Test Harness
See Also: Harness Test, Harness, Harness Testers
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
product
Cable Harness Test System
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20,000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
-
product
Communication Protocol Test Harness
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
product
Wire Harness/Automotive Probes
As a market leader, Feinmetall offers the largest product portfolio of application-specific contact probes and accessories for test module construction and wire harness testing. With innovative and economical solutions, we meet customer requirements and set trends in wire harness and automotive testing technology.
-
product
High Voltage Insulation Tester Module
DP-cPCI-5586
DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.
-
product
ATE & Test Systems
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
product
SilverCreek SNMP Tests
Set up in less than five minutes - Windows or LinuxCustomize tests via Wizards, Script Generators, and moreAutomate operation with unambiguous test resultsIntegrate with other test harnesses and test toolsIncludes conformance, compliance, vulnerability, robustness, stress, and performance testingInvestigate failures and quickly resolve them with powerful diagnostic and analysis tools
-
product
Test Management Software
Easy to use to minimal training. Our Test Management Software is powerful enough to accommodate all of your electrical and function testing requirements, whether testing a cable harness or fully equipped vehicle or aircraft.
-
product
Custom Wiring Harnesses and Cables
From flight critical aerospace wiring harnesses to discrete wire assemblies, WinSoft can meet your toughest requirements. Each of our finished cable assemblies and wire harnesses is built to the customer exact specifications and is 100% quality tested. Cable and harness assemblies are certified to meet all customer requirements and applicable industry standards while manufactured to strict ISO processes and procedures.
-
product
Cable Tester
FST-500 High Voltage Cable Tester is a modular and customizable cable tester that can be easily adapted to various cable test or cable harness test applications. The electronics is based on Finero’s rugged industrial grade FST range of standard test equipment. All set and measured values are shown on alphanumeric display, additionally there is an analog panel meter for output voltage. Other cable paramerter like L, C and R can also be tested by using optional test and measurement equipment. The tester can be ordered with a build in PC and it can be used in conjunction with Finero’s Quality Control software.
-
product
Ada Embedded Software Test Solution
VectorCAST/Ada
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing Ada software components necessary for validating safety- and mission-critical embedded systems. VectorCAST/Ada parses your source code and invokes code generators to automatically create the test code (stubs and drivers) required to construct a complete, executable test harness.
-
product
Threaded Probes Designed for Connector and Harness Test
Equip-Test Threaded Probes Designed for Connector and Harness Test
-
product
PC Controlled Low Voltage Testers
PC Based Testers Low Voltage Introduction. The PC based analyzers provide high-speed testing for wire harnesses, backplanes, and printed-circuit boards.
-
product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
product
Handheld Wiring Analyzer
HT-128
Simplify your wire harness testing. The DIT-MCO HT-128 provides a superior solution for point-to-point continuity analysis. These lightweight, handheld units can serve your diagnostic needs from product development and benchtop testing through field support and maintenance.
-
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
product
Breakout Tools
Quickly test and troubleshoot harnesses, engine control modules or sensors by connecting a Breakout Box onto your system.
-
product
PCB Test Fixtures
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
product
Interior Wiring Testing
With automotive interior designs becoming more luxurious, cabin space features such as ambient lighting and seat / steering wheel controls have increased the demand for interior wiring testing. Jackmark Engineering has years of experience supplying test equipment for instrument panel manufacturers and have increased their portfolio to include all aspects of interior wire harness testing.
-
product
Modular Test System
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
product
Imperial Test Executive
ITE
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
product
Semiconductors Testing
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
product
Test Workflow Standard
Test Workflow equips engineers with application-specific tools so that they can choose the right one for the job—from graphical programing environments to no-code and interactive software applications. Engineers can use Test Workflow software to perform quick ad-hoc tests, build an automated test system, automate data analysis and reporting, develop test sequences, and more.
-
product
Cable Free ATE
CABLEFREEATE
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
-
product
Wafer-Level Parametric Test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
product
Automatic Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
product
Scienlab Battery Test System – Module Level
SL1001A Series
The SL1001A and SL1006A Battery Test Systems – Module Level Series help you emulate sink and source for battery modules for automotive and industrial applications.
-
product
Fast and Flexible WLAN Measurements up to 802.11ax
WLAN Test Toolkit
The WLAN Test Toolkit gives you direct and fine control over the generation and analysis of IEEE 802.11a/b/g/n/ac and ax signals, as well as 802.11j/p/ah/af waveforms, with industry-leading speed and accuracy. It empowers you to characterize, validate, and test a variety of WLAN connectivity products, such as RF front end components, wireless modules, and user devices.The toolkit includes extensive support for the latest features of the 802.11ax standard, including extended single-user packets, multiuser OFDMA, and multiuser multiple input, multiple output (MIMO) functionality with per-user configuration and measurement results. The WLAN Test Toolkit helps you solve demanding new access point test cases by generating signals that simulate multiuser environments, including per-user impairments. You can also use the new software to generate trigger frames to test the real-time response of client devices and make power precorrection and relative center frequency measurements.
