Measuring Receivers
measure radio signals.
-
Product
PC Vibration Measuring System VibroMetra
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
*The system was designed for typical tasks of vibration measurement. No ballast by unwanted functionality. *The system is modular making it upgradeable and particularly economic with fewer channels.*The necessary hardware is very compact which makes it particularly suited for mobile use.*Short installation and training time. After a few minutes you may start with the first measurement.*Off-line measurement: VibroMetra permanently saves the raw data stream of the sensor signal in the background. By this means you may analyze your measurement later again with other settings or other software instruments.*Data export as graphics, text or binary file
-
Product
TIM (Thermal Interface Material) Measurement System
-
Thermal Engineering Associates, Inc.
A system for the measurement of thermal conductivity of a wide range of thermal interface materials - grease, pads, foils, etc. - with a measurement range of of roughly 0.1 to 500W/m-K. (>500W/m-K available on custom basis.)
-
Product
Flow Measurement Products
-
With ABB's knowledge about flow measurement and management, you have access to over 100 years of flow measurement and control experience to help you save cost and increase profits.
-
Product
Water Flow / Pressure Measurement
-
Uses the same measurement principle as Fuji's ultrasonic flowmeters of which a great number have already been delivered.
-
Product
Heavy-Duty Antenna Measurement System
-
0 to 360 degree AZ+/- 90 degree EL Dual-axis high-resolution antenna positionerTwo Precision SMA measurement cablesIncludes DAMS Antenna Measurement Studio ProComplete package includes all accessories
-
Product
UFL Measurement
-
Many of the well known VNA manufacturors offer very expensive calibration kits and special phase-stable cables (which costs almost as much a MegiQ VNA) for measuring impedances. This is useful for some special scientific measurements, or when working in the higher GHz, but a setup with an uncooperative cable and a bulky (N) connector is not suited for measuring the small devices that we are developing.
-
Product
Inertial Measurement Units
IMU
-
The Inertial Labs Inertial Measurement Units (IMU) contain three highly accurate advanced MEMS gyroscopes and three high-performance accelerometers. The IMU-P and Kernel are calibrated within their operating temperature range to achieve maximum end-user usability. This also ensures tactical grade performance regardless of the environment in which it is used.
-
Product
Differential And I/Q Device Measurements
S95089B
-
The S95089B combines source-phase control of multiple internal or external sources with frequency-offset mode, enabling simplified test of I/Q modulators/converters, differential mixers, and harmonics or amplifiers.
-
Product
Digital Torque Meter Torsion Measurement
HN-10
-
Shenzhen Chuangxin Instruments Co., Ltd.
HN series digital torque meter is a general-purpose portable torque load test instrument, has the characteristics of small volume, light weight, easy carrying, multiple functions, high precision, etc., and is applicable for torque tests of various products and experiments on correcting component torque destruction, etc. Small-sized experiment machines with different purposes can be formed through combining with various machine stations and cramping apparatuses.
-
Product
RTD Measurement for PCI
PCI390
-
The PCI390 features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm-limit checking. Sensor-data is available in °C, °F, K and Ohms. All inputs are optically isolated from the system.
-
Product
Scalar Mixer / Converter Measurements
S97082B
-
The S97082B scalar mixer/converter measurements enables the highest accuracy for scalar conversion–loss/gain measurements with a simple setup and calibration
-
Product
Field Strength Measuring Instruments and Sensors
-
MAGNET-PHYSIK Dr. Steingroever GmbH
Field strength measuring devices are measuring devices for measuring the magnetic flux density B (formerly also called induction) and the magnetic field strength H of direct and alternating fields. They are also called Gaussmeters or Teslameters.
-
Product
Partial discharge measurement with remote wireless reading
PD-LT
-
The PD-LT allows online partial discharge detection on cable accessories such as cable head for safety and maintenance purposes.The PD-LT indicates the intensity of the partial discharges, converting the electrical charge units (pC) into decibels (dB). Thus the reading is kept as a simple intensity level indication, proportional to the probability of a fault's presence in the tested medium voltage accessory.The remote display gives a dB value of the probe's measurement. The dB value will vary along with the discharges indicators on the PD-LT probe. The measurement range is from 0 to 65dB and the display will show ''OL'' if the reading is over 65dB.
-
Product
Torque Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Torque Measurement Trainer comprises of strain gauge based reaction type torque transducer, fulcrum arm of 1 M length with L angle to mount the sensor, Pan & weights with digital torque indicator to read the torque in Kg-m.
-
Product
CO,CO,light and Sound Measurement
-
Everyone is exposed to different environmental influences in their day-to-day lives. For example, in an average workplace illuminance, sound level, and indoor air quality are all significant factors that influence people's performance and well-being. Testo offers suitable measuring instruments for controlling each of the measurement parameters of lux, sound, and CO2 (for indoor air quality).
