-
Product
ADC DAC Module
ZET 220
-
ZET 220 ADC DAC module with 24-digit ADC converters is used for high-precision signals measurements in wide dynamic range. The signals to be measured are received from primary transducers – for instance, from sensors with 4-20 mA current output.
-
Product
PXI-4461, 204.8 kS/s, 2-Input/2-Output PXI Sound and Vibration Module
779687-01
Analog Input Module
204.8 kS/s, 2-Input/2-Output PXI Sound and Vibration Module—The PXI‑4461 is designed for sound and vibration applications. It provides two-channel dynamic signal generation and two-channel acquisition, and you can use one of six gain settings to configure your input range. The PXI‑4461 also includes software-configurable AC/DC coupling and IEPE conditioning. The PXI‑4461 includes the hardware and software needed to make precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications include audio test; automotive noise, vibration, and harshness (NVH); and machine condition monitoring.
-
Product
LED Power Driver ATS
8491
-
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
Product
Power System Analyzer
931A
-
Model 931A, with state-of-the-art PowerDSA™ Digital Signal Analysis, make more measurements, more accurately, and at a lower price than ever before. Basic accuracy of 0.05 % of reading and 0.05 ° phase, harmonic analysis, and full three-phase capability are standard. Model 931A also incorporate full two way serial communication for use in power quality trend monitoring. The model expands usability by including transducer calibration and timer features.
-
Product
Neodymium Low Frequency Transducers
-
High energy neodymium magnetic designs, complex cooling systems and new technologies for high-power handling, minimal distortion and low weight.
-
Product
TMR Current Sensors
-
MultiDimension Technology Co.,Ltd.
An open-close current transducer, high sensitivity and signal-to-noise ratio TMR chips are used in the design, which based on Tunneling magneto resistance effect. The transducer has a built-in temperature compensation and nonlinear compensation circuit, which can accurately measure DC, AC and pulse current. The transducer has many benefits ,such as high precision, wide bandwidth, low power consumption, excellent isolation performance and so on. Besides, the design of open-close structure makes it easier to install and unload.
-
Product
Pressure Sensor Kit for Changing Ranges
DP15TL
-
The wide range of diaphragms furnished eliminates expensive stocking of several transducers and offers the versatility of the differential type bi-directional transducer at a very low cost. The broad line pressure capability of this unit makes it useful in almost every laboratory application from flow to level measurement, vacuum to 3000 PSIG. The high output, when used with a carrier system such as the Model CD15 Sine Wave Carrier Demodulator or the CD12 Transducer Indicator, provides resolution equal to many secondary standard units.
-
Product
Transducer Simulator
Model 7V
-
Impedance: 350 ohms nominal. Output Ranges:Fixed rotary switch: 0 to 3 mv/v in 6 steps of .5 mv/v .
-
Product
Calibration Kits
-
Atec’s Portable Calibration Kit, PN AHT63506-1, is used to calibrate instrumentation and transducers in engine test cells, as required per T.O. 33K6-4-3416-1 or Atec Technical Manuals.
-
Product
3 Phase Voltage Transducer
-
Converts a three phase, 600 VAC, 50/60 Hz power system to three proportional 0 to 5 volt DC outputs.
-
Product
Pressure Transducers
-
Procter & Chester Measurements Ltd
A transducer is a generic name that is a device which is usually electronic that coverts a physical attribute to a measurement signal.
-
Product
Advanced Ultrasonic Thickness Gage
-
The 45MG is an advanced ultrasonic thickness gage packed with standard measurement features and software options. This unique instrument is compatible with the complete range of Olympus dual element and single element thickness gage transducers.
-
Product
Flexible Current Sensor Probe
CTA
-
The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.
