Synchro / Resolver Simulators
See Also: Synchro/Resolvers
-
product
Resistor Simulation Card
SET-1210
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
product
ARINC825 (CAN Bus) Test & Simulation Module for CPCI With 2 Or 4 CAN Bus Nodes
ACC825-3U-x
ARINC825 (CAN bus) Test & Simulation module for CPCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACC825-3U-x CPCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
PXI RTD Simulator Module 12 Channel PT100
40-262-201
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the design principles of our 40-260 PXI Precision Resistor, this RTD simulator module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels.
-
product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Virtual Platform Simulation Acceleration
QuantumLeap
QuantumLeap is a parallel simulation performance accelerator that leverages a new synchronization algorithm to provide the fastest virtual platform software execution speed available. The execution performance of this new technology has been measured on average at 15 times faster than the nearest commercial solution using standard benchmarks.
-
product
BRI and PRI Simulator
emutel Ultra
emutel Ultra is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Ultra can emulate different country specific networks by adding network personality cards & networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Ultra.
-
product
Dual API and Synchro Transmitter Panel
TA-1001
This is our Dual API and Dual Synchro transmitter panel that is ideal for testing any HSI or ADI in your shop. Industry standard precision 18:1 drives are provided to deliver the accuracy required by many OEM companies when testing and aligning their instruments. Click on picture for larger view.
-
product
Synchro to DC Sine / Cosine Converters
SD
Computer Conversions Corporation
This unique series of Synchro to DC Converters makes use of advanced digital circuitry techniques to accomplish high speed conversion with extreme accuracy. Transformer isolation as well as balanced line-to-line input impedance is provided for superior and trouble-free system performance, regardless of the input synchro used.
-
product
Basic Rate ISDN and IDSL Network Simulator
Emutel Solo
Emutel Solo is a small, portable lightweight battery powered basic rate ISDN and IDSL network simulator. With 2 software switchable S/U interfaces and the choice of either Euro-ISDN, North American or NTT support. Emutel Solo allows you to test and demonstrate all types of BRI equipment on one compact unit. Providing all the standard features but also many others that its compeditors don't include.
-
product
Resistance Temperature Detectors (RTD) Simulators
Simulation of resistance based temperature sensors such as positive or negative temperature coefficient thermistors. Resistance Temperature Detectors (RTDs) can be wire-wound or thin film. Our RTD simulator modules provide a cost-effective method of simulating both PT100 and PT1000 RTD sensor types that require fine setting resolution.
-
product
Four Quadrant Power Amplifier For Simulation Applicaton
PAV30000
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
product
2 PRI + 8 Port FXS PSTN Simulator Adv
CH-8FXS-MOD-2PRI-A
One of the most feature rich PSTN simulator on the market. Unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
product
Resolver to Digital and Digital to Resolver Converter
DP-VME-5031
DP-VME-5031 is a Resolver to Digital and Digital to Resolver Converter module. This module has four resolver to digital converters as measurement channels and six digital to resolver converters as stimulus channels.
-
product
Telemetry Simulators & Test Transmitters
Command Data Telemetry Simulators offer a dynamic way to create or change a PCM data stream on a word by word basis on the fly. This PCM data stream can be used to modulate an FM or SOQPSK RF output at S-Band or L-Band. In addition to simulating a new telemetry stream, the telemetry simulators can play back and loop an archived data file (which can also be changed on the fly) or create pseudo-random patterns.
-
product
Graphical Debugging for Verilog, VHDL, and C++ Simulators
BugHunter Pro
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.
-
product
PCI Strain Gauge Simulator Card, 4-Channel, 350 Ohm
50-265-014
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
UV Solar Simulators
UV Solar Simulators - please contact the company directly for more information.
-
product
Au Truck / Bus Fleet Management System (FMS) Simulators
The Au Truck / Bus Fleet Management System (FMS) simulator can generate Controller Area Network (CAN) signal per Truck FMS Standard (Vers. 02.00) and Bus FMS Standard (Vers. 00.02). Au FMS simulators are designed very easy to use. All editions can run independently (without personal computer). Au FMS Simulators are widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration, to product development and product validation.
-
product
Modbus Simulator & Tester
Modbus Poll
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
product
Non-Hydraulic Steering Module Test Simulator
SMTS
The Steering Module Test Simulator (SMTS) from MB Dynamics is a non-hydraulic turnkey lab test system, offering accurate, reliable and repeatable in-laboratory simulations of driver, road & vehicle inputs acting on a steering system, and their associated effects on steering system performance and annoying noises. Supports troubleshooting, identification, diagnosis, and resolution of root causes of unwanted noise and other performance issues common to EPS, EPHS, EPAS, MDPS, and HPS steering systems.
-
product
Multi-Protocol Test & Simulation Adapter for USB or Ethernet
EXC-UNET2/xx
The EXC-UNET2/xx is a multi-protocol test and simulation adapter for USB or Ethernet equipped computers. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of a number of communications protocols, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
LXI Simulation Tool
60-901-001
This tool will simulate all of our PXI & LXI switching products and most of our PXI simulation products allowing for code development independent from your application hardware
-
product
Basic Rate and Primary Rate Simulator
emutel Pro
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
product
Windows Server Simulation Software For BACnet Systems
BACSim
BACsim is the industry's first easy-to-use BACnet device simulator for Windows. BACsim runs under Windows 7/8/10 and Server 2012, and provides a robust set of basic simulator features tailored to the needs of BACnet designers and testers.
-
product
Altitude Simulation Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Altitude Simulation Test Chamber
-
product
PCI Express Mini Card For MIL-STD-1553 Test And Simulation
AME1553-1
MIL-STD-1553 Test and Simulation PCI Express Mini Card with 1 Dual Redundant channel plus 2 discrete Input, 2 discrete Output channels.
-
product
GNSS Simulator
NCS NOVA
The NCS NOVA is IFEN´s newest RF signal generator technology based on a modular and highly flexible Software Defined Radio (SDR) platform. This flexibility makes the NCS NOVA the ideal choice for a wide range of test applications.The NCS NOVA`s full upgradeability makes it a future-proof investment for the upcoming multi-frequency era in commercial and professional applications. It is far more than just a GPS/GNSS Simulator!
-
product
2 Port BRI-S/T-U ISDN Simulator
BRI-2UST
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
