References
A source of comparison.
See Also: Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Reference Transmitters, Acoustical References, Frequency References, Solar Reference Cells
-
product
Brake Fluid Boiling Point Tester With Bluetooth Printer
6513D
Peaceful Thriving Enterprise Co Ltd
This tester can measure the boil point of the brake fluid. It can obtain the wet boiling temperature of the brake fluid for technician as a reference for maintenance. It can be the reference when technician is going to change the brake fluid.The testing data print by Bluetooth printer.
-
product
Source / Measure Units
A Source/Measure Unit, or SMU, is a source and measurement resource for test applications requiring high accuracy, high resolution and measurement flexibility. SMUs are sometimes also referred to as source monitor units. An SMU can precisely force voltage or current and simultaneously measure voltage and/or current.
-
product
Microvolt DC Volt Meter
QA350
The QA350 relies on a built-in reference to calibrate the ratio between the hi and low ranges. If you have a preferred lab reference, you may use that it to improve the QA350 accuracy beyond the indicated +/- 400 PPM. For example, various vendors on eBay can provide calibrated +/-30 PPM 5 or 10V voltage references that can be used to set the ultimate accuracy of the QA350 to under 50 PPM at room temperature.
-
product
16-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - 6U VPX
Model 58132
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- 16 250 MHz 16-bit A/Ds- 16 wideband DDCs (digital downconverters)- 128 multiband DDCs- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2, &3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
product
Vibrator QC System
Accelerometer Array
*24-channel input interface for DAQLink-III acquisition system (23 for accelerometers and one for True Reference)*Computes accelerometer weighted sum using input array*Controlled state of current supplies for external accelerometers*LED status indication of every accelerometer input*Differential outputs to the acquisition system*Input channel impedance of 1 Mohm*Bandwidth: 0.1 - 5000 Hz*Crosstalk: -100 dB*Phase tolerance of channels: ±0.2 deg*10 mA current supply for every accelerometer channel*Max input signal: ±10 V p-p (True Reference), ±2.8 V p-p (Accelerometer input)*Power supply: 9 - 18 V
-
product
Semiconductor Optical Amplifiers
A Semiconductor Optical Amplifier (SOA) is essentially a laser diode (LD) with no feedback from its input and output ports and hence is also referred to as a Traveling-Wave Amplifier (TWA). Semiconductor Optical Amplifiers (SOAs) have proven to be versatile and multifunctional devices that are key building blocks for optical networks.
-
product
Voltage References
Maxim offers an industry-leading portfolio of shunt and series voltage reference ICs. We were the first to develop a series reference in a 3-pin SC70 and in chip-scale packaging. Our hundreds of voltage references include high-accuracy, low-power, low-noise, and automotive-grade products.
-
product
Dytronic Primary Transfer Ultra Stable Standard
RD-22 Ultra
The RD-22 Dytronic Primary Transfer Ultra Stable Standard represents the state-of-the-art technology in a commercially available AC transfer reference. The Ultra Stable RD-22 is a variant of the RD-22 Primary Transfer Standard that has been optimized for 120/240 V @ 5A operation to provide optimum stability. In a stable test environment, repeatability for a 10-second test of ±0.6 µWh/VAh is attained at 120 V and 240 V at 5A inputs with a 95% confidence interval. A typical experimental 2 repeatability of less than ±0.25 µWh/VAh is achieved. In a stable test environment, a reproducibility of ±2 µWh/VAh over a five-day interval is attained at 120 V and 240 V at 5A inputs with 95% confidence interval.
-
product
Spectrum Analysis, Up To 26.5 GHz
S930902B
The S930902B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 26.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
product
Optical Spectrum Analyzer
an optical spectrum analyzer for analyzing short wavelengths from 350nm to 1000 nm. Because it adopts a Fourier spectrum system with a Michelson interferometer, the 8341 can measure the coherence. With its narrow wavelength resolution of 0.01nm * , the 8341 is very effective for the evaluation of not only CD/DVD laser diodes, but also for blue-violet laser diodes. In addition, the built-in He-Ne laser acts as a wavelength reference to ensure a high wavelength measurement accuracy of ±0.01nm * . Finally, with its fast 0.5s * measurement speed, the 8341 is ideal for building into systems for mass production and evaluating temperature characteristics of system components.
-
product
Extender Card
The IEEE extender card, referred to as board PWB1000281-03. Extender card to allow for testing and debugging of the chassis assembly. This board was originally an Intel design that Dynamic Engineering was authorized by Intel to re-create
-
product
Frequency Reference
E8-X
The Quartzlock E8-X is a breakthrough in exceptionally low cost, miniature, traceable, calibration-free, off-air frequency & time standards. These references maintain the high frequency & time accuracy required for demanding applications.
-
product
Electricity Meter Test Equipment
The Reference Standard RS is precision standard meter in single- and three-phase version for electrical power and energy measurement. It is designed to meet all requirements put on a reference standard in a single- and three-phase electricity meter testing and calibration systems. The Reference Standard can be set to any true or artificial mode of operation in three phase system and is capable to evaluate individual quantities in any phase
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - XMC
Model 71751
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfacesOptional LVDS connections to the Virtex-7 FPGA for custom I/OAlso available in 3U VPX, 3U & 6U cPCI & PCIeSupports GateXpress® FPGA-PCIe Configuration ManagerSynchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Cable Assembly, Receiver, TriPaddle, 72", 200 Pin Male LFH, M3 jackscrews
540105040505
Cable Assembly, Receiver, TriPaddle, 72", refer to drawing for wire list, M3 jackscrews
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
ACCUplace Dot Patterns
AP-D Series
All machine vision lenses will show some type of distortion. Minimizing or correcting that distortion is crucial in most applications. The ACCUplace Dot Patterns target is designed to check, verify, or quantify barrel distortion in vision systems, alignment between multiple optical systems, and can calibrate instruments with both vision and motion systems. The indexed columns and rows of dot features provide reference points that make alignment and distortion detection simple and straightforward. The AP-D is offered on four standard materials; Glass (CG) Opal (OP) Photopaper (RM) and Film (TM).