-
Product
Magnetic Field Transducer With Integrated 1-Axis (By) Hall Probe
I1A
-
The I1A Magnetic Field Transducer with Integrated 1-axis (By) Hall Probe is designed to measure magnetic fields perpendicular to the probe plane with exceptional accuracy and precision. This transducer is renowned for its low noise and minimal offset fluctuations, ensuring reliable measurements in various applications. The small form factor of the integrated Hall element, measuring just 22 μm x 22 μm, yields remarkable spatial resolution, making it ideal for tasks such as magnetic field mapping and characterization of permanent magnets. Coupled with its integrated temperature sensor, this device allows for effective temperature compensation, greatly enhancing measurement consistency.The I1A transducer excels in different magnetic flux density ranges, including ±0.1T, ±0.2T, ±1T, and ±5T, which can accommodate a variety of applications from laboratory research to on-line quality control in production environments. With an output voltage that is high-level differential and proportional to the measured transverse magnetic flux density, it ensures accurate data transfer. The built-in modules for conditioning signals include features for amplification, non-linearity correction, and sensitivity adjustments that compensate for temperature variations, further enhancing its performance in real-world applications.
-
Product
Bridge Amplifier
90376
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
-
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
-
Product
Hydrophones
-
Operating principle of the hydrophones by ZETLAB Company is based on the piezo-electrical effect, which allows to use them as linear and reversible hydroacoustic transducers. The hydrophones by ZETLAB Company meet the requirements of sound environment non-distortion, wide frequency range, and non-directedness.
-
Product
NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
785044-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
-
Product
UPG-07 Ultrasonic Precision Thickness Gages - Color
UPG-07
-
100K thickness datalogger with export to Excel 8 0z. Operates on 2 AA batteries Measures all engineering material Store and Recall setup for use with multiple materials All software options are field-upgradeable Vibrate and color change on alarm Illuminate the keypad on alarm condition Inform the operator when to replace the transducer Simple user-interface
-
Product
Load Cells
-
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Process Voltage & Current Data Loggers
-
Monitor and log virtually any process voltage or current output from your transducers.
-
Product
Button Load Cell
3000 Series
-
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
Product
Level & Pressure Transmitters
-
This series of low-pressure transducers is specifically designed for demanding industrial applications where the primary criteria are reliability and economy. These units provide repeatable, precision measurements under the most hostile condition.
-
Product
Linear Variable Differential Transformers (LVDTs)
-
Whilst there are several ways to measure displacement, the Linear Variable Differential Transformer (LVDT) remains a popular transducer in most industrial applications. LVDTs initially were used as a means of taking dimensional readings in laboratories. They gained popularity in a wide variety of industrial monitoring and control applications, and whilst an LVDT is used to measure displacement the technology can be employed within other transducer types.
-
Product
Run Down Adapters
-
Testing power torque tools is essential for product quality and regulatory compliance. A run down adapter is designed is to simulate the fastening process of a screw. Mountz run down adapters improve testing repeatability by adjusting for the impact force and irregular peaks of power tools. Mounted in-line between the tool's driver and transducer, a run down adapter provides consistent and reliable torque readings.
-
Product
Signal Conditioners & Measuring Transducers
-
Signal conditioners and measuring transducers ensure interference-free signal transmission in measurement and control technology. From highly compact 6 mm signal conditioners and measuring transducers through signal conditioners with functional safety to signal isolators for intrinsically safe circuits in the Ex area: our signal conditioners and measuring transducers ensure interference-free signal transmission in MCR technology.
-
Product
Industrial Current Sensors
RCT
-
Power Electronic Measurments Ltd
The RCT range of AC current transducers are designed for permanent or semi-permanent installation and are available with industry standard outputs.
-
Product
High Accuracy AC Reference Source
515
-
Clarke-Hess Communications Research
The Model 515 High Accuracy AC Reference Generator fills a need for a relatively low cost and practical solution for supplying a reference excitation to typical LVDT and Synchro/Resolver transducers. The Model 515 has built-in load sensing which, in effect, yields "zero" output impedance and virtually eliminates the effects of fluctuating output loads. With up to 15 VA of output into loads with as much as 80 of phase shift, the Model 515 is ideally suited to driving inductive loads.
