VMEbus
VERSAmodule Eurocard bus
-
Product
64 bit, 66 MHz Metering PMC to PMC Extender
8100
-
The metering PMC to PMC extender is a comprehensive development tool for use with PMC cards on a VMEbus, Compact PCI, or other carrier card.
-
Product
16-Channel VME RTD/Resistance Input Module
V410
-
The V410 is a 6U VME module that provides sixteen independent analog inputs that may be used to read RTDs, thermistors, and other similar resistive sensors. It can also read cryogenic diodes. Users may set input range and adjust other settings at VMEbus speed, and depending on the range selected the microprocessor will do the necessary calculations and output voltage, resistance, or temperature. Temperature conversion is available for 100Ω and 1000Ω, series 385 and 392, platinum RTDs.
-
Product
Digital Output Board
VME-2533
Digital Output Board
VME-2533 32-bit Differential Digital Output Board. VMEbus specification compatible double height form factor.
-
Product
PMC/XMC Expansion Card
EXP238
-
The EXP238 is a 6U VMEbus form factor expansion card offering three XMC/PMC expansion sites. When ordered as an option for the XVB603 VMEbus single board computer, the 3-slot solution greatly expands system flexibility.
-
Product
Interface
RQVME2-1553
Interface
The RQVME2-1553 provides new levels of performance and flexibility for MIL-STD-1553A and B Notice II on the VMEbus. Available in commercial, industrial and conductively cooled versions with one, two or four dual-redundant channels, the RQVME2-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
Stepper Motor Controller for VMEbus
VME321
-
The VME321 Intelligent Stepper Motor Controller with Amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.This VMEbus board has a 6U form and is also available as 3U VMEbus board.
-
Product
XMCspan XMC Expansion Board
XMCspan
-
The XMCspan allows users to customize and expand I/O options when coupled with VMEbus SBCs, adding up to 4 XMC or PMC slots.
-
Product
Digital Output
VME-2170A
Digital Output Board
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
Product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
-
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
Product
Expansion Card
PMC238
-
The PMC238 is a 6U form factor card that expands a single PMC site on a VMEbus processor board to two PMC sites and one PCMCIA/CardBus socket or to three PMC sites. Compatible with many VMEbus single board computers, it provides an extension of PCI and PCMCIA capacity within the VMEbus form factor. The PMC238 has the option for the PCMCIA/CardBus cards to be mounted outside the chassis using an 18-inch cable.
-
Product
4/8 Channel 10 bit 2/1 GS/s Digitizer
V1751
-
The V1751 comes in a VME form factor with 4/8 input channels (4 channels in case of DES mode*). The communication to and from the board is provided through the VMEBus and Optical Link interfaces.
-
Product
Powered VME Crates
-
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSAbus electrical specifications (1979) with the Eurocard format resulting in the VMEbus Revision A - 1981 specification. The VMEbus specification has since then been refined through revisons B (1982), C, C.1, IEC 821 & IEC297 and IEEE 1014-1987.
-
Product
Dual Channel Digital Receiver
MS 1740
-
Dual Channel Digital Receiver is a complete high−frequency dual−channel A/D converter capable of sampling rates up to 210 MHz. It accepts two front panel analog inputs and delivers digital output samples over four FPDP (Front Panel Data Port) connectors utilizing FPDP standards. The Dual Channel Digital Receiver features two 12−bit Analog Devices AD9430 A/D Converters, and two user−configurable Xilinx® Virtex−IV Series FPGAs. It also features a VME A64/D64 slave interface for setting up operating modes and selectable A/D range, and optionally provides 32−bit access from the VMEbus to the FPGAs. It is an ideal system as a high−speed data acquisition front end for real time recording and digital signal processing systems.
-
Product
VMEbus board
IIB-429--VME-4C
-
The IIB-429-VME-4C provides 16 ARINC-429 compatible channels (8 receive and 8 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-VME-4C is built upon a flexible platform, user function can be implemented almost without restriction, making this product flexible and user-friendly. This VMEbus board has a 6U form factor. This VME unit is also available in a 3U form factor, as IIB-429-VME.
-
Product
VME Form Factor Extender, 6U, 180mm
111FFE6018-012X
-
The VME form factor extender 6U 180 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
VME Form Factor Extender, 6U, 120mm
111FFE6012-012X
-
The VME form factor extender 6U 120 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
