Optical Network Analyzers
See Also: Network Analyzers, Vector Network Analyzers, Electrical Network Analyzers, Portable Network Analyzers, Power Network Analyzers, Radio Network Analyzers, Scalar Network Analyzers, Wireless Network Analyzers
-
Product
Optical Laser Source
SAT-3E
-
Shaanxi Aitelong Technology Co., Ltd
SAT-3E optical laser source fits to optical power meter to measure fiber loss and evaluate transmission performance. They are indispensable tool for optical network installation, trouble shooting, maintenance and widely used in LAN, WAN, CATV, remote optical network, etc.
-
Product
Portable Analyzers
-
The key to the operation of Alpha Moisture Systems' Portable Analysers is the unique Desiccant Dry-Down Chamber. By keeping the sensor dry between tests, the special assembly of the head ensures that the instrument is always ready for immediate use. The head assembly consists of two chambers which have a telescopic action. When the head assembly is in the 'closed' or 'Dry-Down' position, the sensor is completely surrounded by desiccant, which absorbs the remaining water moisture from the sensor and hence it is dry and ready for use. The small space at the bottom of the test chamber enables the sample pipe to be purged before the test commences without wetting the sensor. By placing a finger over the outlet of the head, the sample pressure is able to open the test chamber automatically, exposing the sensor to the gas being tested and enabling accurate reading of moisture content in the sample gas. After each test the head assembly is closed by depressing the inner section so that the sensor will again be dried by the desiccant, leaving the sensor ready for use time and time again. The desiccant is kept in the inner chamber and is not exposed to ambient room air or the sample gas, therefore there is no need for frequent regeneration or replacement of the desiccant.
-
Product
Filtering Network TAPs
-
Filtering network TAPs allow you to filter out the packets and traffic that is not needed by the tool to perform its function. Filtering ensures that monitoring ports do not become oversubscribed with unneeded data. Filtering TAPs are purpose-built hardware devices that let you see every bit, byte and packet.®
-
Product
Multichannel Analyzers
-
Multichannel Analyzers (MCAs) are workhorse instruments in many scientific measurements. An MCA analyzes a stream of voltage pulses and sorts them into a histogram, or “spectrum” of number of events, versus pulse-height, which may often relate to energy or time of arrival. The stored spectrum may then be displayed and analyzed.
-
Product
Serial Analyzers
-
This product enables passive monitoring, debugging, and target system analysis of all speeds of Serial RapidIO Gen2 and Gen1 from the physical coding-sublayer (PCS), through serial protocol, to full-duplex link protocol exchanges. Stimulus transmitters allow for injection of SRIO packets, control symbols, and 8b/10b characters.
-
Product
Networking Solutions
Wi-Fi® Modules
-
Silicon Labs' all-inclusive Wi-Fi module are targeted for applications where excellent RF performance, low power consumption and easy application development together with fast time to market are key requirements.
-
Product
Powerline Analyzer
SHARK 100-S
-
Amperis introduces one of its most advanced Sub-Meters. This high performance product is designed to measure the use of electrical energy with an accurate degree of billing and send that information by the most advanced means of communication. The unit supports RS485, Ethernet RJ45 or IEEE 802.11 Wi-Fi ethernet. This allows it to be installed anywhere in the building or construction and communicate with the Cetral Backup Software easily, quickly and automatically.
-
Product
Optical Power Meter
-
Wuhan Sunma Technology Co., Ltd.
Optical Power Meter (OPM) is an essential fiber test instrument used for absolute optical signal measurement as well as fiber optic loss related measurement. The term usually refers to a device for testing average power in fiber optic systems. Fiber optical power meter is a tool for telecom and CATV network. This handheld optical power meter features ingenious appearance, wide range of power measurement, high accurate test precision and user automatic self-calibration function.
-
Product
3D Optical Profilers
-
ZYGO's 3D Optical Profiler instruments enable precise, quantitative, ISO-compliant, non-contact surface measurement and characterization of micro- and nano-scale surface features, capturing up to two million data points in just seconds. Applications range from topography and waviness to roughness and microstructure characterization on samples as that vary from ultra-smooth sub-angstrom optical surfaces, to extremely rough and diffuse 3D printed surfaces.
-
Product
Logic Analyzer
LAP-322000U-A
-
Zeroplus Technology Corperation
Sample rate (Internal clock): 200MHz asynchronous operationSample rate (External clock): 100MHz synchronous operationMemory Depth (per channel): 2MbitsChannels: 32CH
-
Product
Optical Channel Monitor
-
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
Product
Open Optical Encoders
-
An optical encoder is an electromechanical device which produces an electrical signal output proportional to the linear displacement of a linear guide or the angular position of an input shaft.Open encoders are exposed and feature no external integrated enclosure. The advantages of open optical encoders include the effective elimination of backlash, shaft wind-up (torsion) and other mechanical hysteresis errors.A rotary open optical encoder consists of a position measurement readhead and an accurate rotary scale marked either on the periphery of a ring or on the face of a disc.The readhead measures position by optically sensing the regularly-spaced scale markings and outputs this information as an analogue or digital signal.The signal is subsequently converted into a position reading by a digital readout (DRO) or motion controller.
