weak or too rich, ignition too advanced or too retarded, inlet manifold and carburettor air leaks, incorrect valve timing. Turbo boost gauge; testing boost pressure up to 0.7bar (10psi) and Petrol Pump Tester; tests electrical and mechanical petrol pumps (excluding high pressure pumps used on fuel injection engines)
-
Product
Acceleration Testing
-
The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
Product
4/5 Pin Trailer Harness Checker / Towing Maintenance Kit
#8026
-
Innovative Products of America
Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
Product
High Speed Load Cell Test Interface
LCIC-4CH
-
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
Product
CTDs: Profiling
-
Profiling CTDs make continuous measurements as they travel through water. When lowered over the side of a ship or integrated with an autonomous vehicle, they map a vertical column of water's characteristics. Compared to moored CTDs, profiling CTDs account for dynamic errors introduced by moving through water and sample rapidly to generate a high-resolution dataset over a short period of time. Sea-Bird Scientific profiling CTDs are:*Designed to perform under unique dynamic conditions found on moving platforms.*Pumped and ducted for constant flow to match temperature and conductivity response.*Plumbed so measurements are made on the same sample of water with a predictable delay and predictable flow effects.*Built with a rugged design for shipboard and autonomous deployments.
-
Product
VPX Processing System
CRS-D4I-3VB1
-
4-slot, SWaP-reduced, rugged VPX Intel base plate cooled data processing system that can be applied across various applications including civilian and military unmanned vehicles, manned commercial and military aircraft, helicopters, over- and underwater research vessels, ground vehicles, and locomotives.
-
Product
On-board Emissions Measurement System
OBS-ONE PM unit
-
OBS-ONE PM unit is the industry-leading on-board Particulate Matter (PM) measurement system. It collects PM on a filter paper, using a partial flow gravimetric sampling method, while simultaneously measuring real-time PM. A key feature of this design is the use of a venturi flow meter which enables reliable proportional sampling and accurate exhaust gas flow measurement under transient flow conditions. Combine the GAS unit and PM unit to perform certification tests on heavy duty and non-road vehicles.
-
Product
Dual-Vision Sensor for Intersection Control and Safety
TrafiSense2 Dual
-
FLIR TrafiSense2 Dual combines best-in-class thermal and visual imaging technology with advanced video analytics to provide vehicle and bicycle presence detection at signalized intersections, day and night. Thermal imaging lets traffic operators see in total darkness and inclement weather. The daylight camera offers additional visual verification for such incidents as wrong-way drivers and animal crossings. In addition, FLIR's analytics capture accurate traffic data, making FLIR TrafiSense2 Dual ideal for real-time traffic management in urban environments.
-
Product
Combination Emissions Tester on Trolley for the Measurement of Diesel- and Petrol-Powered Vehicles - Low Weight, Short Warm Up Time
MCT T | VP 135225
-
Maschinenbau Haldenwang GmbH & Co. KG.
The combination tester on trolley is designed for the measurement of petrol- and diesel-powered vehicles. In addition, low weight, compact design and short warm-up time ensure easy handling.
-
Product
3D Acceleration Logger Sensor
NUL-227
-
This is a 3D (three dimensions) acceleration sensor which displays each dimension one at a time. It allows measuring the acceleration of moving bodies such as a body oscillating in a spring or in a moving vehicle.
-
Product
Sensor Tester
QST-5
-
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
Product
NI Vehicle Radar Test System
-
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
Product
ISDD Tool Suite
-
The Integrated System Diagnostic Design or ISDD Tool Suite provides a start to finish solution for meeting all the diagnostic needs of system design. The ISDD design process is centered around functional modeling of systems which is used to develop the diagnostics and failure analysis necessary to fully support good system design. This includes: *Analysis of Fault Detection and Fault Isolation.*Analysis of critical failures and their impact upon safety.*Detecting and reducing false alarms caused by diagnostics.*The impact of prognostics upon fault detection/fault isolation and mitigation of critical failures.*Development of vehicle health management and troubleshooting diagnostics
-
Product
Engineering Test & Development Tools
-
Besides DG’s aftermarket diagnostic tools, DG Technologies also offers several engineering tools for vehicle network development. DG’s hardware and software products are used by a variety of engineering customers such as test engineers, production engineers, and fiber optic testers. Our customers use DG interfaces for manipulating messages, datalogging, and ECU end-of-line testing over various multiplex networks.
