-
Product
Emulate Test in simulation
STIL-VT
-
Emulate test patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test patterns. Reads the intermediate STIL format of tester patterns and creates a Verilog /VHDL simulation test bench. (A sub-set of Virtual tester solution)
-
Product
Safety Testers
-
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
Attenuator
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
-
Product
Pulsed IV-Curve Solutions
-
Pulsed IV-Curve Test and Analysis System is our new development for 2015. It is an advanced and compact pulsed IV-curve characterization system designed to simulate pulsed ESD events such as TLP, vf-TLP, HMM, HBM, EFT, and LV-Surge. It will monitor the transient voltage and current waveform during the pulse in ps or ns segment, and test the pre- and post-pulse status (leakage current, breakdown voltage, biasing current, static IV curve, etc) of the device under test (DUT), such as protection devices, semiconductors, circuit modules, touch panel sensor, etc.
-
Product
Parallel Testing of Multiple DUTs with High RF Channel Count
Test Rack UTP 7033 RF for validation
-
Our basic test rack UTP 7033 (33 rack units) is intended for equipping with various products and therefore for various application areas.The rack shown here as an example is prepared with products and measurement instruments to test automotive devices with high channel count.
-
Product
Low Voltage Burn-in and Test System
Max 450
-
For burning-in and testing DUTs such as microprocessors, DSPs and logic devices, which require low voltage. Output monitoring gives functional test results for every device during burn-in
-
Product
VPC Receiver Frame
ABex REC21-84TE-EXT
-
Robust and flexible interconnect solution for test fixtures. Designed for the use with ABex PXIe Rack 18 it provides support to equip all 21 slots with VPC interconnect modules. In addition, it offers 6 more slots on the bottom, below the ABex rack to feed through signals from external measurement devices.The interface uses the well-known Virginia Panel connectors with more than 20.000 guaranteed mating cycles. To build DUT specific test fixture, we also provide the corresponding ITA mounting frame (ITA = Interchangable Test Adapter).
-
Product
AC Ground Bond Testers
440 Series
-
The 440 Series provides advanced 4-in-1 test capability in a convenient one-box solution. This new series performs AC Hipot (448 - 500 VA), DC Hipot, Insulation Resistance and 40A AC Ground Bond tests while taking up minimal production line space. The 440 Series is simple and easy-to-use; reducing setup time and increasing production line throughput for your application. With multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Learn about our 5 Year Warranty.
-
Product
DC Power Analyzers
-
DC Power Analyzer provides unrivaled productivity gains when sourcing and measuring DC voltage and current into a DUT. The Keysight N6705C DC Power Analyzer is a highly integrated instrument that combines up to four advanced DC power supplies, DMM, oscilloscope, arbitrary waveform generator and datalogger. It provides an easy-to-use interface, with all sourcing and measuring functions available from the front panel. The N6705C makes these tasks easy:
-
Product
Modulation Distortion For E5081A Up To 44 GHz
S960707B
-
The S960707B modulation distortion software application provides nonlinear DUT behavior tests (EVM, NPR, and ACPR) under modulated stimulus conditions.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
6TL36 Plus In-line Test Handler w/Bypass
EA923
-
- Test handler 6TL36 Plus.- Dual line (bypass)- 1096 x 1875 x 1851mm [WxDxH]- Expandable to form a group with several 6TL36 modules (adapt line to production volumes).- ICT, FCT with RF, ISP or Combined test (ICT+FCT)- Servocontrolled DUT stop (stopper-less system)- Exchange time 3,2s- Max. PCB dimension 600x450mm- 19” rack space for instruments integration: 28UH- Receiver 25 slots in probe plate + 4 slots in push plate- Automatic Conveyor width adjustment- Optional Return Conveyor- High dynamics conveyors (1500 mm/s)- 90mm Top-30mm Bottom Component clearance- SMEMA and Hermes standard- CE
-
Product
High Performance PXI Functional Test System with Mac Panel Interface
TS-5400
Functional Test
The Keysight TS-5400 PXI Series Functional Test System provides automotive, aerospace and defense and industrial control manufacturers with an off-the-shelf PXI hardware and software platform with support for single or multiple DUT test. Designed for testing electronics control modules such as, power train control, complex body electronics and industrial controllers, the TS-5400 PXI Series helps manufacturers achieve higher throughput for their design validation and manufacturing functional test needs with the capacity to empower them to anticipate future functional test needs.