-
Product
x1149 Boundary Scan Analyzer
N1125A
Boundary Scan Analyzer
The x1149 is a tool for engineers to perform structural test such as opens and shorts tests on their PCBAs. It also performs In-System Programming for devices such as FPGAs and CPLDs.
-
Product
Process Analyzers
MARGA
-
MARGA is a fully autonomous sampling and measurement system that continuously measures the water-soluble gas and aerosol components that have a direct effect on air quality. These results can then be used to study the formation of aerosols from their precursor gases and how their concentration and composition vary with diurnal and seasonal cycles.
-
Product
Automated Optical Inspection
K Series3D
-
K Series and K Series3D are the reference in Automated Optical Inspection (AOI), allowing 2D and 3D inspection with very low false calls rate, for both pre-reflow and post-reflow. They are the most powerful gatekeepers to guarantee high quality level for the assembled PCB.
-
Product
Power Analyzers
-
Power Analyzer can be used in any company that produces equipment consuming electric energy. Optimizing energy consumption not only protects the environment but also results in higher product quality. Power Analyzer are therefore excellent tools for research, development, quality control, maintenance and education.
-
Product
Power Analyzer
-
Shenzhen Graigar Technology Co.,Ltd.
This power analyzer is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyser clamp is equipped with data logger.
-
Product
Precision Resistor Network
-
Analog Devices provides a portfolio of quad resistor networks with excellent matching specifications over the entire temperature range. All of our resistors can be accessed and biased independently, making them a convenient and versatile choice for any application that can benefit from matched resistors. Our resistor networks provide the precise ratiometric stability required in highly accurate difference amplifiers, voltage references, and bridge circuits.
-
Product
TDL Network Simulation
-
Curtiss-Wright Defense Solutions
The need for realistic and effective military training simulations is fundamental to prepare warfighters for the challenges they may face on the field. The TCG portfolio of advanced tactical data link solutions enables the creation of configurable high-fidelity simulations, both real-time or scripted, of the industry’s most prominent data link protocols and standards.
-
-
Product
SFP Optical Transceivers
-
Advantech's Small form-factor pluggable (SFP) transceiver modules provide a variety of speed, distances, and wavelengths to fit any need.
-
Product
Logic Analyzers
-
A Keysight logic analyzer helps you minimize project risk by providing the most reliable, accurate measurements and the most complete view of system behavior. This comprehensive family of logic analyzer offers the measurement capabilities, probing, logic analyzer application support and analysis tools to meet your toughest digital debug needs.
-
Product
Netlist Analyzer
GateVision
-
GateVision PRO is the third generation of graphical netlist analyzers from Concept Engineering. Completely rewritten to run on modern 32/64bit platforms, GateVision PRO provides the designer of even the largest chips with intuitive design navigation, schematic viewing, logic cone extraction and interactive logic cone viewing for debug support and design documentation.
-
Product
Optical Encoders
-
Rotary encoders are ideal for use as digital panel controls or position sensing devices in a wide range of applications where digital circuitry is used. These devices are available in contacting and optical types and in various resolutions. Some models are available with push momentary switch and detents.
-
Product
Optical BGA Inspection
-
Imaging hidden solder joints of BGA, IBGA, FlipChip, CSP, CGA and SMD components
-
Product
Optical Communication Probes
-
Abacus Electrics ANSI Type 2 optical probes utilize infra-red LED technology to provide a galvanically isolated, bi-directional communications interface between energy meters and laptop computers or handheld devices for onsite data retrieval, programming and diagnostics.
-
Product
Network Analysis
-
Network development solutions come in different formats to support the variety of applications, such as network analysis or node emulation. Network analysis is crucial throughout the development of any networked system or module. The ability to capture, view, and record messages allows monitoring of bus integrity or troubleshooting functionality of the modules on the network. Whether developing a concept or preparing for production, access to the network is essential. Node simulation can be done with software, such as ATI's CANLab Software, or hardware components, possibly CANverter, depending on whether the environment is on the bench or in the vehicle.
-
-
Product
Network Security Appliances
-
Full range network appliances for applications such as NGFW, UTM, DPI, IDS/IPS, comes with scalability, modular design, reliability & manageability.
-
Product
Digital Electrical Network Analyzer
4126 NA
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 Characters LCD.● Auto-ranging / Auto-off.● One Push Button Operation.● Low Consumption.● Better than 3% Accuracy(0.05-50Ω).● Wiring Integrity Check(display + LEDs).● Over temperature protection and indication.● Stores previous readings.
