Instrumentation Amplifiers
A type of operational amplifier used when a circuit needs accuracy and stability.
See Also: Instrumentation, Amplifiers, Instruments
-
product
Solid State Power Amplifiers
By combining significant R&D funding with judicious acquisitions of microwave technology leaders, Teledyne Microwave Solutions (TMS) has built a strong portfolio of SSPAs supported by innovative, collaborative engineering and manufacturing teams. Covering 100MHz to 100GHz, with power from 0.1W to 10kW, TMS SSPAs include both Pulsed and CW for all markets, from commercial Satcom to military and space qualified platforms.
-
-
product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
product
6-Channel VME Pulse Amplifier
V860
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
product
High Voltage Amplifier
HA-400
*400Vp-p(±200V DC) *160mAp-p(±80mA DC) *Bandwidth: ≦600KHz(200Vp-p) *Slew Rate: 300V/us *Gain(AMPL): 0~90(10 Turn VR) *DC Offset: ≦0~±200V (10 Turn VR + SW) *Output Resistor: 50Ω
-
product
PCI, IEEE 488 GPIB Instrument Control Device for Linux
778686-01
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
VB-8034, 4-Channel, 350 MHz Bandwidth VirtualBench All-in-One Instrument
784343-01
4-Channel, 350 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8034 combines a four‑channel, 350 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
product
Dual Channel High Voltage Linear Amplifier
A400D
This unit contains two independent A400 amplifiers that share common ground reference and power supply.
-
product
Full W-Band Power Amplifier
SBP-7531142515-1010-E1
For communication and radar applications, SAGE Millimeter has released a new full W-Band power amplifier. Model SBP-7531142515-1010-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal output power of +15 dBm across the frequency range of 75 to 110 GHz. The DC power requirement for the amplifier is +15 VDC/190 mA. The mechanical configuration offers an in-line structure with WR-10 waveguides and UG-387/U-M flanges. Other port configurations, such as with 1 mm connectors or a right angle structure with WR-10 waveguides, are also available under different model numbers. Features include: Full Band, High Gain, High Output Power.
-
product
Amplifiers
Amplifiers from Analog Devices deliver both high performance and high value. These amplifier ICs combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
product
Class-D Audio Amplifiers
Analog Devices is a leader in Class-D audio amplifiers and audio signal processing, and we deliver audiophile-level performance with our proven analog and digital technology. We offer a wide range of audio amplifiers, including industry-leading microphone preamps, microphone drivers, line drivers, and receivers. Our Class-D amplifiers, in particular, are among the lowest power and lowest distortion in the industry. Our portfolio includes Class-A, Class-B, and Class-D audio amplifier offerings, along with a breadth of power ICs. Analog Devices amplifier products have been used in many high volume consumer products where the highest audio quality is expected. The lowest power consumption also enables this performance in many battery powered applications as well.
-
product
Power Amplifiers
Power amplifiers are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a high output power with superior power added efficiency (PAE) and high linearity. While standard models focus on general purpose applications, additional models with differing frequency ranges, gains and power levels are listed on the website. Custom designs are also offered to meet any user’s specific needs.
-
product
Photo Detector with Integrated Transimpedance Amplifiers
ADN3010-11
Analog Devices optoelectronic amplifiers include a range of germanium photodiodes that, through a proprietary process, have been monolithically integrated with silicon transimpedance amplifiers and limiting amplifiers. This process eliminates the need for bond wires connecting the photodiode to the transimpedance amplifier, which leads to improved performance and greater manufacturing reliability. Our portfolio of products also supports the growing need for optical and electrical interface miniaturization.
-
product
Trunk Amplifier
The trunk amplifier is designed to compensate for attenuation and additional amplification of signals from GPS and GLONASS satellite radio navigation systems as part of synchronization and common time equipment.
-
product
DSP And Power Amplifier
DMPA12
The DMPA12 is a powerful digital audio processor and multi-channel power amplifier combined into a single rack space component designed to work with DM Series processors. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency. The primary applications are sound reinforcement and teleconferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design is ideally suited to mix-minus sound reinforcement systems.
