-
Product
Press-type Vibration Tester
9363-PC-ESS
-
King Design Industrial Co., Ltd.
This machine complies with the IEC, JIS and other 5-100Hz low-frequency specifications; applied to test the post-assembly products at end of the production line. Use resonance amplification, the product’s flaws can be screened out in advance. The operation is convenient, fast and effective.Apply Japan-imported motor; durable and safe in operation.Bellow-type damper: use special damping material that can effectively absorb vibration; allowing the test to be performed without affecting floor structure.Motor drive system is embedded in the seat; good in vibration block-out; rigidity is strong. Follow specimen to design fixture.
-
Product
Sound Level Indicators
-
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, a sound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site.An important attribute to consider when searching for a suitable sound level meter is its type or class. The type or class of a sound level meter defines the device's accuracy as per American National Standards Institute (ANSI) or International Electrotechnical Commission (IEC) guidelines. Typically, "type" is the grade according to the ANSI S1.4 standard, whereas "class" is the grade according to the IEC 61672 standard. There are two types or classes assigned to sound level meters: type 1 / class 1 or type 2 / class 2. For assessing noise in basic industrial, commercial, educational, recreational or residential applications, a type 2 / class 2 sound level meter usually will suffice. For precision-grade assessments often made in a laboratory, a type 1 / class 1 sound level meter primarily is used. PCE sound level meter products are lightweight, easy-to-use and manufactured in accordance with the highest industrial standards.
-
Product
Voltage Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
AC and DC voltage tests up to 690V with LED Comply with the latest standards IEC 61243 and IEC 61010 Novel designLarge and bright LEDs: Values are visible in the dark placeErgonomic design fits in the hand Two functions are available in one model"Measurement without battery" and "Self Test (all LED on)" Test leads withstand harsh environments at low temperature Penlight (white LED) Auto-power ON/OFF Audible indication Variable test tips, 2mm or 4mm Probe protection cover can store the attachment of caps IP65 (IEC 60529)
-
Product
Annual testing of Automatic Identification System
AIS
-
The purpose of an annual testing is to determine that AIS is operational as defined in appropriate performance standards - the International Maritime Organization (IMO) Performance Standard (MSC 74(69)) and IEC standard, IEC 61993-2: Maritime Navigation and Radio Communications Equipment and Standards Automatic Identification Systems (AIS).
-
Product
Vertically Falling Water Drops Device IPX1/2
IEC60529
-
Shenzhen Chuangxin Instruments Co., Ltd.
This device is designed according to terms and conditions of IEC60529,GB4208-2008,GB7000.1-2007,GB4706.1-2005.Satisfying requirements of level IPX1/2. Applide to test LED lamps and house hold appliances, and other electric and electronic products waterproof test of IP code level IPX 1/2.
-
Product
Vessel For Testing Bob Elements
IEC60335-2-6 Figure101
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-6 Figure 101 Aluminium Test Vessels also conforms to the clause 3.1.9.108 of IEC60335-2-9.The IEC60335-2-6 Figure 101 Aluminium Test Vessels is made of unpolished commercial quality aluminium.
-
Product
High Accuracy Revenue Meter
JEMStar ll IEC
-
AMETEK’s JEMStar II has the highest accuracy in the market, provides many communication options and monitors your power quality to make it the ideal choice for any metering application. An impressive color display makes it easy to view power measurements, phasor displays and meter diagnostics. The JEMStar II is easy to use and configure with our intuitive JEMWARE software and the meter display provides a user menu to show and edit configuration details. The JEMStar II has 1 GB of non-volatile memory to store your metering and power quality data for as long as you want. The meter has a single base model that can be used for simple revenue and billing applications as well as more complex power quality monitoring applications.
-
Product
Measuring System for Assessment of Optical Radiation Safety
IEC62471
-
The system is designed especially for the determination of optical radiation hazard exposures specified in IEC62471, such as actinic UV hazard exposure for the skin and eye, near-UV hazard exposure for the eye, retinal blue light hazard exposure, retinal thermal hazard exposure, thermal radiation hazard for eye and skin, for LED products, UV-Lamps, lighting sources, luminaires and etc.
-
Product
3.0mm Preset Controls Probe
CX-A3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts by use of a tool through holes which give access to pre-set controls. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN 61010-1, U- 3101-1, UL 3111-1 and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is stainless steel.
-
Product
Multi-Channel Digital Power Meters
66203/66204
-
Chroma Systems Solutions, Inc.
Voltage Range :15/30/60/150/300/600 VrmsCurrent Range :0.005/0.02/0.05/0.2/0.5/2/5/20 ArmsFrequency Range : DC, 15Hz~10kHzEmbedded high speed DSP, 16 bits Analog/Digital convertersHalf rack size, 4 input modules design (66204)Support different wiring configuration power measurement (1P2W/1P3W/3P3W/3P4W)Support external shunt and CT for higher current measurement application5 mA minimum current range & 0.1mW power resolutionMeets ENERGY STAR / IEC 62301 /ErP measurement requirementsAccumulated energy methods for unstable power measurementUser-define criteria provides automatic PASS/FAIL indicationsDual current shunt design provides high accuracy over a wide current rangeTHD and user-specify order distortion measurementInrush current and energy measurementVoltage/ Current harmonics measurement up to 50 orders
-
Product
IEC60884 Fig38 Thermal Compression Test Device For Plug Testing
IEC60884 fig38
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig38 thermal compression test device for plug testingUsed to evaluate the pressure resistance of electrical accessories and wall mounted mounting boxes under heatStandard: GB2099.1-2008 Articles 24.19 and 25.4 and Figure 38, IEC60884-1 Figure 38, etc.
