Filter Results By:
Products
Applications
Manufacturers
Voltage
The tension of an electromotive force.
-
product
DC-Powered, AC Voltage Monitor
VAD/VQD
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
product
High Voltage Diode Assemblies
High voltage diode assemblies are built by adding diodes in series to yield a higher peak inverse voltage. For example, if each diode is rated for 1200 peak inverse voltage (PIV), then six diodes in series would have a total peak inverse voltage of 7200 PIV. The detailed circuit is shown below.
-
product
Voltage Tester
PeakTech Prüf- und Messtechnik GmbH
Uses voltage detection technology for the detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets and wires.
-
product
Tribocorrosion Tester
ASTM G119
Tribocorrosion involves studying Wear Evaluation of Protective Coatings. It involves mechanical and electrochemical interactions between components in motion. Rtec Tribocorrosion modules measures inline current, voltage, friction, wear, temperature , down force, ear, acoustic emissions at all times. Currently used by several Fortune 500 firms globally.
-
product
Voltmeters
ARC Flash No Volts Meter is an ultra-safe portable digital voltmeter. It can provide testing of voltage on firing and related system lines. The 620EXV is certified to meet USA MIL. STD. 810 MTD. 511, therefore compliant for use in explosive atmospheres. This product will accurately inform its operator using red and green lights (which can be set to custom levels) to indicate whether or not the voltage level conforms.
-
product
Double IC Optic Node
OX 732
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics. Green Technology incorporated - Aluminium Housing for maximum heat dissipation.- Frequency 40 ~ 1000 MHz- Optical Wavelength : 1290 ~ 1600 nm- Flatness ±0.75 dB- LED Bar Display for Optic Signal Level- High C/N, CSO & CTB Characteristics- Inward Extruded Aluminium Channels for Maximum Heat Dissipation- High Voltage Surge Protection- -11 dBm Sensitivity- RF O/P at 0 dBm : 110 dBµV
-
product
Voltage Meter
MN6I
The mezzanine is designed to measure instantaneous voltage values through six isolated channels with differential inputs.
-
product
160W Programming Laboratory Grade Power Supply
Source effect: *CV≤0.01%+3mV(mA) *Load effect: CV≤0.01%+3mV(I≤3A) CC≤0.2%+3mA(I≤3A), CV≤0.02%+5mV(I>3A) CC≤0.2%+5mA(I>3A) * Ripple and noise: CV≤1.0mVrms(I≤3A) CC≤3mArms(I≤3A), CV≤2.0mVrms(I>3A) CC≤6mArms(I>3A) * Protection Type: Overcurrent Protection (OCP) Overvoltage Protection (OVP) * Display accuracy: Voltage indication accuracy: ± (0.5% + 2 words)
-
product
0.1Hz-3MHz Functional Generator
MFG-3003
Features:*Frequency of the models: 0.1Hz~2MHz/5MHz/10MHz/13MHz/15MHz*Output waveform:Sine,Triangle,Square,±Ramp,±Pulse*Voltage Control Frequency (VCF) capability*TTL/CMOS and OUTPUT synchronous output*Less than 1% distortion at 10Hz~100kHz*Less than 0.5dB frequency response at 0.1Hz~100kHz*1Hz~30MHz frequency counter*AM/FM function optional (models with suffix "A" include this function)*FM/Sweep function optional (models with suffix "C" include this function)
-
product
Battery Pack Test System
*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery.
-
product
Portable Three-Phase Meter Site Analyzer
RW-30X / RW-31X
RADIAN RW-30/31X Meter Site Analyzers deliver comprehensive three-phase field testing and site analysis utilizing the Radian Research RX Xytronic series reference standard as its measurement engine. The RW-30/31X provides for testing meters with integrated, precision, true three-phase voltage and current sources or using customer’s load. Choose the RW-30/31X NS (no source) model to test using customer’s load only.
-
product
Mezzanine System
5081
The 5081 provides four channels of 12 bit digital to analog voltage output, with multiple single ended output ranges. Each channel is software selectable for 0 to +5V, 0 to +10V, +/-2.5V, +/-5V, +/-10V or -2.5 to 7.5V ranges. The outputs reset to 0.0 volts on power up.
-
product
Non-Contact Voltage Tester
NT-303
Contact - free electrical socket indication at AC voltages between 90V-240V. Clear alarm system: flashing LED with beeper alarm.. Quick and accurate detection of circuit breaks.. Includes a small screwdriver for easy batteries replacement.. Pocket pen-type design, easy to carry and store.