-
Product
Opacimeter on Trolley for the Measurement of Diesel Vehicles
MO T | VP 135044
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter on trolley is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
Product
SenseNet CAN + 802.11b Sensor Controller and Telematics Module
SenseNet CAN
-
The award winning SenseNet Telematics Module features all of the connectivity required to implement powerful and inexpensive Telematics solutions for military and commercial vehicle applications. SenseNet is currently in use in commercial and military vehicle applications requiring both wired and unwired sensor network connectivity and support in Condition Based Maintenance projects.
-
Product
PCI-8531, 1-Port, CANopen Interface Device
781060-01
-
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PCI‑8531 can transmit or receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. It also features a batch SDO editor with EDS file integration and LSS services support for slave node configuration.
-
Product
Material Compatibility Test System (MCTS)
-
Automotive squeaks occur when materials in contact rub against one another causing annoying noises from friction-induced stick-slips. Automotive itches are a special category of squeaks that can develop when rubber or plastic rubs against glass or paint. The MB Dynamics Material Compatibility Squeak & Itch Test System (MCTS) is designed and manufactured to subject contacting pairs of materials and actual vehicle parts to precisely controlled interference & motion under in-vehicle environmental conditions in order to acquire, monitor, analyze and report friction and acoustic characteristics with the objective to:
-
Product
Chassis Dynamometers
-
Eddy current, Water brake and AC motoring chassis dynamometers for dyno testing heavy-duty on and off-highway vehicles.
-
Product
Multibeam Echosounder - Subsea
SeaBat T20-S
-
The T20-S is a new addition to the leading SeaBat product range engineered from the ground up to evolve with your business.Combined with the all-new Subsea Sonar Processor the T20-S provides the highest quality survey data in a fully integrated sonar processing and data storage unit housed in a subsea pressure vessel. Smaller form factor and reduced operational power to extend mission time for battery powered underwater vehicles. Internal data storage for self-contained survey solution, and interfacing via standard Ethernet to reduce integration time.
-
Product
Electric Vehicle Module Test System
FTV
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LBattery Module TestingStart/Stop TestingTraction Battery TestingSupercapacitor / Ultracapacitor TestingDrive Cycle Testing
-
Product
Driver Vision Enhancement System for Today’s Vehicles
PathFindIR™ II
-
PathFindIR II is a powerful thermal night vision system that helps you clearly see road hazards in total darkness, and it will alert you to nearby vehicles, people, and animals. Headlights typically illuminate about 450 feet straight ahead, but PathFindIR II detects heat without a need for light, allowing you to see up to four times farther down the road. You’ll have visibility through dust, smoke, or fog, and better capability to avoid an accident.
-
Product
12V/24V Jump Start System for Service Vehicles
Super-Boost-All
-
The Super Boost•All® is designed to be mounted on your service vehicle with 2 or 4 auxiliary jump starting batteries to start 12 or 24 volt vehicles. The auxiliary batteries are charged from the service vehicles electrical system through the internally mounted battery separator.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510A
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
-
Product
Land Platform Inertial Navigation Unit
Epsilon™
-
Versatile, Epsilon™ family provides advanced applications, even in GNSS denied environment: navigation (position & heading), aiming aid, driving aid. It covers all tactical applications from logistic to infantry fighting vehicles, as well as main battle tank.- Can be integrated with small artillery caliber to provide precision pointing- Connectable to any Battle Management system- Immune to magnetic disturbances
-
Product
Axle Damping Test Bench
C_MSD C 2.5 W220 | VP 215047
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
Product
Test Automation System for Durability Testing
STARS MATS
-
STARS MATS is a Mileage Accumulation Test System application available with the STARS Automation platform for chassis dynamometer. The application provides test execution, equipment control, refueling, and vehicle state monitoring to perform long endurance test without the necessity of continuous staff presence. Its flexible design offers a wide range a customization, and it addresses the different testing requirements from manual to fully-automated operation.
-
Product
Advanced Vehicle Field Testing
-
Being responsive to customers’ is the top priority at Trialon Corporation. Trialon has a long-standing commitment to supporting our customers’ requirements on time every time, especially considering the speed of technological developments in Advanced Driver Assistance Systems (ADAS) and fully autonomous vehicles.