-
Product
Linux Handheld Computer – OPAL
-
Signals & Systems India Private Limited
OPAL is a handheld computer used to download data from electronic tri-vector meters, supporting different protocols like IEC, ANSI and PACT. OPAL can be interfaced with the portable printer for spot billing applications.OPAL comes with Linux Operating System. OPAL is available in memory sizes ranging from 128 MB to 16 GB.
-
Product
Exposure Level Tester
ELT-400
-
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
Product
MCB Tripping Current Characteristic Test Bench
-
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
Product
Immunity DC
PGA 1240
-
The power generator PGA 1240 is suitable for EMC testing in accordance with standard IEC / EN 61000-4-16 in the frequency range from DC to 300 kHz.
-
Product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 90 KW / 135 KVA
SL1215A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
VMEbus
-
VMEbus (Versa Module Europa bus) is a computer bus standard widely used for many applications and standardized by the IEC as ANSI/IEEE 1014-1987. First developed in 1981 and continues to see widespread use today.
-
Product
Protective Relay Test Kit
PW460
-
PW460 Protective Relay Test Kit is the comprehensive protection relay testing equipment for all types of protective relays with high accuracy. This relay test kit has in-built output monitoring and recording function and supports testing IEC 61850 digital relay.
-
Product
Verification Of Maximum Withdrawal Force Test Apparatus
IEC60884 FIG 18
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG 18 verification of maximum withdrawal force test apparatusThis device complies with the requirements of GB 189.1-2008 Figure 18/19, IEC884 Figure 18/19, VDE0620, etc. It is suitable for checking the maximum force required to pull the plug out of the socket and the single pole pin pulled out from the socket assembly. Whether the minimum force required is within the range specified by
-
Product
Rain Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Rain Test Chamber is used to test anti-rain and waterproof performance for products, the products such as .steam locomotive lamps, wiper performance, waterproof bands, motorcycle instruments, defense industry, navigation systems, missiles, radar cone top, aerospace industry, IEC IP code specifications that need an additional discussion.
-
Product
Vibration Test Systems
G-5 Series
-
Both Shock tests at from relatively high acceleration(max. 4900m/s2 -500G) to low acceleration with wide pulse width, difficult to achieve with conventional Shock Test Systems and Vibration tests for not only IEC, MIL and JIS but also requiring higher acceleration, velocity and displacement than ordinary VTSs can be carried out with one system.
-
Product
Damped Oscillatory Magnetic Field Immunity Tester
DOMF61000-10
-
DOMF61000-10 damped oscillatory magnetic field immunity test system included damped oscillating wave generator and single ring coil, it’s designed for to do damping oscillation magnetic field immunity test and fully meet IEC 61000-4-10, EN61000-4-10 and GB/T 17626.10 standards requirement.
-
Product
Ball Pressure Test Apparatus
CX-Q03
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Ball Pressure Apparatus is used to check the integrity of dielectric materials by exerting 20N force. The BPA10 is called out in IEC 60335, 60950, 61010, UL, CSA and European Norms. It is used to check the integrity of dielectric materials by exerting 20N force. The Ball Pressure Apparatus is made of stainless steel for long life. Since accelerated life procedures are used for this oven test, more than one apparatus may be useful for parallel testing.
-
Product
Digital Input Board
VME-1129
Digital Input Board
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
Product
K Thermocouple Immersion Probe
TP742
-
Immersion “K” Type thermocouple probe. Tolerance according to IEC 60584-2 standard.
-
Product
Lamp caps gauges
IEC60061
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60061 Lamp caps gauges Quick Details Place of Origin: China (Mainland) Brand Name: CX Reference Standard:IEC60061-3 .
-
Product
IEC60884 Fig8 Plug Strength Compression Tester
IEC60884 fig8
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig8 plug strength compression testerConforms to the standard: GB2099-1-2008 Articles 10.1 and 24.5 and Figure 8, IEC60884-1 Figure 8
-
Product
Plug Pin Durability Test Device
IEC60884 Fig30
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig30 plug pin durability test deviceSuitable for checking the tightness of the plug pin,Check the tightness of the plug pin according to the standard, and customize the pin hole gauge of other national standards.
-
Product
Automated AC Digital Hipot Tester
-
Educated Design & Development, Inc.
1 button testing - No setup required, just plug right in! Or, make a plug for your cordless product, and plug right in! EASY!Easy to identify PASS / FAIL visible and audible indicationAuto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchSafety Protected Start Switch -- Protects user from shock!Performs the Low Current Ground Continuity test at the same timeMeets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements as well as UL 120Kohm requirementsIncludes ISO/IEC 17025 Accredited Calibration Certificate, accredited by ACLASS (Internationally accepted results... equivalent to A2LA)
-
Product
Capacitor Contactor
KML
-
Lifasa - International Capacitors, SA
The new KML contactors are designed in accordance with IEC 60947-1 and are suitable for the connection of three-phase power capacitors. Thanks to its pre-load block mounted on the same contactor, the strong current tips produced at the moment of capacitor connection are reduced and the contactor itself is protected at the same time.