-
Product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
Digital I/O
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
Customized Test Fixtures
-
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
Product
Single connector for a HG cable, and two HM connectors
MVNA-8-350-2
-
The lower part of the Central Unit model MP-8-350-2 has a single connector for a HG cable, and two HM connectors (Fig. 9). Two Harmonic Mixers can work simultaneously, for instance HM2 detecting transmission through the DUT, and HM1, at port 3 of a directional coupler, detecting reflection from the DUT.
-
Product
PXIe-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
780587-15
Signal Module
PXIe, 35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXIe‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXIe‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
Product
High Voltage Optically Isolated Probes
-
High Voltage Optically Isolated Probes are designed to aid in device characterization measurements. Whether it is low or high voltage signals sitting on HV busses, high bandwidth, extreme precision, and optical isolation means floating measurements are easily made with minimal DUT loading.
-
Product
Nonlinear Component Characterization 10 MHz - 50 GHz (Export Control)
S94511B
-
The S94511B Nonlinear Component Characterization provides strong insight into the nonlinear behavior of your device under test (DUT).
-
Product
DC Automated Accelerated Reliability Test Station (AARTS)
DC-HTOL
-
The DC Automated Accelerated Reliability Test Station (AARTS) systems are designed to maximize channel density. The first systems developed by Accel-RF (ARF) were intended for RF and DC stimulus to the Device Under Test (DUT). However, there are some applications in which RF stimulus is not required.
-
Product
PXIe-4147, 4-Channel, ±8 V, 3 A Precision PXIe Source Measure Unit
786888-01
Source Measure Unit
PXIe, 4-Channel, ±8 V, 3 A Precision PXI Source Measure Unit - The PXIe-4147 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote four-wire sensing for accurate measurements. The sample rate of the PXIe-4147 can reduce measurement times, capture transient device characteristics, and help you perform current-voltage (I-V) characterization of devices-under-test (DUTs). With a high-speed sequencing engine, you can synchronize SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4147 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Low Noise Test Leads For N1413 With B2980 Series, 1.5m
N1425A
-
The N1425A is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425A is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425A enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425A to the B2985B/87B.
-
Product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
Product
MMIHF-A-DO-1, MMIHF-A-DO-1 - Shielded Tandem Test Fixture
100229
-
MMIHF-A-DO-1 - shielded tandem test fixture with single mechanics for high frequency and radio applications. Protection of the environment from the DUT or shielding of interferences on the test. With our high-frequency fixture you can test sensitive and transmitting assemblies - even those with a combination of transmitter and receiver - in detail without risking consequences for your production.
-
Product
Signal Analyzer
-
bsw TestSystems & Consulting AG
The simplest way to measure the phase noise is to compare the Device-Under-Test (DUT) to the source of a spectrum analyzer. With the SA set at the same frequency as the OUT, you see the sum of the SA's and DUT's sideband-power spectrum on the SA display. It is a simple and straight forward method well suited for free running VCO's where the SA is easily an order better.You can improve on this method by establishing a Phase Lock (PLL) between the DUT and the Local Oscillator and create a zero-IF or base-band spectrum analyzer system.
-
Product
DC Power Module, 35V, 1.5A, 50W
N6734B
Power Module
The Keysight N6734B is a 52.5 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Bit Error Rate Tester
100G NRZ BERT
-
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
-
Product
Power/Voltage Rail Probe. 4 GHz Bandwidth, 1.2x Attenuation, +/-30V Offset, +/-800mV
RP4030
-
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
Product
Sound Harmonics and Current Analyzer
H74050100
Audio Analyzer
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