-
Product
Contactless Lifetime Measurement and Inhomogenities Device
MWR-2S-3I
-
Lifetime determination is based on measuring photoconductivity decay after pulse light photo-exciting with usage of reflected microwave as probe.Simultaneous IR light transmission gives possibility to detect any inhomogenity insidesilicon brick and made 3D image of defects.
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
Vector And Scalar Mixer/Converter Measurements
S97083B
-
S97083B provides fully calibrated conversion gain/loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers
-
Product
Return Loss, Impedance & Balance Measurement Accessory
Model SLM620-1
-
For Loss- Frequency Range : 300Hz to 620KHz.- Impedance : 60 to 1000 ohms (40dB maximum).- Accuracy : ±1dB (upto 300KHz) ±2dB (300KHz to 620KHz).For Impedance- Frequency Range : 300Hz to 620KHz.- Impedance : 60 to 3000 ohms.- Accuracy : ±10% (upto 300KHz) ±20% (300KHz to 620KHz).
-
Product
Peak Voltage Measurement
-
In high voltage measurement technology, the peak value, or the effective value, of the voltage is determined in accordance with VDE 0432 or IECV 60060. The peak voltage measuring device from MPS Mess- & Prüfsysteme GmbH can measure these two values in connection with a high voltage divider (capacitive or resistive). In the event of flashovers in the high-voltage circuit, this is indicated in the SMG.
-
Product
40Gb/s DQPSK Receiver
-
The integrated DQPSK receiver incorporates an optical phase demodulator (delay-line interferometer or DLI) with 2 pairs of balanced photo-diodes and 2 linear TIAs into a single butterfly package. Compared with the currently available discrete solution in which a separate DLI and a separate receiver are used, the integrated DQPSK receiver eliminates labor intensive fiber routing and coupling (between the DLI and the balanced receiver) as well as the skew control. Moreover, the integrated DQPSK receiver offers a smaller footprint suitable for today’s demanding high speed transponder applications.
-
Product
Measuring Devices For Nanoindentation
-
With our measuring devices, you can determine the mechanical properties of thin coatings reliably and accurately. From protective paint coatings to hardness of PVD coatings: We have the right solution for you. We offer you powerful and easy-to-use measuring instruments for the laboratory and production. You can choose from a wide range of accessories to adapt your device to your individual requirements.
-
Product
Receiver Products
-
Designed specifically for high performance antenna testing, we use the latest technology to design and manufacture the fastest and most powerful system receivers in the industry. Antennas have become complex and tightly integrated RF system components, requiring more than traditional analog input receivers. Our advanced digital receivers provide analog and digital inputs, in addition to features such as pulsed measurement capability and high resolution pulse profiling, to meet these demands.
-
Product
Specific Gravity Measurement Kit
-
Simple specific gravity meters based on precision balances. Combination of Shimadzu balance and SMK Specific Gravity Measurement Kit makes handy specific gravity measuring equipment for solid samples.
-
Product
Optical Receiver Stress Test Solution
N4917B
-
The N4917B software provides an automated standard compliant stressed receiver sensitivity test according to 100GBASE-LR4, ER4 and SR4 test specification. In order to do this kind of test, several test instruments such as a bit error ratio tester, digital sampling oscilloscope, optical reference transmitter and tunable laser source are required to operate together to achieve a compliant, repeatable optical stressed eye. This stressed eye is then fed to the receiver under test, where bit error ratio is measured under the stress conditions as defined in the standard.
-
Product
Photoluminescence & Electroluminescence Measurement System (PL/EL)
PL
-
PL/EL Measurement System includes Laser, Spectrometer, Lock-in amplifier, Optical Chopper, Sample Holder(PL/EL), PMT/CCD, Fiber, Optical optics, Optical Table, Refrigerator（low temperature）,Sample Chamber and related accessories;
-
-
Product
HDMI 2.1 Receiver Compliance Test Software
N5991HP1A
-
N5991HP1A HDMI electrical performance validation and compliance software solution offers a complete test execution environment for validating and troubleshooting the electrical performance of HDMI 1.4 and HDMI 2.1 sink devices.
-
Product
Scienlab Measurement And Control Module
SL1064B
Communications Module
The Measurement & Control Module SL1064B is a rack-mount gateway for CAN- and LIN-buses with up to 6 channels. It can be used as a configurable communication interface between Scienlab Battery Test Systems and devices under test (especially their BMS) as well as additional components using CAN communication.
-
Product
Light Measurement
-
Light is produced from many natural and artificial sources. Controlling light and having an accurate understanding of its output, directionality and the appearance of what it irradiates is key to product development, quality and the success of a light source. Here are just a few examples of why Labsphere is leading the industry in light measurement.