-
product
PathWave BenchVue Advanced Battery Test And Emulation Software For A Single Instrument
BV9211B
Achieve higher accuracy, repeatability, and safety with an emulation based on a unique battery model. Your model will allow you to determine your device's power consumption, emulate an actual battery, and import existing battery models.
-
product
High Voltage Op Amplifiers ≥12V
High supply voltage op amps are used in systems that demand the widest dynamic range with the best signal-to-noise ratio. Engineers turn to Analog Devices for high voltage amplifiers that deliver industry-leading performance. Increasingly, new high voltage amplifiers also offer features to improve system performance, cost, and robustness while easing the complexity of system design. New features include integrated input overvoltage protection (OVP), on-chip electromagnetic interference (EMI) filtering, higher electrostatic discharge (ESD) immunity, and greater resistance to latch-up in both powered and unpowered operations.
-
product
Transformer Testing Instrument
The Motwane Manufacturing Company
Transformers are a vital link in the electrical distribution system. Accurate and timely transformer maintenance can prevent breakdowns by detecting potential causes, and eliminating them before danger strikes. In addition, regular maintenance ensures multiple years of trouble-free operation. Motwane offers a wide range of transformer maintenance products, such as the transformer turn ratio tester, winding resistance tester, automatic oil BDV tester, and oil tan delta resistivity tester.
-
-
product
Amplifier
AC-100
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
product
Ophir Power Amplifiers
Ophir RF power amplifiers are rugged and reliable. They are available as complete rack mounted units incorporating power supply, fans and heatsinks, or as compact modules requiring a DC supply. Fans and/or heatsinks can be included if required.
-
product
High-Power Pulsed Amplifiers
High power pulsed amplifiers are capable of providing over 1KW of peak power above 10GHz. These SWaP-optimized, high-reliability products have been designed to withstand the toughest environments. For custom requirements, Mercury leverages its proven building-block design approach to rapidly deliver a solid-state power amplifier (SSPA) for your application.
-
product
T9731 High-performance Flow Test instrument with continuous measurement for EN 14683
The T9731 is specifically designed for measure the adequate air flow rate in complete adherence to the standard EN 14683 for surgical masks testing.Full scale from 10 mbar to 10,000 cc/minFlow measurement accuracy : 1% RDG + 0.1% FSFlow measurement resolution : 1 cc/minDirect pressure accuracy : 0,5% RDG + 3 DGTDirect pressure resolution : 0.001 mbar (0.1 Pa)
-
product
Solid-State High Power Amplifier 18 - 26.5 GHz
AMP4065LC-2
Exodus Advanced Communications
Designed for EMI/RFI, lab, and general communication applications. Exodus Broadband SSPA product feature GaN, GaAsFET discrete and Chip & Wire Hybrid technologies covering one octave through decades frequency ranges from Operating Frequency Range 18.0-26.5 GHz.
-
product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-02
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
product
Display Unit For The Bluetooth Connecting Instrument
MDU-100X
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Can be connected to HCL-36UX/HCL-7000X/ALCL-80X (As of Aug 2, 2022)・Data hold function available・The measured value can be displayed remotely and separately from the display of the measuring instrument・Easy to read large display
-
product
Software Encompases Instrument Control
ESCApe
ESCApeTM software encompases instrument control, data acquisition and data processing in a single, easy to use package. This is the latest generation of software for use on MS Windows operating system and replaces the long standing Vision 2 acquisition and processing software.
-
product
RF Plasma Generators & Amplifiers
100 W to 2400 W 13.56 MHz Analog/Digital, RS-232, USB interfaces Low Harmonic Distortion Automatic and Manual Gain Control High Speed Pulsing (Bursting) controls Compatible with T&C''''s Matching Networks GUI Software (complete PC control) Includes all essential RF power/communication cables and mounting brackets Air cooled (Air & Water 1200 W +) Half rack mount or stand alone versions Ideal for: Industrial, Scientific, and Medical Applications
-
product
GN Range Broadband Power Amplifiers 100 KHZ - 200 MHZ
GN Series
Class A solid stateBroadband (instantaneous single band): 100 kHz 200 MHzTypical output power : 500 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 450 W and H < -20 dBc up to 100 MHz andP1dB > 180 W and H < -20 dBc from 100 MHz to 200Air cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