-
product
1.533 Μm Frequency-Locked Laser
Thorlabs' LLD1530 Frequency-Locked Laser is a narrow linewidth, DFB-laser-diode-based, turnkey system with a vacuum emission wavelength of 1532.8323 nm and a high SMSR of at least 35 dB. The laser frequency is actively stabilized to a National Institute of Standards and Technology (NIST)-traceable molecular transition of acetylene and has an absolute accuracy at start-up that is better than ±25 MHz. The emission frequency immediately after start-up is then maintained with a ±25 MHz stability, providing an overall frequency accuracy of ±50 MHz. The LLD1530 is an accurate frequency reference designed to provide low-noise laser emission with excellent frequency stability, accuracy, and precision immediately at start-up. This source is ideal for use in demanding FTIR instrumentation, instrument calibration, gas sensing, and coherent telecommunications applications.
-
product
Eddy-Current Sensors
Eddy-Current sensors are noncontact devices capable of high-resolution measurement of the position and/or change of position of any conductive target. Eddy-Current sensors are also called inductive sensors, but generally "eddy current" refers to precision displacement instruments (or nondestructive testing probes) and "inductive" refers to inexpensive proximity switches. High resolution and tolerance of dirty environments make eddy-current sensors indispensable in today's modern industrial operations.
-
product
1-Channel DAQ Module
FMC160
Sundance Multiprocessor Technology Ltd.
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC160 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
Spectrum Analyzers
SK4M Series
*Frequency range: 100 Hz to 20/50 GHz*DANL < −165 dBm/Hz*Low Phase Noise −125 dBc/Hz at 1 GHz signal from 100 kHz offset*High Frequency Reference Accuracy ±0.1 ppm*Resolution Bandwidth Range 1 Hz to 10 MHz*Built-in Low-noise Amplifier
-
product
Humidity calibration with humidity calibrator
HUMOR 20
The role of humidity calibrations that are accurate, reproducible, and documentable is becoming more and more important. The humidity calibrator HUMOR 20 developed by E+E is the ideal reference instrument for these requirements and is traceable to international standards. The HUMOR 20 can be used in the humidity range of 10-95% RH both for monitoring cylindrical sensors and also for monitoring instruments with cubic dimensions.
-
product
Embedded LO Capability
S96084B
Enables accurate measurement of relative phase and absolute group delay of a frequency converter with a built-in LO source, without having to access a common reference signal
-
product
WinSock Trace / Debug Utilities
SocktSpy
The Socket Spy programs are Trace/Debug utilities used for monitoring WINSOCK API references between an application and the Windows Sockets Dynamic Link Library. Socket Spy/16 operates under Windows 3.1 and is fully compatible with the WinSock Ver 1.1 standard.
-
product
Signal Conditioners
General Purpose
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
product
Height Gages
Used from a flat surface such as a Starrett granite surface plate, height gages measure the distance from the reference surface to some feature of a part, and can do so with exceptional accuracy. accuracy. Starrett offers a full range of height gages. Our Altissimo advanced electronic height gage is rich in features and exceptionally accurate. gages are available with a choice of range and feature sets. Our vernier height gages are still preferred by many for their exceptional accuracy. For the highest level of accuracy, we offer DIGI-CHEK gages. These tools are typically used in combination with the various scribes, attachments and accessories available from Starrett to complete the inspection work.
-
product
FMC-HPC ADC Board
FMC121
Sundance Multiprocessor Technology Ltd.
The FMC121 provides two 16-bit A/D channels up to 1Gsps and two 16-bit D/A channels up to 1.4 Gsps data rate with a 2.8 GSPS update rate. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter and Texas Instruments DAC39J84 Digital-to-Analog converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC121 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
Class 2 Sound Level Calibrator
SPC70
The SPC70 is a Class 2 sound level calibrator suitable for periodic testing of sound level meters and verifying their accuracy before and after readings, in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB. The output is accurate to 0.5dB with low levels of harmonic distortion. The SPC70 is compatible with the Martindale SP79 Class 2 Sound Level Meter and other meters with microphones up to 25mm.
-
product
High Performance Embedded Development Kit
TySOM EDK
The TySOM™ Embedded Development Kit is for the embedded designers who need a high-performance RTL simulator/debugger for their embedded applications such as IoT, Automotive, Factory automation, UAV and Robotics. The kit includes Riviera-PRO™ Advanced Verification Platform and a TySOM development/prototyping board. TySOM boards come with either a Zynq 7000 chip (FPGA + Dual ARM® Cortex™-A9) or with a Zynq® UltraScale+™ MPSoC device. These boards include memories, and various communication and multimedia interfaces in addition to FMC connectors for peripheral expansion. Reference designs for application such as IoT, ADAS, 4K UltraHD imaging and Robotics and a complete reference design, which contains the SW (Linux) and all the hardware blocks required to support the peripherals on the board, are provided.
-
product
Meter test station
TS23
Calmet Smart Calibration Devices
Three phase reference standard of accuracy 0.02% (or 0.04%). It makes possible electricity meters testing on the site or in the laboratory up to 3x120A/600V
