Environmental Simulation
-
product
Portable Solar Simulator
PEC-L01
●Light source/lamp house integrated compact design ●Illumination direction can be freely rotated 360 degrees●5cm square optical filter can be attached ●Peccell 's cheapest solar simulator Combination example with PC
-
product
UV Solar Simulators
UV Solar Simulators - please contact the company directly for more information.
-
product
PXI Millivolt Thermocouple Simulator Module - 32 Channel
41-760-001
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
product
Environmental Test Chambers
Bionic Scientific Technologies
Environmental Test Chambers offer precisely controlled environment required in insect and biological research, electronics production (battery testing and PCB manufacturing) and polymer testing (plastic and rubber testing) etc. Designed ruggedly and fitted with technology advanced instruments, our environmental chambers are available from benchtop cabinets to complex large capacity walk in rooms. At Bionics Scientific, we design and manufacture environmental chambers or climatic test chambers matching with customer required specifications and supply them worldwide at factory price.
-
product
Environmental Testers
Environmental tests are used to verify a piece of equipment can withstand the rigors of harsh environments.
-
product
Axle Load Simulators
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
product
SparkFun Environmental Combo Breakout
CCS811/BME280 (Qwiic)
The SparkFun CCS811/BME280 Environmental Combo Breakout takes care of all your atmospheric-quality sensing needs with the popular CCS811 and BME280 ICs. This unique breakout provides a variety of environmental data, including barometric pressure, humidity, temperature, TVOCs and equivalent CO2 (or eCO2) levels. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
product
ESD Test Simulator
ONYX16
The ONYX is a state of the art electrostatic discharge simulator available in 16kV or 30kV versions. It is the most ergonomic 30kV ESD gun without an additional base control unit that can be battery or mains operated. The easy to use touch screen, ergonomic design, modular RC units, multilingual interface, remote control software, built-in LED light and temperature & humidity display allows for trouble-free use of the ONYX in all types of test sites.
-
product
EV/HEV Battery Pack Environmental Exerciser/Monitor System
DMC designed, built, and programmed a set of automated test stands for charging and discharging electric vehicle battery packs. The test stands also monitor the performance of these battery packs while exposed to harsh environmental...
-
product
Network Impairment Simulator
Testing system performance under realistic network conditions requires the introduction of impairments that could be expected to be seen on networks, especially public networks which are uncontrolled. There are a number of ways to do this. A basic method is to use network simulation devices that can emulate conditions expected to be encountered.
-
product
EM & Thermal Simulation Software
SEMCAD X
Schmid & Partner Engineering AG
SEMCAD X is the latest generation of 3-D FDTD full-wave simulation software offering unprecedented levels of user-friendliness, speed & memory efficiency. Its application range has been further greatly extended by incorporating the world's first EM ADI-FDTD solver.
-
product
Environmental Monitoring
Life doesn't stand still and neither do you. An amazingly intuitive web-based control panel gives you the freedom to monitor environments from anywhere.
-
product
Plastics Simulation Software
Moldex3D
Moldex3D is the world leading CAE product for the plastics injection molding industry. With the best-in-class analysis technology, Moldex3D can help you simulate the widest application range of injection molding processes to optimize product design and manufacturability, shorten time-to-market, and maximize product ROI.
-
product
NIBP Simulator
SC-4 SimCube®
The SimCube SC-4 provides all the necessary parameters for testing the basic features of a patient monitor including 3 NIBP simulations, ECG, Heart Rate Sequence, Respiration, Digital Manometer, and Peak Detect Test modes with the option to upgrade to include the OxSim SpO2 simulator and complete accessory kit. Features one-button operation for quick testing of patient monitors.
-
product
Cost-Effective Network Simulator
Emutel Maestro
Emutel Maestro brings you the perfect solution for testing your DSL equipment. Connect to your product while still in your own testing lab and perform those final tests in a real environment, enabling you to identify and solve any problems before they occur on site.
-
product
IMU MODELING AND SIMULATION
CAST Navigation’s INS systems provide high rate inertial data with exceptional fidelity to support the integration and testing of today’s complex EGI and GNSS/INS navigation systems. The CAST system is designed for optimal performance when the inertial sensor and GNSS receiver are either loosely, tightly or ultra-tightly coupled, or when an INS aiding source can be utilized by any other type of device.
-
product
ESD - Simulator
SESD 230
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
-
product
Environmental Data Logger
PeakTech Prüf- und Messtechnik GmbH
This data logger for air temperature, air humidity and temperature measurements via two Type-K sensors offers the possibility to record four measured values with the exact date and time of recording.
-
product
Environmental Testing
Environmental testing and accelerated ageing are testing that may be mandated for certain regions or required standards. But for many products, this testing is not mandated, but if any claim to performance is made then testing should be done to have evidence. In addition, it can help ensure less product returns to defective products that may after sold become faulty due to external environmental impacts.
-
product
Troubleshooting Track Circuit Simulators
14900 Series
The 14900 seriesTrack Simulator features a front panel with standard set up resistors and terminals and electrically conductive model track to simulate a track circuit suitable for instructional and hands-on training purposes. A locked drawer provides additional switches, potentiometers, and controls that allow selective implementation of many faults commonly found in typical track circuits.
-
product
Surge/wave Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Surge pulses occur due to direct or indirect lighting strokes to an external circuit. This leads to current or electromagnetic fields causing high voltage or current transients. Another source for surge pulsed is switching transients originating from switching disturbances and system faults.
-
product
Environmental Radiation Monitor "Radi"
PA-1000
Every day, wherever we go, we are exposed to minute amounts of environmental radiation.* This environmental radiation is emitted continuously, day and night, from various objects and substances in the natural world and our living environment.Most environmental radiation consists of three types: alpha rays (α), beta rays (β) and gamma rays (γ). HORIBA's PA-1000 "Radi" environmental radiation monitor makes it easy for non-specialists to measure even minute levels of gamma rays.* Environmental radiation, also known as natural radiation, includes radiation emitted from space, soil, stones, the ground and the air, as well as from manmade objects such as concrete and buildings
-
product
Simulation Software and Test Solutions
Simcenter Software
Siemens Digital Industries Software
The Simcenter portfolio uniquely combines 1D simulation, 3D CAE and test to help you predict performance across all critical attributes earlier and throughout the entire product lifecycle. By combining physics-based simulations with insights gained from data analytics, Simcenter helps you optimize design and deliver innovations faster and with greater confidence.
-
product
PCI Strain Gauge Simulator Card, 4-Channel, 1.5k
50-265-404
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
DC Load Simulating Inductors
Osborne has developed a wide range of DC load simulation inductors that are known for the transients they produce. Osborne DC load simulation inductors are unique and innovative because they are engineered to produce a precise time constant current transient during the current charge cycle.Another distinguishing feature of our load simulation inductors is that they produce a precise voltage transient during the current discharge cycle. The resulting test circuit can be used to accurately replace real loads in a variety of circuit simulation applications.
-
product
Transducer Simulator
Model 0V
SPECIFICATIONS: Impedance: 700 ohms nominal. Output Ranges: 10 turn vernier 0 - 3mV/V. Excitation: 20v ac/dc max,
-
product
Environmental Testers
AEMC manufactures a line of cost effective, hand-held instruments for measuring temperature, humidity, light, wind speed and other variables. Each instrument in this series includes sensor, backlit CD and a shockproof holster. They are battery operated and can easily be carried in a shirt pocket.
-
product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
41-752A-903
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