-
product
Megohmmeters
burster präzisionsmeßtechnik gmbh
Automatic / manual switch of measurement range, test voltage 45 V, 100 V, 250 V, 500 V, limit value indicator, RS232 interface
-
product
"Stiff Grid" and Parallel Operation AC Generator Excitation Regulator
SVRFP
The Kinetics model SVRFP Exciter/Regulator rectifier is designed and rated in capacity and operating parameters for the application of exciting the fields on an AC generator in parallel with other AC generators and the power system is a "stiff system" in relation to loading. A "stiff system" is a generating system that is of sufficient capacity or the generator is "small" in relation to the system grid, that the AC system voltage under impulse/step loading condition does not require forcing of the generator field to maintain the power grid voltage. Systems are designed with a standard unit service factor to operate within the +10% to -20% nominal voltage rating at 100% current rating.
-
product
Automotive Digital Multimeter, 1999 Count, Average, Manual Range, 3.5 Digit
72-9275
Full featured multimeter with additional functions for automotive diagnosis. Measures AC/DC voltage, DC current, resistance, frequency, dwell, tach, duty cycle and temperature.
-
product
Manual Flying Probe Test Systems
They provide flexible measurement technologies like Kelvin and high voltage tests in combination with low tooling costs. atg Luther & Maelzer offers a wide range of different systems starting from standard systems with 8 heads up to oversized systems with 24 test heads.
-
product
50-Pin Ribbon Conn Straight PCB Mount
40-963-550-SM
Ideal for user created termination schemes where the termination is to be remotely connected to the module by cable. Interfacing PCBs should be designed with suitable clearances for the working voltage the application requires.
-
product
48V / 300 Amp Load
EL18-48M
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
product
Battery Cell Surge Tester
19311
The Chroma 19311 series battery cell surge tester is designed for testing the insulation quality between the positive and negative plates of the lead-acid battery cell. This is done by applying a high voltage surge/impulse before the electrolyte injection. Its output voltage can reach up to 6kV. It also has four terminal measurement and 200MHz sampling rate. The Chroma 19311 series has single channel (19311) and multi-channel (19311-10) tester.
-
product
25-Pin D-Type Male Right Angled PCB
40-963-025-RM
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
product
High Performance VXI Chassis for Military ATE Systems
1261B Series
The 1261B high-performance VXI chassis serves as the standard for most military ATE systems. All 1261B chassis include full-power protection features such as overvoltage and overcurrent protection, and also incorporate a quick-check diagnostic connector to verify performance of power supply voltages, currents and specific VXI signals.
-
product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
product
64-bit PXI Extension Card
52906
The function of PXI extension card is to extend the PXI backplane signal outside of the chassis. Inserting the PXI card to extension card can easily check or measure the PXI card's signal under power on condition, which resolves the problems of inconvenient inspection due to the PXI card inside the chassis for RD or maintenance personnel. PXI extension card is able to isolate the voltage and signals sent to the PXI card for hot swap when the system is powered on. Every time the extension card activates it can supply the power required for PXI initialization. It eliminates the need for rebooting PC when users read and re-write the configuration files.
-
product
Analog I/O via Ethernet
2608 Series
16 inputs of voltage, thermocouple, or 4-20 mA16-bit A/D, 15 -bit D/AUp to 8 analog outputs with remote sensingAuto standardizationSelectable input gainAll differential inputsWatchdog TimerCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
product
Basic AC Power Source, 4000 VA, 310 V, 20 A
AC6804B
This basic AC power source offers stable, reliable power up to 4000 VA. An intuitive user interface and flexible I/O connectivity.Increase your uptime with stable, reliable AC power sourceEngineer reliability into your designs with a basic AC power sourceTest your designs with confidenceTest under real-world conditions - fluctuating voltage or transient spikesEasily access setup and measurement information
-
product
Digital/Analog Audit Kit
Botron's Digital/Analog Audit Kit insulation and continuity tester is designed for electrical testing. The wide range of test voltages makes the Audit Kit ideal for users involved with ESD testing. The kit gives greater functionality with simplified operation and an ergonomically designed case.
-
product
DC System Power Supply, 80V, 9.5A, 760W
N5748A
The single output, 760W N5748A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
product
Linear Bench or Rack Mount Power Supplies Programmable, Local or Digital Control, Ultra Low Ripple/Noise
Series PCX-MAT
These voltage stabilizers with a full complement of meters and controls, are 1/6-rack size units designed to plug directly into their own carrier cases and rack adapters. Seven models are available. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant. A modular version of PCX-MAT called PCX is also available. Contact Kepco for details.
-
product
Digital (1kV below) Insulation Tester
1651 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● ACV auto-detection function on 3 insulation ranges (250/500/1000V) and low Ω ragne before pressing the TEST button.● 68 x 34mm large LCD display.● 3½ digital LCD (2000 counts) a LCD indicated instrument for insulation(MΩ), continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● Auto ranging.● Auto power off function.● Auto data hold function.● Rel function (ohm only)● Continuity buzzer.● External AC voltage warning.● Automatic circuit discharge.● BS 16th edition.
