Modem Test
-
product
Conformance Test System
TS-RRM
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
product
PCI Express 5.0 Test Platform
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
product
Four Wire Modem for SEL Mirrored-Bits
MBT 9600
Application specific features set the MBT9600 Four Modem apart from the conventional high speed modems. Its compact size and ease of installation make the MBT9600 an ideal, low cost alternative to conventional audio tone teleprotection systems.The circuitry is ideally suited for use over private networks such as conventional voice channels over analog microwave.
-
product
Off-Line Base Test Platform
6TL19
The 6TL19 is a bare half-rack with castors for creating Off-Line, modular, flexible, and reliable Base test platforms. The overall rack capacity is 11U (580mm depth).
-
product
Imperial Test Executive
ITE
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
product
Wireless Transducers with GSM Modem
Wireless GSM data loggers for temperature, humidity, binary-u. counter input.
-
product
RSE Wireless EMC Spurious Emission
TS8996
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
product
IOL & Power Cycling Test Systems
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
product
Functional Test System
TS-5040
The Keysight TS-5040 Functional Test System is a cost effective, robust and reliable test system that gives you the lowest cost of ownership. In addition, the open architecture Test Exec SL gives you the flexibility to do just about anything you want.
-
product
MIMIC® Cable Modem Simulator
MIMIC Cable Modem Simulator, is the industry's first integrated simulation tool supporting DOCSIS, allows cable modem developers and cable companies to perform real world, integrated cable and internetworking device simulations. MIMIC allows suppliers of cable modems to design, develop and test their products in a virtual and scalable network environment, assuring customers that their cable modems will work properly when deployed across heterogeneous environments. Cable providers can use MIMIC to simulate the 1000s of households that use cable modems to assure the scalability of cable management software. In addition, providers can also use MIMIC for large-scale Operations Support System (OSS) testing deployments in place of large banks of cable modems, which would be cost prohibitive.
-
product
Acoustic Modem Option for Control Module
Gavia AUVs can be fitted with the Teledyne Benthos ATM-900 Acoustic Modem. The ATM-900 Series Acoustic Telemetry Modem is the most advanced, multipath and noise tolerant, modem available. They are designed to meet both the high data rate requirements of commercial users, and the higher reliability, lower data rate requirements of the military. The modems employ two modulation techniques: phase shift keying (PSK), which provides the highest bit rate, and multiple frequency shift keying (MFSK), which provides reliability in a multipath environment, or when the modems are required to operate in a low signal-to-noise (SNR) environment. The ATM-910 Series can transmit data using PSK modulation for reception by a Gavia Modem Deckbox, but receives data using MFSK modulation only. MFSK modulation is a spread spectrum modulation process that transmits multiple tones simultaneously.
-
product
MODEM SHARING DEVICES
The Modem Sharing Devices are designed to allow RS-232 DTE (terminal) devices to share Leased Line and Dial line Modems or DSU's. Data arriving at the Master Port is continually broadcast to all Subchannels. The attached terminal device that raises the RTS control signal is automatically given control of the MSD. Data rates of up to 128 Kbps are supported.
-
product
Wireless Device Functional Test Reference Solution
The Keysight S8890A Wireless Device Functional Test Reference Solution provides an automation environment which is both simple to use, yet comprehensive and powerful. Based on the Test Automation Platform www.keysight.com/find/TAP, S8890A provides optional instrument driver/plug-ins offering simplified logically grouped control steps. These steps can be sequenced, looped and swept to provide powerful individual test cases or comprehensive sequences. Each driver/plug-in is provided with extensive starter sample test cases which can be modified by Keysight or the end user the UE to be tested. Plug-in options:
-
product
SoundLink Underwater Acoustic Modems
With the innovative technologies, LinkQuest's modems have achieved significantly increased data rate (up to 38,400 baud), lower power consumption and unprecedented robustness. All of LinkQuest's modems perform at a bit error rate of less than 10 which is equivalent to the quality of wire line communication. LinkQuest's extensive line of underwater acoustic modems outperform any competing products in technical aspects for both near-vertical, horizontal and extreme horizontal underwater environments.
-
product
Application Software for Electronic Test & Instrumentation
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
Cloud Testing
Cloud is the foundation of 5G, SD-WAN, and enterprise networks. Build and maintain next-generation networks on a solid foundation.
-
product
Test Instrument
Is a programmable laser that produces picosecond pulses with pulse generator integrated. It functions as a seed pulse generator for Master Oscillator Power Amplifiers (MOPA).
-
product
Factory Testing
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Efficient factory testing is vital in order to achieve the tightest tolerances, maximum repeatability, high precisi- on and quality in the manufacturing processes, as well as long production machine lifecycles. What‘s more, it helps to reduce manufacturing costs due to minimized replacements, retesting processes, and recalibrations. Online CatalogApplication Notes
-
product
Test a Service
Enabling the automation of regression testing, verification, and validation within a functional safety environment
-
product
Compatibility Testing
Cross-Browser Testing Ensures equal user visual experience Provides identical functional behavior of applications Cross-Platform Testing Ensures flawless product processing under different OS types, versions and locales Confirms seamless application functioning
-
product
Testing and Validation
DA-Group offers accredited testing services for a wide range of electronic and mobile solutions and products. Testing and measuring are necessary during many phases of product development, manufacturing, verification and delivery. Timely and appropriate testing saves time, because this information is fed back to the development process.
-
product
Motor Test Bench For No Load Test
The testing equipment is extensively used in industries for testing of motors under no load conditions.
-
product
Functional Test
For a functional test the WEETECH test systems simulate reality and enforce switching operations that can only be tested in an embedded condition. In doing so voltages, currents, time intervals and other measurement categories are adjusted and switching sequences are processed in a way, it would happen in reality.
-
product
Connector Testing
If your product uses a connector or terminal, it can be susceptible to a unique set of failures that warrant specific connector testing conditions to determine the robustness of your design.
-
product
Test Contactor
MiCon
The MiCon™ Test Contactor is spring pin footprint compatible supporting advanced temperature requirements as well as advanced power/current requirements. The footprint compatibility allows for easy and cost-efficient conversion from spring pin setups. The fully decoupled load board side of the spring ensure no degradation of the load board pad.MiCon features a single piece design, which ensures a long lifespan, low and stable contact resistance, high current carrying capability and an extended temperature range. The MiCon allows for testing at full specification values. The extended operating range accommodates device lead trim and form variability such as device alignment accuracy and device lead coplanarity.
-
product
Functional Testing and Test Engineering
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
product
FTP Testing
TestingWhiz supports both File Transfer Protocol (FTP) and Secure Transfer Protocol (SFTP) testing. The application linked to an FTP server checks whether the data or actions performed by the user are reflected on the FTP server.
-
product
Leakage Test
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
product
Test Leads
AL-34WB
Standard Electric Works Co., Ltd
● Wire length: 1.2m approx. Silicone insulated wire (1000mm) with wire connected to straight input plugs (130mm PVC wire), and wire for clamp (100mm PVC wire). ● Outside diameter of silicone insulated wire: 5mm Outside diameter of PVC wire: 3.5mm● Input plug color: Red•Green•Black•Blue ● Current rating: 5A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V





























