Signaling Testers
-
product
RF PHY Tester
TLF3000
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
product
Signal Generator
8006
Normal switching mode, SSB phase noise will be degraded in the fast mode. 5 digit BCD, 1 latch control line, 25 pin female, D type connector
-
product
100MHz DDS Signal Generator
408A
The 408A generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The 408A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution.The Frequency is accurate to 1ppm when using the on board TCXO timebase or it can be factory configured to use an external frequency input as the timebase. A Line Voltage AC Adapter and a CD containing SOF8 windows softwareare included. A DDS8m is used inside the 408A.
-
product
PWM TO VOLTAGE SIGNAL CONVERTER
RCPWM2V
The RCPWM2V is a device that converts a standard hobby RC signal (1-2ms pulse) into a proportional analog voltage (0-5V). In many electronics applications the main processor is constantly busy and does not have the ability to address the time-sensitive PWM signal from an RC receiver immediately. This results in signal distortion or a sluggish response due to the extra filtering required. The RCPWM2V provides a simple solution by converting the signal into an analog signal. The main processor can then read the signal whenever it has time.
-
-
product
Safety Tester
Safety analyzer is mainly used to provide the test solution for electric car, grid, photovoltaic, electrical appliances, information equipment, medical equipment industry as well as innovative solutions for the various electrical measurement.
-
product
Electric Safety Tester
PV-215
The multifunction device PV-215 allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
product
WAN Tester III
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
product
PXI-5670, 2.7 GHz RF Vector Signal Generators
PXI-5670 / 778768-03
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
product
3-28V Cordless Circuit Tester
1948
Peaceful Thriving Enterprise Co Ltd
With CE & UKCA Approvals. Detect voltage from 3V to 28V. No ground wire or clip required. Replaceable long-life alkaline batteries included.(Power supply: SUM5 1.5V X 2 pc). Safe with ECMs, sensors, transducers and air bags.
-
product
Weld Testers
The Weld Tester is our most versatile electrochemical monitoring instrument. Housed in a substantial metal case with brushed anodised aluminium front panel and green military specification connectors this equipment looks functional and professional. The top row of connectors are exactly the same as provided on a Gill 12 whilst the bottom row are for the additional weld segments. Using the same Potentiostat, Galvanostat, Zero Resistance Ammeter with integrated Frequency Response Analyser and Sweep Generator as a Gill 12 allows all the tests supplied with the Gill 12 to be supplied with the Weld Tester.
-
product
Electrical Testers
Digital voltage and continuity tester with LCD screenAC and DC voltage testing (7 thresholds) with automatic AC or DC detection, audible continuity and single-pole phase test.
-
product
Hipot Tester
HAL
The HAL Series combines over 50 years of expertise in ensuring the electrical safety of manufactured electrical products.
-
product
LED Driver Online Tester
LEDLS-60/LEDLS-12
• The tester includes A Group Measuring Module and B Group Measuring Module. The A Group measuring module can test 6pcs LED Driver AC Parameters. The B Group measuring module can test 6pcs LED Driver AC, DC and AC/DC Parameters. • There are 12 windows to display the input and output parameters, it is good for comparing and analyses. • Quick test for all of the parameters in 0.1 seconds. • It can set up the testing parameters PASS/FAIL range, it will have Noise/Light warning if it is Fail. We also supply handle port (Extra cost) • Software communicate with PC (Extra cost)
-
product
PAT TESTER
Precision Mastech Enterprises Co.
The Safety Pat Plus is a handheld battery powered unit suitable for carrying out electrical safety tests.Stores 300 test results and can be battery & mains powered. The instrument is capable of testing surge protected equipment & can test 110V, 230V appliances. It will return true leakage results at both 110V and 230V
-
product
Installation Safety Testers
VDE 0100
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
product
Signal Injectors
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
product
Friction and Wear Tester
EFM-III Series
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
product
Signal Conditioners
Frequency to Voltage
Encore Electronics offers a complete line of frequency to voltage converters ranging from the economically priced and compact DIN rail mounted Model FL228 to the rack mounted Model 225. For applications requiring performance between these two models, we now offer our FL236 DIN-rail packaged Digital Frequency/Voltage converter, featuring fast response time, low power and compact footprint.
-
product
Battery Load Tester
MD4260
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
product
IK Level Tester
IK07-10
IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
-
product
NFPA 701-2 Flammability Tester
TF321
TESTEX Testing Equipment Systems Ltd.
NFPA 701-2 Flammability Tester, to determine the ignition resistance properties of draperies and other hanging fabrics according to test method NFPA 701#2, and it is suitable for single-layer or multi-layer fabrics, fabrics with density larger than 700g/m2 (21oz/yd2), and fabrics coating with polyethylene, etc.
-
-
-
product
Precise Ball-fall Tester
King Design Industrial Co., Ltd.
Auto-lift device; accuracy is to 1mm. Precise-casting formed; won’t influence floor structure. Good test-repeatability; easy to operate. Can measure the hit time & maximum shock force. Conform to CNS & JIS specifications. Can output report, save file and make record. Can extend the optingal functions and measure joule. Anvil seat size can be changed to any size. Chinese measuring interface; easy to comprehend and operate. Timely observe the energy and shock force. Pull-down window; fast in setting.
-
product
Battery Tester
G5.BT
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
product
Analogue ELCB Tester
810 EL
Standard Electric Works Co., Ltd
● Wiring check.● Can be used on 2 wires L-E (ELCB/RCCB/GFCI tester).● Can be used on 3 wires L-E-N (with wiring check).● Sense automatically 50 or 60 Hz.● No battery required.● Simple operation.● Current injected in phase with the voltage.● Fused.● Wide operating voltage (195Vac to 265Vac).● Other voltage optional (110V).● Robust.
-
product
Digital Earth Resistance Tester
MODEL - KM 2030
Kusam Electrical Industries Limited
Display : 3½ Digit LCD display. Ground resistance measurements from 0 ~ 01Ω to 2000Ω with 0.01Ω resolution. Earth Resistance : 20Ω / 200Ω / 2000Ω. Accuracy : 20Ω : ± (2% + 0.1Ω); 200Ω / 2000Ω : ± (2% + 3). Earth Voltage : 0 ~ 30V. Accuracy : ± (3% + 5). Resolution : 0.01Ω. Working LED Indicator. Data Hold Function.
-
product
Non-Contact Voltage Tester
NCVT-3
Provides non-contact detection of AC voltage.Detects 12 – 1000V AC with simultaneous visual and audible voltage indicators.Bright flashlight illuminates work area and may be used independent of voltage detection function.Visual LED bar graph indicates the presence of voltage – the higher the voltage sensed, or the closer to the voltage source, the more LEDs light up.Bar graph visual voltage indicator utilizes up to five vibrant LEDs for easy interpretation/viewing.Audible voltage indicator beeps at a greater frequency the higher the voltage that is sensed, or the closer to the voltage source.“Auto Power-Off” conserves and extends battery life.Screw-thread battery cap with O-ring ensures protection against dust and water ingress.Lightweight, compact tool with pocket clip provides convenient storage and quick access.IP67: Dustproof and waterproof.6.6 feet / 2 meter drop protection.CAT IV safety rating for 1000V.Conforms to CE requirements.
-
product
SMD LED Aging Tester
Shenzhen Chuangxin Instruments Co., Ltd.
LED life tester with 150 independent constant current to aging-life and color comparisons of 50pcs 5050 SMD LED and 100pcs 3528 SMD LED.
